UKIAH TAILGATER II User manual

WWW
.UKIAHCO.
COM
TAILGATER II
MANUAL
TK-1044-T2BLK 7 2802850224 4
TK-1006-T2 7 2802848232 4

2
DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
Shut off gas to appliance.
Extinguish any open ame.
If odor continues, leave the area immediately.
After leaving the area, call your gas supplier or re department.
Failure to follow these instructions could result in re or explosion,
which could cause property damage, personal injury, or death.
WARNING
Do not store or use gasoline, or other ammable vapors and
liquids, in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the
vicinity of this or any other appliance.
WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualied installer,
service agency, or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING: If the information in this manual is not followed
exactly, a re or explosion may result causing property damage,
personal injury, or loss of life.
The appliance when installed, must be electrically grounded in
accordance with local codes, or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70; or the Canadian
Electrical Code, CSA C22.1, if applicable.
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space
such as a camper, tent, car or home.

3
SAFETY INFORMATION
WARNING
Please read these setup and operating instructions carefully before setup, operation or service of this gas re pit. Do
not operate if you are uncertain as to the meaning of any instructions or warnings. Improper installation, adjustment,
alteration, maintenance, service or use of this product may result in property damage, personal injury or the potential
loss of life.
Save these instructions for future reference. If you are assembling this unit for another person, give this manual to the
re pit operator to read and save for future reference. If ownership of the product is transferred, this manual should be
provided to the new owner.
This product is designed to use Liquid Propane fuel only. Do not attempt to use natural gas as a fuel. ONLY OUR HOSE
AND REGULATOR SUPPLIED IN THE PACKAGING CAN BE USED WITH OUR FIRE PITS.
Failure to follow the DANGERS, WARNINGS, AND CAUTIONS in this owner’s manual may result in serious bodily injury,
death, or may result in a re or an explosion causing damage to property.
WARNING: This product is for outdoor use only.
WARNING: Do not use this product near vegetation or on, under, or near structures that could catch re such as
wooden decks, vinyl siding, or porches with overhangs.
WARNING: This product produces high temperatures that will create hot surfaces. Appropriate care should be used
to avoid physical contact with these surfaces.
WARNING: Do not use this product during windy conditions.
WARNING: This product should be used on a at and stable surface to avoid overturning.
WARNING: Do not leave unattended when in use or connected to a fuel supply.
WARNING: This product includes small components such as glass crystals that may pose a choking hazard or cause
signicant physical injury if swallowed. Appropriate care must be taken to prevent children from having unsupervised
access to this product or any of its components.
WARNING: Maintenance or service on this product must be performed by a qualied installer or licensed service
professional.
WARNING: DO NOT move the unit for at least 60 minutes after use to allow for cooling.
WARNING: Allow the burner and glass crystals or lava rock to cool completely before touching.
WARNING: Glass crystals or Lava rock may be sharp. Before handling, make certain they have cooled completely
and handle them wearing protective gloves to prevent injury.
WARNING: This device can produce carbon monoxide that has no odor. Never use in an enclosed space of any
kind, including but not limited to the inside of a home, garage or building. Use in such an enclosed space can be
potentially fatal.
WARNING: After a period of storage or non-use, check for leaks and burner obstructions.
WARNING: Do NOT attempt to disconnect the gas regulator from the cylinder or any gas tting while the re pit is
in use.

