UC Living Rosmore Slide Control Operating and maintenance manual

Rosmore Slide Control
INCLUDES USER, INSTALLATION & MAINTENANCE
INSTRUCTIONS
Please read these instructions carefully before you start using the
appliance
Keep this booklet handy for future reference
This appliance is
for use in GREAT BRITAIN or IRELAND only

LT ())
UC Living Rosmore SLIDE CONTROL Instructions
CONTENTS
PAGE
User Instructions 3
SECTION ONE Introduction 3
Consumer Protection 3
Health and Safety 3
Introduction 3
SECTION TWO Operation 4
SECTION THREE Fuel Bed Cleaning and Layout 5
Coal Layout 5
Pebble Layout 7
SECTION FOUR Important information 10
INSTALLATION INSTRUCTIONS 11
SECTION FIVE Specification 11
SECTION SIX Regulations and Warnings 11
SECTION SEVEN Siting the Appliance 12
Class One 12
Class Two Fabricated Metal 13
SECTION EIGHT Fireplace Requirements 13
Clearance to Shelf 13
Clearance to Side of Fire 14
Ventilation 14
SECTION NINE To Install the Appliance 14
Examine Flue /Chimney 14
Connecting to the Gas Supply 14
Preparing the Appliance for Gas Connection 15
Gas Connection from the Front 16
Fixing Fire into Opening 16
Optional Cable Fixing System 16
Checking Gas Soundness 17
Connecting Control Lever 17
Checking Operation of Fire 18
Checking Product Clearance 18
Completion of Installation 18
Advise Customer That 18
MAINTENANCE INSTRUCTIONS 19
SECTION TEN Maintenance 19
General 19
Fuel Bed Cleaning 19
Pilot Linting 19
Replacement of Gas Control 19
Replacement of Burner and or Silencer 20
Replacement of Injector 20
Replacement of Pilot Assembly 20

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION ONE Introduction
Consumer Protection Information
As manufacturers and suppliers of heating products, we take every care, as far as is reasonably
practicable, that these products are so designed and constructed as to meet the general safety
requirement when properly used and installed. To this end, our products are thoroughly tested
and examined before despatch.
IMPORTANT NOTICE: Any alteration that is not approved by the appliance manufacturer could
invalidate the approval of the appliance, operation of the warranty and could affect your
statutory rights.
Health and Safety Notice
Important
This appliance could contain some of the materials, indicated below, that could be interpreted
as being injurious to health and safety. It is the users / installers responsibility to ensure that the
necessary personal protective clothing is worn when handling these materials, see below for
information.
Artificial Fuels, Mineral Wool, Insulation Material, Refractory/Ceramic Fibres, Glass Yarn -
may be harmful if inhaled, may be irritating to skin, eyes, nose and throat.
When handling avoid inhaling and contact with skin or eyes. Use disposable gloves,
facemasks and eye protection. After handling wash hands and other exposed parts. If a vacuum
is used for cleaning the fuel bed or cleaning after servicing / installation it is recommended that
it be of the type fitted with a HEPA filter.
Disposal of refractory/ceramic materials. To keep dust to a minimum these materials should
be securely wrapped in polythene and be clearly labelled ‘RCF waste’. These materials are not
classified as ‘hazardous waste and should be disposed of at a site licensed for the disposal of
industrial waste.
INTRODUCTION
The UC Living Rosmore SLIDE CONTROL is a decorative fuel effect appliance with a radiant
heat conserver box for improved efficiency.
The UC Living Rosmore SLIDE CONTROL is designed and tested to the requirements of EN
509
The UC Living Rosmore SLIDE CONTROL should be installed and serviced by a competent
person i.e. Gas Safe registered, in accordance with the current Gas Safety (Installation and
Use) Regulations 1998 (as amended).
The chimney or flue (unless new) must be swept before installation if it has been used for solid
fuel or oil.
The UC Living Rosmore SLIDE CONTROL is available in two versions Natural Gas or LPG
(Propane Gas Only). The markings (G20 for natural gas or G31 for propane) on the packaging
and the data badge specify the gas for which the appliance has been factory set. Note: These
appliances should only be used on the appropriate gas specified. They are not suitable
for conversion from one gas to the other.

