Uclear HBCR001 User manual

Universal Remote User Manual
Make sure your HBC unit is updated with the latest firmware
which can support your Universal Remote.
HBCR001
FCC ID:NMCHBCR001

EN 1
Contents
Contents --------------------------------------------------------------
Quick User Guide --------------------------------------------------
Warnings and Safety Instructions ------------------------------
Features --------------------------------------------------------------
Kit Includes ---------------------------------------------------------
Installation ------------------------------------------------------------
General Operaions --------------------------------------------------
Intercom Connection -----------------------------------------------
General Button Configurations -----------------------------------
General Status Indicator Configurations ----------------------
Technical Data ------------------------------------------------------
Notices ----------------------------------------------------------------
1
2
6
7
8
9
11
14
18
19
20
21

EN 2
Quick User Guide
General Functions and Layouts
Button functionality is identical to HBC Unit.
For more complete instructions, please refer to your HBC Series User Manual.
Velcro Hook
DFU/
Charging Socket
‘Power’/
‘Answer’ Button
Vol ‘Up’ Button
Vol ‘Down’ Button
LED Indicator
Back view Front view
Pairing with HBC unit
1.
seconds until LED blink blue and red alternatively.

EN 3
Attention:
If pairing or Just Connect Mode fails, the Universal Remote will be turned
off automatically. If fails, redo step 1 and 2.
Quick User Guide
1. Make sure the ‘Power’ for the paired HBC unit is on.
2. Power on Universal Remote by pressing the ‘Answer’ button once, it
will connect to the paired HBC unit automatically.
OR
2. While holding the ‘Up’ or ‘Down’ button, power ‘On’ the Universal
Remote, only release the ‘Up’ or ‘Down’ button until the LED blinks
blue and red alternatively.
Just Connect Mode
It is only necessary to do the pairing for the first time. After pairing with
your unit, your Universal Remote will connect automatically to your paired
unit once you power on your device.

EN 4
Power On
Press the ‘Power’ button once, the Universal Remote will be turned on.
Power Off
The Universal Remote will be turned off automatically once the paired HBC
unit is off.
Reset
Connected Micro USB cable to the computer USB port or power sources.
Plug in and plug out the micro USB cable from Universal Remote.
Battery Low
LED indicator will appear blinking red every second to indicate that the
battery is low, hence charging is required.
Charging
Insert the Micro USB charger to the Universal Remote DFU/ Charging Socket.
> Solid red LED will appeared while charging.
> Solid blue LED will appeared when fully charged.
DO NOT PRESS on any buttons while plugging in. It may cause the device to
Quick User Guide

EN 5
Quick User Guide
Firmware Update
1. Download and install the new version software from UCLEAR website.
support your Universal Remote.
2. Connected securely the USB cable to the computer USB port.
3. Powered off the Universal Remote by holding ‘Up’ and ‘Down’ buttons
at the same time.
4. Insert the Micro USB to the Universal Remote DFU/ Charging Socket.
5.
++
+

EN 6
This manual uses the and icons to highlight certain instructions.
Below is an explanation of the icons.
Attention
This icon highlights special instructions and precautions intended to avoid
damage to the system. Non-compliance may void the product warranty.
Attention
Please read through the operating instructions to understand how to operate
the system, in particular the safety instructions.
Warning
This icon provides precautions important to prevent injuries to the user.
Warning
sProlonged exposure to loud sounds may lead to permanent hearing
damage.
sSpeaker volume is greater than 90dBm may lead to permanent hearing
damage.
sDo not attempt to place an outgoing call through the mobile phone
while riding on the motorcycle at any point of time.
sPlease do not use the Universal Remote in anyway that may distract
you or hinder your judgment while on the move. Never ever compromise
your safety and the safety of others.
Warning and Safety Instructions
!
!
!