4
WARNING: Do NOT attempt to move re pit when in use.
WARNING: Always keep children and pets away from re pit.
WARNING: Never lean over the re pit when lighting or in use.
WARNING: Do NOT attempt to repair or alter the pressure regulator for any assumed defect. Any modication to
this assembly will void your warranty and create the risk of a gas leak and re.
WARNING: This re pit should be thoroughly cleaned and inspected on a regular basis.
WARNING: Do NOT use the re pit unless it is COMPLETELY assembled, and all parts are securely fastened and
tightened.
WARNING: Do NOT use in an explosive atmosphere.
WARNING: Do NOT store or use gasoline or other ammable liquids or vapors within 25 feet (7.62 m) of this
appliance.
WARNING: Recheck all connections as described in the “Operating Instructions” section of this manual, as shipping
can loosen connections.
• Check for leaks even if your unit was assembled for you by someone else.
• Do NOT operate if a gas leak is present. Gas leaks may cause a re or explosion.
• You must follow all instructions in the “Checking for Leaks” section before operating.
WARNING: To prevent a re or explosion hazard when testing for a leak:
• Always perform a leak test before lighting the re pit and each time the cylinder is connected for use.
• No smoking. Do NOT use or permit sources of ignition in the area while conducting a leak test.
• Conduct the leak test outdoors in a well-ventilated area.
• Do NOT use matches, lighters, or a ame to check for leaks.
• The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or
safely operate the appliance.
• Strong odors, colds, sinus congestion, etc. may prevent the detection of propane. Use caution and common sense
when testing for leaks.
• Do NOT use re pit until any and all leaks are corrected. If you are unable to stop a leak, disconnect the LP gas supply.
Call a gas appliance serviceman or your local LP gas supplier.
WARNING: Never keep an LP gas cylinder in a hot car or trunk. Heat will cause the gas pressure to increase, which
may open the relief valve and allow gas to escape.
WARNING: Do NOT block holes in sides or bottom of re pit.
WARNING: Apartment dwellers: Check with management to learn the requirements and re codes for using a LP
gas re pits in your apartment complex.
WARNING: This re pit is not intended for and should never be used as a heater. TOXIC fumes can accumulate and
cause asphyxiation.
WARNING: ELECTRONICS INSIDE, MUST PUT COVER ON UNIT WHEN LEAVING OUT IN WET CONDITIONS.
DANGER: Do not use the product if any part has been submerged in water. Immediately call a qualied service
technician to inspect the unit and to replace any part of the control system and any gas control that has been in water.

5
WARNING: Special care must be taken to keep children and pets away from hot surfaces.
WARNING: Deaths, serious injury or damage to property may occur if the above is not followed exactly.
DANGER - If you smell gas fumes:
1. Shut off gas to the appliance by turning the fuel knob to “OFF” and turn LP tank off.
2. Extinguish any open ame. Do not touch or make contact with any electrical switches.
3. Do not ignite a match or lighter of any kind.
4. Do not use any phone, including cell phones, in the vicinity of the gas source.
5. If the smell of fumes persists, call the local re department from a remote phone.
Failure to follow these instructions could result in re or explosion which could cause property damage, personal injury,
or death.
WARNING
•Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any other appliance.
• An LP cylinder not connected for use should not be stored near this or any other appliance.
•If a re should occur, keep away from the appliance and immediately call your re department.
Failure to follow these instructions could result in re, explosion or burn hazard, which could cause property damage,
personal injury or death.
The LP gas tank is NOT included with the gas re pit.
SAFE HANDLING FOR LP GAS TANK:
• Do not use a damaged, dented or rusty LP tank.
• Handle empty LP tanks with the same care as you handle full tanks. Even when the LP tank is empty of liquid, there
may still be gas pressure inside the cylinder.
• LP gas tanks should never be dropped or handled roughly.
• Never store or transport the LP tank where temperatures can reach 125 °F (51.7 °C).
• LP tanks must be kept out of reach of children.
WARNING
• DO NOT block any ventilation openings.
• Install in accordance with the manufacturer’s instructions.
• DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the
third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
• PROTECT the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
• ONLY USE attachments and accessories specied by the manufacturer.
• UNPLUG this apparatus during lightning storms or when unused for long periods of time.
• REFER all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus.
• DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or re.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• DO NOT ingest the battery.
• Keep new and used batteries away from children.

