Udizine Vertik User manual

Assembly Instructions

General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended

weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE

is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.

VER_01

Vertik

Floor Stand

Page 1 of 4

24”26”

24 1/2 ”

56 1/4"

4 1/2”

3/4”1 1/2”

3/4”

Slits Required Shelf Length:

23 7/8”

include edge banding

Hardware Provided Base Add-On

Socket Head Screw L 1 1/4” & Washers 4 2

Flat Head Screw 4 —

Allen Key Set- Metric # #5 & #6 #4 & #6

Wrench for M10 washer 1 1

L 1 5/8”

Extension Bar Connecting Set — 2

B2 E2

Base Unit Add-On Unit

Screw

thread on

both ends

For base unit only - see page 2

For multyple units (UP TO 3 UNITS) - see page 3

Screw

thread

on one

end only

Casters

Assembly Instructions

General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended

weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE

is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.

VER_01

Vertik

Floor Stand

Page 2 of 4

Base Unit Assembly

Assemble Part B1 to Parts B2 and tighten screws. NOTE: Place Parts B2 in the correct direction as illustrated

**Note: when assemble multiple unit please see page 3 for instruction**

FACE

OUT FACE

Narrow side up

Assemble Part B3 to

B1 with screws and

tighten.

Fasten casters to

Parts B3.

Assemble Part B1 to Parts B1 & B2. Tightening screws

Accessories Assembly

Slide into slits at

the desired height

Slide down with a little

pressure.

Note: make sure its fully

inserted into position.

Each slit can hold

two accessories

Assembly Instructions

General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended

weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE

is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.

VER_01

Vertik

Floor Stand

Page 3 of 4

Multiple Units Assembly (Up to 3 units per stand)

Assembled Parts E2 to B1.

Note: Direction of Parts E2 as illustrated. Fasten screws.

Assemble Part E1 to Parts B2 with “Extension Bar Connecting Set” at top and

bottom, as illustrated. Fasten screws

Attached E2 to E1 at top and bottom. Fasten screws on E2 Assemble Parts B3

and E3 with screws

as illustrated and

tighten.

Fasten casters to

Parts B3 and E3.

B1 B1

B2 B2

Base

Add-On

Assemble Part B1 to Parts B2 and tighten screws

NOTE: Place Parts B2 in the correct direction as illustrated

Narrow side up

IN & OUT

Hole

face

down

Hole

face

down

Hole

face

Hole

face

FACE

OUT FACE

Sides Middle 1

Assembly Instructions

General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended

weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE

is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.

VER_01

Vertik

Floor Stand

Page 4 of 4

Accessories

Max Weight Load

Shelf

Required Shelf Width:

23 7/8” include edge banding

Shelf Type & Thickness:

Signage

Sign Width: 23 7/8”