EN 7
Attention
Charging and handling rechargeable battery products incorrectly may cause
instructions below:
sNever change the batteries yourself, always bring the device to an
authorised dealer to perform the replacement for you.
sWhen charging, use ONLY the charging cable provided or replacement
cable from the UCLEAR dealer. Using similar, compatible or any
other cables may lead to permanent product damage and will void the
product warranty.
s
Remote in any way as it may cause the system to malfunction causing
hurt to you.
Warning and Safety Instructions
Features
The UCLEAR Universal Remote is a convenient and safe alternative or
replacement for the 3 buttons on Helmet Communicator.
sCompatible with product series (HBC200, HBC100+, and future
product series)
sFirmware upgradable
sRechargeable battery
sVersatile mounting mechanism
sWeather resistant
sAuto shut down
!

EN 8
Kit Includes
1 Velcro Strap
(150mm long)
1 Micro USB Charger
(1m long)
Universal Remote Package Contains:
1 Universal Remote
1 Quick Start Guide
Universal Remote
Quick Start Guide

EN 9
1. Place the Velcro strap near to the handle bar.
(As per illustration above)
2. Loop the Velcro strap around the handle bar.
Installation

EN 10
3. Place the Universal Remote onto the Velcro strap.
Installation
4. Ensures the Universal Remote is fastened.
Installation completed. Enjoy!

EN 11
General Operations
Your UCLEAR Universal Remote is now all set and ready to go!
Universal Remote to HBC, HBC to Mobile Phone
Establish connection between Universal Remote and HBC:
sPower ‘On’ the HBC unit, hold ‘Up’ and ‘Down’ buttons for seconds
until LED blinks blue and red alternately.
sWhile holding the ‘Up’ or ‘Down’ button, power ‘On’ the Universal
Remote, only release the ‘Up’ or ‘Down’ button until the LED blinks
blue and red alternately.
sOnce the connection is successful, HBC unit and Universal Remote
will blink blue.
s
Mode is a more convenient way of establishing connection between
HBC unit and Universal Remote.

EN 12
Establish connection between HBC and Mobile Phone
sHold the ‘Up’ and ‘Down’ buttons on the HBC unit for 2 seconds.
sThe LED indicator would blink blue and red alternately.
sTurn on the mobile phone bluetooth and select the respective UCLEAR
HBC name to pair with the unit.
When prompted to enter a passcode, enter ‘0000’.
*Most mobile phones when paired would be automatically connected with
both phone and music bluetooth capabilities.
All the connections among Universal Remote, Helmet Communicator, and
Mobile Phone are established. You may now use the Universal Remote to
control the helmet communicator to answer your calls, make outgoing calls
or listen to music.
General Operations

EN 13
Pick up incoming call:
Press the Universal Remote ‘Answer’ button once.
Reject calls:
Hold the Universal Remote ‘Answer’ button for 2 seconds.
Voice calls:
Hold the Universal Remote ‘Down’ and ‘Answer’ buttons for 2 seconds.
Last number redial:
Hold the Universal Remote ‘Up’ and ‘Answer’ buttons for 2 seconds.
Play music
Press the Universal Remote ‘Answer’ button for 2 times.
Stop music
Press the Universal Remote ‘Answer’ button 1 times.
Fast forward music
Press the Universal Remote ‘Up’ button for 2 times.
Back track music
Press the Universal Remote ‘Down’ button for 2 times.
Attention
Please DO NOT HOLD the Universal Remote ‘Answer’ button for too long
while rejecting calls. It may turn off the connected HBC unit ( 5 seconds will
turn off the connected HBC unit), unless you want to turn it off.
General Operations

EN 14
Intercom Connection
Attention
Pairing is only necessary for establishing your initial connection. You can use
Just Connect Mode to establish future connections between your Universal
Remote and HBC controller.
Step 1
Pair the Universal Remote to respective HBC unit, if they have not been
paired before.
To connect the Universal Remote to the helmet communicator,
sPower ‘On’ the HBC unit and hold ‘Up’ and ‘Down’ buttons for 2
seconds until LED blinks blue and red alternately.
sWhile holding the ‘Up’ or ‘Down’ button, power ‘On’ the Universal
Remote, only release the ‘Up’ or ‘Down’ till the LED blinks blue and
red alternately.
sOnce the connection is successful, HBC and Universal Remote will
blink blue.
sPower ‘Off’ the Universal Remote and respective HBC unit. The
Universal Remote to the respective HBC unit preparation is done.