6
60 in / 152.4cm
WARNING
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical
attention.
• The battery (battery, batteries or battery pack) shall not be exposed to excessive heat such as sunshine, re or the
like.
• DO NOT handle leaking or damaged batteries.
• Only use the specied type of Batteries.
• Observe correct polarity.
• Remove batteries from products that are not in use for extended periods of time. Store batteries in a dry place.
• Do not recharge non-rechargeable batteries.
• Avoid exposure to extreme heat or cold.
• THIS PRODUCT CONTAINS A CELL BATTERY. IF MISUSED OR ABUSED THIS CAN RESULT IN:
-Smoke or gas hazard -Heat hazard -Fire hazard -Explosion hazard
WARNING
Keep out of reach of children. The content of this package includes small parts and cords that can cause choking or
strangulation.
WARNING
Fuels used in gas or oil-red appliances, and the products of combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects or other reproductive harm. This warning is issued pursuant to
California Health and Safety Code Sec. 25249.6.
PROPOSITION 65 WARNING: Handling the brass material on this product exposes you to lead and lead
compounds, a chemical known to the state of California to cause cancer, birth defects or other reproductive harm.
WASH YOUR HANDS AFTER HANDLING THIS PRODUCT. For more information go to www.P65Warnings.ca.gov

7
PRODUCT DIAGRAM
TANK STAND ASSEMBLY

8
WELCOME TO THE UKIAH Co. FAMILY
Based in the Pacic Northwest, Ukiah Co. was founded with a mission to offer the world
products never before seen in the outdoor living market. Our goal is to offer affordable,
top quality outdoor entertainment with unique and trend-setting styles that bring people
together. Mankind has always been deeply connected to the outdoors, companionship and
music; we develop products that embody these natural fundamentals of life. Wherever your
adventures may nd you, Ukiah Co. offers a diverse entertainment product line to enhance
your outdoor experience at home or on the go. Our audio-capable products transform
outdoor living spaces and enhance your favorite activities that will change the way you enjoy
the outdoors.
CONGRATULATIONS ON YOUR BLUETOOTH® FIRE SPEAKER PURCHASE
Take your outing to the next level with the most versatile portable re pit on the market with
2.1 crystal clear sound with patented BEAT TO MUSIC FIRE TECHNOLOGY.
Connect by Bluetooth® and enjoy the highest quality audio with re ambiance anywhere
you want to be. Featuring a 2.1 sound system and custom-designed “RESPONSIVE FLAME
TECHNOLOGY”. The upgraded 2.1 audio system consists of two 3.5 inch speakers and
one subwoofer for incredible sound quality. “BEAT TO MUSIC” mode synchronizes ame
to music with our custom “REACTIVE FLAME TECHNOLOGY”. Dancing ames harmonize
perfectly with music for amplied entertainment.
IGNITE THE MUSIC™

9
TABLE OF CONTENTS
SAFETY INFORMATION // PAGE 3
PRODUCT DIAGRAMS // PAGE 7
GENERAL INFORMATION // PAGE 10
LEAK TESTING // PAGE 11
LIGHTING SAFETY // PAGE 12
BEFORE USE // PAGE 13
SETUP INSTRUCTIONS // PAGE 14
LIGHTING INSTRUCTIONS // PAGE 15
AUDIO SYSTEM // PAGE 16
BEAT TO MUSIC OPERATION // PAGE 17
MAINTENANCE & STORAGE // PAGE 18
TROUBLE SHOOTING // PAGE 19
WARRANTY // PAGE 20
By purchasing this unit, you agree to follow all startup and safety instructions. You also agree that this
product will not be used for any other reason as it was intended. Any questions or comments about
our product, please click the “Contact us” link at www.UkiahCo.com

