UFO LD10 User manual

LED Type Oslon Square
LED Power 1W @ 350mA
Power Connecon 2 pin Molex
Colour Temp, CRI
& Lumens Opt. 1
2700K, 61 lm/w
>98 CRI
Colour Temp, CRI
& Lumens Opt. 2
3000K, 65 lm/w
>98 CRI
Colour Temp, CRI
& Lumens Opt. 3
4000K, 72 lm/w
>97 CRI
Lens Opons 13.5° / 19° / 28°
LED Life >54,000h
Operang Environment IP66 rated for use in indoor/dry
or outdoor/wet areas
Min. Ambient Temperature 10°C
Max. Ambient Temperature +40°C
Material 316 stainless steel
Max Fing Cable Length
(28AWG) 10m (32.8’)
Notes:
Maximum cable length is defined by no discernable reduction
in light output.
*500mA variant not for use in USA or Canada
LD10 Articulated LED Downlight
TECHNICAL SPECIFICATIONS
Continuity
Jumpers
Low Voltage
Cable
NOTE
ALL unused inputs
on the 12 Way
Splitter must be
terminated with a
Continuity Jumper
to ensure series
circuit is not
broken.
12 Way Series
Splitter
Outputs 1-6
Outputs 7-12
12 Way Series
Splitter
Outputs 1-6
Outputs 7-12
LED CONSTANT CURRENT DRIVER
LED
Driver
O/P
LED CONSTANT CURRENT DRIVER
LED
Driver
O/P
Basic 7 Channel system shown as an example. The remaining 5 unused inputs must be
terminated for the LEDs to light up
Continuity
Jumpers
LED fittings
SPLITTER SPCC1 LED fittings
Series splitters are used to connect multiple Led fittings to the constant current driver
350mA Constant
Current
These LED fittings are CONSTANT CURRENT only
NEVER – hot swap LEDs
NEVER – connect less than the minimum or more than the maximum number of LEDs as
specified by the d river
IMPORTANT
LD10 Articulated LED Downlight
Schematic Showing Driver & Splitter
UFO Licht GmbH
Andreasstraße 20
93059 Regensburg \ Deutschland
[phone] \www.ufo-licht.de
Universal Fiber Optic Lighting USA, LLC
1749 Northgate Blvd
Sarasota \FL34234 \USA
941-343-8115 \www.fiberopticlighting.com
Universal Fibre Optics Ltd
Home Place \Coldstream
TD12 4DT \UK
[phone] \www.ufo.lighting
Please read the user guide carefully before installing, operating
or performing maintenance on these devices.
QUICKSTART GUIDE
UFO LD10 LED DOWNLIGHT
Rev. C1
Problem Probable Causes Test & Remedy
Constant Current System
System is dead - no light
output from LED’s
Mains supply o Check supply and reinstate.
Loose mains plugs Check plugs.
Loose DC output wire or
connection Check all connections.
Splitter LED channel not
terminated
Check all splitter channels have LED
fittings plugged in or have continuity
jumpers fitted. Plug in LED’s and/or jumpers
Single failed LED
With power ON, carry out one of tests
detailed in fault finding guide. Replace
faulty LED.
More than one failed LED
Gradually replace LED plugs with
continuity jumpers until LED’s light. Do
not reduce the number of LED’s plugged
into the splitter below the driver minimum
Driver failed
Check output with DVM. With power ON
and no LED’s lit, DC voltage output to
LED’s should be at maximum
Cable between driver and
splitter failed
With power ON and splitter cover
removed, put DVM across input to splitter.
DC voltage input to splitter (allowing for
volt drop in cable) should be at
maximum. If no voltage fault find and/or
replace cable.
Constant Current System
Some LED’s not working
Short circuit - damages cable
between LED and splitter Repair or replace.
LED short circuit Replace LED and cable.
Constant Current System
LED’s on full illumination
- not dimming
Faulty or wrong connection at driver
or dimmer control box
Check driver and dimmer connections.
Replace/repair as necessary.
Faulty dimmer potentiometer or
damaged dimmer control cable
Remove dimmer control cable from
dimmer. Check continuity of cable and
dimmer pot. Replace/repair as necessary.
Failed driver Replace driver.

WARNING – Connecting constant current LED fittings to a driver with excessive
minimum voltage output will result in catastrophic damage to the LED devices
within these fittings. Always check the minimum output voltage of the driver and
ensure that based on 3.2V per LED an adequate number of fittings are connected
prior to powering up the system.
WARNING – Hot swapping constant current LED fittings to a driver may result in
catastrophic damage to the LED devices within these fittings. Always power down
the driver before adding a constant current LED fitting.
These LED fittings are IP66 rated and are suitable for use in both indoor/dry areas
and in damp or wet conditions.
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT, ITS COMPONENT PARTS AND THE HAZARDS
INVOLVED.
ELECTRICAL WIRING AND CONNECTION MUST BE CARRIED OUT BY A SUITABLY
QUALIFIED PERSON OBSERVING ALL LOCAL AND STATUTORY ELECTRICAL
REGULATIONS.
LD10 Articulated LED Downlight
Safety Guidelines
LD10 Articulated LED Downlight
Connections
The fittings are suitable for use with a constant current driver only.
• 350mA or 500mA output (depending on territory)
• Rated Class 2 or LPS
• Approvals UL/CE
• Protection - Short Circuit/Over load/ Over voltage
• Minimum voltage rating not to exceed the number of LED fittings connected
• Number of LED fittings connected not to exceed the Maximum voltage rating
There are 4 electrical connections required before connecting the system to the
mains.
1. Connect ALL LED fittings to the input channels of the Series Splitter.
2. Make sure ALL unused Series Splitter channels have continuity link jumpers
fitted
3. Connect the Series Splitter directly to the Constant Current Driver.
4. Connect the electrical supply to the driver. Switch on power, the LED fittings will
illuminate.
If no light is produced, consult the TROUBLESHOOTING section.
2 4
LD10 Articulated LED Downlight
LD10 Fitting Guide
LD10 Articulated LED Downlight
Introduction
Thank you for purchasing these low voltage UFO LED fittings.
Please read these instructions fully before installing your LED fittings, connecting
your LED fittings to the splitter/driver and before connecting your display system to
the electrical mains. Please keep this manual for future reference.
The UFO splitters are supplied with removable continuity jumpers. Retain these
jumpers for future use.
Please refer to the specific section within this manual to ensure correct associated
splitters/drivers/power supply units are used for your fittings.
These LED fittings are only mains dimmable with an appropriate mains dimmable
constant current driver.
These LED fittings operate on a constant current driver low voltage supply.
Constant current and constant voltage LEDs cannot be intermixed on the same
driver. Please refer to the specific section within this guide for wiring/connection
guidance.
1 3
LD10 Downlights are constant current LED fittings.
Before assembly, unpack the shipment and check that all components are included
before commencing your installation. It is recommended that the system be planned
prior to work commencing to ensure the Series Splitter is centrally located to match
LED fitting cable lengths. Fit all LD10 fittings in place as detailed below.
NOTES
Don’t cut the hole too big
Take care not to trap wires
LD3 Articulated Fitting
53mm
1.0
Cut hole in
mounting
surface
2.0
Thread cable
through hole
3.0
Fold back
springs and
push LED
Fitting through
the hole
4.0
Push LED
Fitting all
the way in
5.0
Adjust LED
Fitting to
required angle