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION ONE Introduction Continued
The UC Living Rosmore SLIDE CONTROL incorporates a single gas control, which selects
ignition pilot, and main burner low and high settings.
The UC Living Rosmore SLIDE CONTROL incorporates a safety device in the form of an
Oxygen Depletion System, which constantly monitors the oxygen in the room and will cause the
fire to switch off if the oxygen level reduces, for instance due to insufficient ventilation or a
blocked flue.
If this repeatedly occurs do not attempt to relight the appliance until a qualified engineer has
checked it, the problem may not be due to lack of air or a defective flue.
Warning:-This appliance has a naked flame, has with all such fires it is essential that a
fireguard should be used for the protection of children, the elderly and infirm. Fireguards should
conform to BS 6539 (1984) (Fireguards for use with solid fuel appliances).
During the normal operation of the fire some black staining may appear on some parts of the
fuel bed. This is quite normal and adds to the appearance of the appliance. However, if
excessive black staining does occur it may be due to the fuel bed being incorrectly laid. This
should be checked prior to contacting a service engineer.
SECTION TWO Operation
The full lighting procedure is as follows: -
a. Push slide control lever down, as far as possible a clicking noise will be heard and the
pilot will light, HOLD DOWN FIRMLY FOR ABOUT 20 SECONDS.
b. Pull lever up and the pilot light should remain alight and the main burner should light on
its low setting.
c. Should the pilot fail to light, pull the lever fully up to turn off the appliance, wait 3 minutes
and repeat the procedure (a &b). If the pilot does not light and no clicking noise is heard
replace the battery and try again.
d. After lighting the pilot flame and the main burner on its low setting the control lever may
be lifted until slight resistance is felt, this will put the burner on its high setting.
e. To completely extinguish the fire, pull the lever up past the resistance to its fullest extent.
f. The fire may be operated on either its low or high setting.
g. It is recommended that the appliance is operated on its high setting for a short period
before adjusting to the low setting.
h. If the ignition does not operate fit a new 9V battery (PP3/MN1602) to the ignition unit,
located behind the fret adjacent to the gas inlet pipe, and repeat ignition procedure prior
to reporting a fault.
Note: -If the ignition fails the pilot can be lit with a taper or a match held at the pilot head.

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION THREE Fuel Bed Cleaning and Layout
Important: - Refer to the ‘Health & Safety Notice located on page 3 of this
booklet before cleaning or replacing any refractory material.
The fuel bed components are delicate and they should be handled with great care.
The loose parts may be removed for cleaning. They can be brushed very gently with a soft
brush to remove dust or any deposits.
A vacuum cleaner may only be used after the loose components and moulded shapes have
been removed.
CARE SHOULD BE TAKEN TO AVOID CONTACT WITH THE REFRACTORY LINING THIS IS
A DELICATE SURFACE AND SHOULD NOT BE WIPED OR RUBBED.
FUEL BED LAYOUT (COAL OPTION)
Coal set provided consists of :-
6 off shape ‘A’ coals
12 off shape ‘B’ coals
1 off Left hand front coal matrix
1 off Right hand front coal matrix
1 off Base coal matrix
IMPORTANT: Keep the coals in separate groups
for laying on the fire bed.
Place the left and right hand front coals onto
the front of the burner tray as shown. The
front coals must be put on first because the
left hand coal is retained in place by the base
matrix.
Place the base matrix behind the front coals
as shown.
Pay special attention to make sure that the
burner slot is completely clear as shown
below.

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION THREE Fuel Bed Cleaning and Layout Cont.
Place the first row of 3 x A and 3 x B
overlay loose coals as shown between
the front coals and base matrix. Make
sure that they are stable and DO NOT let
them fall down in the gaps between the
peaks on the matrix.
Add 2 X A loose coal as shown.
Add 4 x B coals as shown.

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION THREE Fuel Bed Cleaning and Layout Cont.
Add 2 x type B coals and 1 x type A as
shown.
Add the final 3 x B coals as shown.
The layout is now finished.
Note: Dye is available for touching up coal and liner-board surfaces where the black colouring
may have rubbed off in use.