10
GENERAL INFORMATION
• This device can produce carbon monoxide that has no odor. Never use in an enclosed space of any kind, including
but not limited to the inside of a home, garage or building. Use in such an enclosed space can be potentially fatal.
• Make certain that the outdoor area in which the product is being used offers acceptable cross ventilation.
• Gas cylinders must be stored outdoors in a well-ventilated area, out of the reach of children. Disconnected cylinders
must have threaded valve plugs tightly installed and must not be stored in a building, garage or other enclosed area.
• Check with your local re safety authority if you have any questions about the use or operation of portable gas
cylinders or this gas re pit.
• Operator should inspect the product before each use. It should be inspected at least annually by a qualied service
technician. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burner
and circulation air passageways of the unit are kept clean and free of debris.
• If it is evident that there is excessive abrasion or wear on any of the components, they must be replaced prior to the
product being put into service. Contact us at www.UkiahCo.com.
• The operator of this gas re pit should alert adults and children to the hazards of high surface temperatures and the
danger of burns or clothing ignition. Adults and children should maintain a reasonable distance from the open ame
and hot surfaces. Flammable materials should not be placed near the re pit.
• Flame heights can change suddenly. Never pass objects over the unit. Never place objects on top of the re pit.
Never reach over re pit assuming the ame will remain at its “Low” setting.
• Always turn unit off after use.
• Young children should be closely supervised when near the product. Do not leave this gas re pit unattended,
especially around children or pets.
• Solid fuels such as wood, paper, or trash should not be burned in this gas re pit. This product is designed for
decorative purposes only, and should not be used for heating, cooking, or drying.
• Do not attempt to assemble or operate this re pit while under the inuence of any type of alcohol or medication.
Use this gas re pit in accordance with all applicable local, state, and national codes.
• Any guard or protective device removed in order to service the device must be replaced prior to operating the re
pit.
• Inspect the fuel supply for evidence of leakage prior to each use of the re pit. The pressure regulator and hose
assembly supplied must always be used.
• The 20 lb. gas cylinder must be constructed and marked in accordance with the specications for Liquid Propane-
Gas cylinders as required by the U.S. Department of Transportation (DOT) or the Canadian Transportation Commission
(CTC).
• The 20 lb. gas cylinder used must include a collar to protect the cylinder valve.
• When the unit is not in use, the gas supply must be turned completely off using the valve on the cylinder tank.

11
LEAK TESTING
LEAK TESTING:
All factory-made connections have been thoroughly tested for gas leaks. However, shipping and handling may have
loosened a gas tting.
AS A SAFETY PRECAUTION:
• TEST ALL FITTINGS FOR LEAKS BEFORE USING YOUR GAS FIRE PIT.
• TEST THE CYLINDER VALVE FOR LEAKS EACH TIME THE CYLINDER IS FILLED.
• TEST FOR LEAKS EVERY TIME YOU CONNECT A GAS FITTING.
• DO NOT SMOKE WHILE TESTING FOR LEAKS.
• NEVER TEST FOR LEAKS WITH A LIGHTED MATCH OR OPEN FLAME.
• TEST FOR LEAKS OUTDOORS.
DANGER: Do NOT use an open ame to check for gas leaks. Be sure there are no sparks or open ames in the
area while you check for leaks. Sparks or open ames will result in a re or explosion, which could result in serious
bodily injury or death and damage to property.
WARNING: To prevent a re or explosion hazard when testing for a leak:
• Always perform a leak test before lighting the re pit and each time the cylinder is connected for use.
• No smoking. Do NOT use or permit sources of ignition in the area while conducting a leak test.
• Conduct the leak test outdoors in a well-ventilated area.
• Do NOT use matches, lighters, or a ame to check for leaks.
• The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or
safely operate the appliance.
• Strong odors, colds, sinus congestion, etc. may prevent the detection of propane. Use caution and common sense
when testing for leaks.
• Do NOT use re pit until any and all leaks are corrected. If you are unable to stop a leak, disconnect the LP gas supply.
Call a gas appliance serviceman or your local LP gas supplier.
TO TEST FOR LEAKS:
1. Extinguish any open ame or cigarettes in the area.
2. Check the cylinder valve and appliance valves are in the “OFF” position.
3. Connect LP gas cylinder.
4. Prepare a soap solution of one-part water, one-part liquid detergent.
5. With a full gas cylinder, open cylinder slowly.
6. Brush the soap solution on each connection and along the hose.
7. A leak is identied by a ow of bubbles from the area of the leak.
8. If a leak is detected, close the gas cylinder “shut-off” valve, tighten the connection and retest (Step 5)
9. If the leak persists, do not attempt to operate appliance and contact Ukiah Co.