EN
Or More...
Unit 1 Unit 2 Unit 3 Unit 4
Step 2
Pairing between HBC units.
other HBC units.
Pairing process needs to be carried out only once.
s
sPick one units as the 1st device, hold ‘Answer’ and ‘Up’ buttons for 3
seconds.The status indicator wouldblink purple.
sFor the 2nd device, hold ‘Answer’ and ‘Up’ buttons for 3 seconds. The
status indicator wouldblink purple. Wait until the 1st device status
indicator to turn blue, then proceed to pair the next device.
sHold ‘Answer’ and ‘Up’ buttons for 3 seconds on the 3rd device.
The status indicator will blink purple. Wait for the 2nd device status
indicator to turn blue, then proceed to pair the next device.
sRepeat all steps for all other units until all the devices are paired.
sThe last device will remain blinking purple if the maximum HBC that
can be connected have not been reached. You can press any button on
the device toend the pairing process. The status indicator will turn blue.
sOff all the HBC units and the preparation is done.
Intercom Connection
15

EN
Or more…
16
The time of in use
Step 2
Turn ‘On’ all HBC units, connecting up all the intercom.
To enable the intercom, hold the ‘Up’ button for 2 seconds. All the paired
HBC units will be chained up automatically.
Step 3
Connect respective Universal Remote by pressing ‘Power’ button once.
(Turning ‘On’ the power, the Universal Remote will connect to the already
paired HBC units).
Step 4
Connect the Phone to HBC device if phone is used
sIf the phone is paired with the respective HBC unit, turn on the mobile
phone bluetooth functions, select the UCLEAR HBC device name to
connect.
Or more…
Or more…
Intercom Connection

EN 17
sIf the phone has not paired with the respective HBC unit yet, pairing
is necessary by holding the ‘Up’ and ‘Down’ buttons of the Universal
Remote for 2 seconds. This will let the helmet communicator into
pairing mode. The status indicator ofthe HBC unit would blink blue
and red alternately.
sNext turn on the mobile phone bluetooth functions and search for
bluetooth devices. Select the UCLEAR HBC device name to pair with
the desired device.
sMost mobile phones when paired would be automatically connected
with both phone and music bluetooth capabilities.
Or more…
Intercom Connection

EN 18
Action Button
Not Connected
Power on Press ‘Answer’ button once
Pairing While holding ‘Up’ or ‘Down’ button, on the
‘Power’
Connected to HBC (HBC connected to phone)
Activate HBC pairing Hold ‘Up’ and ‘Down’ buttons for 2 seconds
Reset HBC Press ‘Answer’, ‘Up’ and ‘Down’ buttons
simultaneously
Pick up call Press ‘Answer’ button once
End call Hold ‘Answer’ button for 2 seconds
Reject call Hold ‘Answer’ button for 2 seconds
Voice dial Hold ‘Answer’ and ‘Down’ buttons for 2 seconds
Last number redial Hold ‘Answer’ and ‘Up’ buttons for 2 seconds
Play music Press ‘Answer’ button 2 times quickly
Stop music Press ‘Answer’ button 1 time
Fast forward track Press ‘Up’ button 2 times quickly
Backtrack Press ‘Down’ button 2 times quickly
Connected to HBC (Intercom is used)
Connect intercom Hold ‘Up’ button for 2 seconds
Disconnect intercom Hold ‘Down’ button for 2 seconds
Common instruction commands (For phone call, music, intercom)
Volume Up Press ‘Up’ button once
Volume Down Press ‘Down’ button once
General Button Configurations

EN
General Status Indicator Configurations
The table below shows the status indicator configurations
19
State Status Indicator
1Power on (No connection) Blink purple once every second
2Pairing to HBC unit Blink blue and red alternatively slowly
3Connecting to HBC unit Blink blue and red alternatively quickly
4Connected to HBC unit Blink blue slowly once every 2 seconds
5Battery low Blink red every minute
6Power off Blink red 5 times
7Battery charging Solid red
8Battery fully charged Solid blue
9Entering DFU mode Blink red once (All LED off completely)
10 Power off All LED off