LT ())
UC Living Rosmore SLIDE CONTROL Users Instructions
SECTION FOUR Important Information
The only user removable parts are: -
The loose coals.
The baseboards
Cast Fret
Decorative Trim
Like all appliances incorporating an aerated burner a low frequency noise may be heard,
particularly on the low setting, this is quite normal and does not affect the operation of the
appliance.
Servicing
It is advised that the UC Living Rosmore fire is serviced annually this is more likely to provide
trouble-free operation. A competent person must carry this out, i.e. Gas Safe Registered
Installer in accordance with the current Gas Safety (Installation and Use) Regulations 1998 (as
amended).
The chimney or flue should be checked annually to ensure clearance of combustion products.
Ventilation in the United Kingdom
This appliance does not normally require purpose-built ventilation but if for any special reason
purpose-built ventilation is provided it should be checked periodically to ensure freedom from
obstruction.
Ventilation in the Republic of Ireland
Must be permanent ventilation and must comply with the rules in force and should be checked
periodically to ensure freedom from obstruction.
General Appliance Care
Any debris from the chimney or flue should be removed from the fuel bed. The fire should be
allowed to cool for three to four hours before removing debris.
Rubbish must not be thrown onto the fuel bed under any circumstances. The cast fire front must
be positioned in front of the fire whilst it is burning.
Fret (Fire Front)
A Fret must be used with this appliance, and
must conform too: -
It must be made from non-combustible
material.
Its general construction should enable it to
stand firmly across the full width of the
burner.
The design of the fire front (fret) must
have a removable ashtray cover (lower
section).
The ash tray cover must have cut-outs
and or holes which provide ventilation to the underside of the burner. The effective area of
ventilation through the ash tray cover must be greater than 1365mm2 (2.12 sq. ins.).


LT ())
UC Living Rosmore SLIDE CONTROL Installation Instructions
SECTION FIVE Specification
Natural Gas Propane Gas
Category of Appliance: BAS BAS
Category I2H I3P
Gas type: G20 G31
Gas Pressure: 20 mbar 37 mbar
Gas input high: 7.00 kW Gross 7.00 kW Gross
Gas input low: 2.40 kW Gross 2.40 kW Gross
Injector Main: Size 460 Size 135
Oxy-pilot SIT9040 SIT9221
Data Label Location: Frame of appliance on top RH corner behind trim
Gas Connection: 8 mm OD Tube
NOTE: The efficiency of this appliance has been measured as specified in BS7977-1 2009 and
the result is 63.4%. The gross calorific value of the fuel has been used for this efficiency
calculation. GASTEC have certified the test data from which it has been calculated. The
efficiency value may be used in the UK Government’s Standard Assessment Procedure (SAP)
for energy rating of dwellings.
SECTION SIX Regulations and Warnings
THIS APPLIANCE MUST ONLY BE INSTALLED IN THE GB OR IRELAND.
Only to be used in sufficiently ventilated room. Read instructions carefully before installation
and use. The appliance must be installed by a competent person, i.e.Gas Safe Registered
Installer in accordance with the current Gas Safety (Installation and Use) Regulations 1998 (as
amended). Failure to do so could lead to prosecution.
This UC Living Rosmore SLIDE CONTROL is for use ONLY with the GAS STATED ON
THE DATA BADGE this may be G20 for Natural Gas or G31 for Propane Gas.
CHECK YOU HAVE THE CORRECT APPLIANCE FOR THE GAS YOU ARE USING.
It can be used in conjunction with the following chimneys: -
A conventional brick or stone chimney,
A metal flue and box conforming to BS 715, further details are covered in later text.
A non-combustible hearth must be provided to comply with the building regulations or a
suitable proprietary fire surround with a 100 degrees C rating. During initial firing an odour
may be evident. This is the binder used during the manufacture of the fibre components and
there are no harmful effects produced.

LT ())
UC Living Rosmore SLIDE CONTROL Installation Instructions
SECTION SIX Regulations and Warnings Continued
The following are the relevant Codes of Practice and British Standards: -
BS 5871 BS 8303 1986
BS 5440 part 1 1990 BS 1251 1987
BS 6891 1988 BS 6461 parts 1 & 2 1984
BS 715 1989 BS 1289 part 1& 2 1986
Note:- This appliance must be installed to current versions of the above standards and
include any relevant amendments.
The Building Regulations issued by the Department of the Environment
The Building Standards (Scotland) (Consolidation) Regulations issued by the Scottish
Development Office.
SECTION SEVEN Siting the Appliance
The fire can be installed in the following flues and locations: -
CLASS ONE
A conventional brick or stone chimney as used for a solid fuel appliance with a typical effective
cross-sectional dimension of 225 x 225 mm (9 x 9 ins) or a lined flue with a minimum diameter
of 125 mm (5 ins) .This includes Pre-cast flue systems.
Note: The restrictor plate (fitted to the fire) may be left upright in flues of 175mm (7") or
greater. This being subject to satisfactory products clearance.
Fireplace opening must be 560 mm - 580 mm high by 400 mm –456 mm wide.
The opening depth must be a minimum of 320 mm to allow sufficient volume for debris
collection.
To obtain this depth it may be necessary to remove the chair brick.
Any permanent flue restriction or variable dampers are to be removed or locked fully open. The
chimney should be swept prior to installation if not new