12
OPERATIONAL NOTES
1. DO NOT move the unit for at least 60 minutes after use to allow for cooling.
2. Allow the burner and glass crystals or lava rock to cool completely before touching.
3. Glass crystals or lava rock may be sharp. Before handling, make certain they have cooled
completely and handle them wearing protective gloves to prevent injury.
4. INLET PRESSURE: Maniford Pressure: 5 PSI. Max. gas supply: 250 PSI; Min. gas supply: 10PSI.
LIGHTING SAFETY
FOR YOUR SAFETY, READ BEFORE LIGHTING
• Make sure you are familiar with the owner’s manual and you understand all precautions noted.
• Before operating, smell around the appliance and next to the ground for gas odors because some gases are heavier
than air and may settle on the ground.
• Use only your hand to turn the gas control valve. Never use tools. If the valve will not turn (that is, without the use of a
tool), do not try to repair it. Call a qualied service technician.
• Do not use the appliance if any part has been submerged in water. Immediately call a qualied service technician to
inspect the unit and to replace any part of the control system and any gas control that has been under water.
• Make sure the igniter batteries have been installed properly. The igniter will not operate otherwise.
• Inspect hoses to make sure there are no kinks in them and check for leaks.
• After connecting the gas line and checking for leaks, the unit is ready to be lit. Upon the initial use, a small amount of
air will be in the lines. When rst lighting the burner, it will take a few seconds for the lines to purge themselves of this
air.
• Once purging is complete, the burner will light and operate as indicated in the instruction manual. Subsequent
lighting of the unit will not require purging unless the gas supply has been disconnected.
WARNING: Read and follow the safety and lighting instructions in this manual and on the labels on the appliance.
IMPROPER SETUP OR USE COULD RESULT IN A FIRE OR EXPLOSION RESULTING IN PROPERTY DAMAGE, INJURY OR
LOSS OF LIFE.

13
BEFORE USE
[Figure 1] - Install one AA battery.
[Figure 2] - Lithium-ion battery charger
input.
[Figure 3] - 20LB Propane Tank Cover.
IGNITION BATTERY
1. Install one AA battery for the electronic ignition located inside
of the unit (AA battery included). Begin by carefully ipping the
unit upside down, and unscrew igniter battery compartment cap
counterclockwise. Insert battery with positive side facing out, then
tighten igniter cap back on (make sure the battery is installed the
proper direction). [Figure 1]
CHARGING THE AUDIO BATTERY
1. Before using your Ukiah Co. audio system, fully charge the lithium-
ion battery by plugging the charging cable provided into the charging
port on the unit. [Figure 2]
• The LED INDICATOR on the charger will turn RED when the battery
is charging.
• The LED INDICATOR will turn GREEN when the battery is fully
charged.
The battery will take up to 6 hours to fully charge and will run for
up to 20 hours on a single charge. The unit can be operated while
connected to the charger. The internal battery powers the audio
system only and is not needed for “Fire Only” mode.
WARNING — Charge the battery by using only the original
charging cable supplied. Using another charging cable may harm the
battery.
LAVA ROCK/GLASS MEDIA
1. Open the box of included media and carefully place in the burner
tray, making sure not to cover the screen that protects the ignition
system or the holes of the burner.
PROPANE TANK COVER
1. Slip the propane tank cover down over the tank. Once covered,
tighten the top and bottom pull cords to secure to tank. [Figure 3]

14
[Figure 4] - Turn gas control to “OFF”.
[Figure 5] - Connect supplied regulator
and do not over-tighten.
[Figure 6] - Attach quick-connect end of
regulator to the unit.
REGULATOR CONNECTIONS:
Your Ukiah Co gas re pit is equipped with a specialized pressure
regulator, which is a device to control and maintain uniform gas
pressure as gas is released from the LP cylinder. This pressure
regulator is designed for vapor withdrawal.
WARNING: Use only the original specially designed regulator
supplied with your unit. Using another regulator may be dangerous.
WARNING: Use tanks that are marked “Propane Fuel” only.
WARNING: Read carefully all instructions contained on the
information plate attached to the re pit.
WARNING: Do not transport your re pit with LP Tank connected.
1. Place the re pit in the desired location. Make sure that it is placed
outdoors in a well-ventilated area away from any ammable structures,
awnings, vegetation, etc.
2. Place your 20lb LP tank in a location that is not in a walkway or
where it can be easily knocked over. Always use the provided tank
stand (see page 7 for details). Maintain 60 inches between the unit
and tank. For safest operation use a commonly-available LP tank
holder.
3. Make sure the unit gas control knob is turned to “OFF” by pushing
it in and turning it clockwise to the off position. [Figure 4]
4. Make sure the propane cylinder valve is turned off by turning valve
clockwise.
5. While holding carrying handle closest to propane cylinder, connect
regulator to propane cylinder and turn clockwise until snug (DO NOT
OVER-TIGHTEN). Use only supplied regulator included with your unit.
[Figure 5]
6. Attach quick-connect on opposite end of regulator hose to your
unit. [Figure 6]
WARNING: Do not over-tighten or use a wrench to tighten the
regulator connection. Over-tightening could damage the regulator
coupling and cause a leak.
LP TANK REMOVAL:
When the LP tank needs to be replaced, follow these instructions to
remove it.
1. Make sure gas control knob is turned “OFF” by pushing it in and
turning it clockwise to the off position.
2. While holding carrying handle closest to propane cylinder with one
hand, unscrew propane cylinder from regulator.
SETUP INSTRUCTIONS

15
[Figure 7] - Turn gas control to “OFF”.
[Figure 8] - Press, hold and turn to low.
WARNING: Before lighting, remove weather cover and remove lid
when applicable.
WARNING: DO NOT stand with your head or arms over the re pit
at any time.
1. Make sure gas control knob on unit is set to “OFF”, then turn on
the gas supply. Open the tank valve fully by slowly turning the handle
counterclockwise. [Figure 7] Purge the gas supply line of any trapped
air and check for leaks prior to the rst lighting of the unit. See
“Lighting Safety” section for details.
2. To ignite, push and hold gas control knob on unit for 3 - 5 seconds
while turning to “LOW” and once ignited continuing to depress the
gas control knob for an additional 5-10 seconds before releasing. The
ame should stay lit. This will actuate the thermocouple. [Figure 8]
NOTE: The built in thermocouple safety device needs to warm up to
engage, ensuring the gas will be shut off in the event of the unit being
tipped over or blown out.
3. If igniter does not light burner, replace AA battery or use a long
match or long butane lighter.
4. Adjust ame to desired level with the gas control knob on the unit.
5. After operation, turn all gas knobs to the “OFF” position and push
the ON/OFF switch to off. Remember to turn the valve on top of the
gas cylinder to the “OFF” position.
IF BURNER DOES NOT IGNITE:
If ignition is not immediate, push and turn the control knob
clockwise to “OFF”. The gas supply will automatically shut off after
approximately 10 seconds (+/- 3 seconds) if a ame does not start or
it is extinguished. If this happens, wait 5 minutes for gas fumes to clear
and re-try or refer to the troubleshooting section if the unit does not
re-start. If problem cannot be resolved, do not attempt to operate the
appliance; contact your dealer or approved service center.
LIGHTING INSTRUCTIONS

16
CHARGING THE BATTERY
Before using your Ukiah Co. audio system, follow steps on page
13 to fully charge the lithium-ion battery. [Figure 9]
PAIRING TO A Bluetooth® DEVICE
1. Turn your Bluetooth® device OFF entirely and then turn it back
ON to refresh the device’s Bluetooth® memory.
2. Find the Bluetooth® menu in your device and make sure the
Bluetooth® function is turned ON (refer to your device’s user
manual for instructions on nding the Bluetooth® menu).
3. Turn your Ukiah Co. product ON using the ON / OFF SWITCH.
The audio system will say “Power On”. [Figure 10]
4. On your device, perform a Bluetooth® “device discovery” to
add “UKIAH 2.1” as a new device.
5. When the speaker is discovered your device will display
“UKIAH” in the Bluetooth® menu.
6. When your device is connected, the audio system will say
“connected”.
• NOTE: Keep the Bluetooth® function on your device ON, to
ensure the speaker can automatically pair with your device the
next time the audio system is turned ON.
PLAYING MUSIC
After successfully pairing the unit with your Bluetooth® device,
you can begin playing music or any audio through your device’s
menu system (refer to your device user manual for instruction on
playing music).
ADJUSTING THE VOLUME
The speaker volume can be adjusted by turning the volume
control knob located on the front of the unit, or directly on your
Bluetooth® device. [Figure 11]
WARNING: Playing music at high volumes can damage
hearing.
USING THE SPEAKER FOR HANDS-FREE PHONE CALLS
Once your smart-phone has successfully paired with your Ukiah
Co. product, you can use the speaker and built-in microphone for
hands-free calls.
NOTE: The MIC is located on the front of the unit just below
the volume control knob. For best call quality remain near the
product.
[Figure 9] - Audio battery charging port.
[Figure 10] - Audio system power button.
[Figure 11] - Audio volume control knob.
AUDIO SYSTEM

17
Follow the below steps to start “Beat to Music” mode after setup
and lighting in “Fire Only” mode (page 14-15).
AFTER FIRE PIT IS LIT:
WARNING: Sudden ame height and regular intensity
changes occur when “Beat to Music” mode is engaged. Once
audio device is connected, stay clear of burner area before
playing audio clip.
1. Push the “Beat to Music” button. Button will glow orange when
ON. [Figure 12]
2. Turn gas control knob to the “Beat to Music” icon. When the two
icons are matched, “Beat to Music” mode will be engaged and
the ame will drop down to a lower height. [Figure 13]
3. After Bluetooth® connection is made (page16), stand clear
of re pit and play your audio. Observe the re reacting to the
sound.
4. Control the sensitivity of the re show by turning the volume up
or down on your phone or media device being used.
* Higher volume produces a more reactive re show.
* Lower volumes produce a less reactive re show.
Fire show may vary from song to song, genre or delity of audio
clip. “Beat to Music” works with any audio including music, audio
books, pod-casts and stories.
5. Use the volume control knob on the unit to adjust speaker
volume up or down.
POWER DOWN “BEAT TO MUSIC”:
1. Turn off the “Beat to Music” button.
2. Turn gas control knob to OFF or to “Fire Only” mode.
[Figure 12] - Beat to Music power button.
[Figure 13] - Beat to Music (BTM) gas control
knob setting.
BEAT TO MUSIC OPERATION

18
MAINTENANCE
1. The appliance should be inspected before initial use and inspected at least annually by a qualied service technician.
2. Tampering or failure to follow all directions and warnings is DANGEROUS and voids all warranties. Any component
found to be faulty or damaged must be replaced by a qualied service technician with an approved component.
3. This unit is designed for the valve to be fully opened from the fuel source. If not operating at full fuel ow, black
smoke may start to occur. Always make certain that the valve on the gas tank is in the full open position during
operation of the unit to prevent smoke.
4. Periodically remove the glass crystals and/or lava rock and examine the burner unit and its components. If the
components are dirty, clean with soft brush and soapy water solution before carefully replacing. Also examine the
area around the burner. Any dirt or foreign material, such as spider webs or nests should be removed. This will ensure
trouble-free operation.
5. Periodically check the hose that connects to the gas cylinder to ensure that it is not cracked or damaged in any way.
Perform leak tests at least annually and replace the hose when excessive wear or damage is observed.
STORAGE
STORAGE OR NON-USE:
• Store the LP gas tank outdoors in a well-ventilated place.
• Do not store the LP gas tank in direct sunlight or near a source of heat or combustion.
• If you intend to store the re pit indoors, disconnect and remove the LP gas tank rst. Disconnected tanks must have
a dust cap installed and must not be stored in a building, garage or any other enclosed area.
• Keep out of the reach of children.
• When the LP gas tank is connected to the gas re pit, the gas re pit and LP gas tank must be stored outside in a well-
ventilated place.
STORAGE INSTRUCTIONS
1. Do not move or store this gas re pit until the re has been extinguished and the appliance is cool to the touch.
2. Disconnect the gas source and install the valve plug in the 20lb LP tank.
3. Store the fully assembled unit in a ventilated location away from children and pets.
4. Turn power button off when not using the unit.

19
PROBLEM POSSIBLE CAUSE SOLUTION
Burner won’t light.
Propane cylinder is frosted over. Wait until the propane cylinder
warms up and becomes unfrosted.
Blockage in orice. Clear blockage.
Control knob is not in ON position. Turn control knob to ON.
Burner ame is low.
Gas pressure is low. Turn cylinder valve OFF and replace
cylinder.
Outdoor temperature is less than 40ºF
and tank is less than 1/4 full.
Use a full cylinder.
Control knob not fully ON or orices
blocked.
Check control knob position and
check burner and orices for block-
age.
Carbon build-up.
Thick black smoke.
Blockage in burner holes. Remove blockage from burner holes.
Regulator hose is kinked. Straighten hose of all bends or kinks.
TROUBLESHOOTING

20
WARRANTY
ONE-YEAR LIMITED WARRANTY
• The Limited Warranty described above is extended only to the original end-use purchaser and is non-transferable.
It does not include parts or labor to repair damage caused by mishandling, accident, negligence, misuse, normal
wear and tear, normal cosmetic deterioration, or damage caused by environmental conditions. While necessary
repairs or maintenance on your Ukiah Co. product can be performed by any company, we recommend that you use
only authorized Ukiah dealers and parts. Incorrectly performed or improper repair or maintenance voids this Limited
Warranty.
• There are no express warranties except as listed above.
• The purchaser assumes all risks in the assembly, operation, and maintenance of this unit.
• Failure to follow the warnings and operational instructions contained in this manual can result in personal injury and/
or property damage.
• This Limited Warranty is in lieu or all other express warranties, and is the sole and exclusive warranty provided
by Ukiah Co. Ukiah Co. disclaims all warranties for products that are purchased from sellers other than authorized
distributors or retailers, including the warranty of tness for a particular purpose or the warranty of merchantability.
• Upon expiration of this Limited Warranty, Ukiah Co. disclaims and will not be liable or responsible for any other
warranty, including express and implied warranties. This means that to the extent allowed by law, starting on the
applicable Ukiah Co. Limited Warranty expiration date, all Ukiah Co. Products are provided on an “as is” basis, and
Ukiah Co. disclaims all warranties and conditions with respect to the Ukiah Co products, whether implied, express,
or statutory, including the implied warranties of tness for a particular purpose, merchantability, non-infringement of
third-party rights, title, quiet enjoyment, availability, quality of service or results, satisfactory quality, accuracy, and any
warranties arising from any course of dealing, usage or trade practice in connection with such products.
• Ukiah Co. further disclaims any implied or express warranty of, and assumes no responsibility for, defects in
workmanship caused by third parties.
• In no event will Ukiah Co., its directors, ofcers or agents be liable to the purchaser of this device or any third party,
whether in tort, or in contract, or on any other basis, for any indirect, special, punitive, exemplary, consequential, or
incidental damage, loss, or cost arising in connection with or out of the sale, use, maintenance, or inability to use the
product, even if Ukiah Co. or its directors, ofcers, or agents have been advised of the possibility of such damages,
losses, or costs, or if such damages, losses, or costs are foreseeable. In no event will Ukiah Co. or its directors, ofcers,
or agents be liable for any direct damages, losses, or costs that exceed the purchase price of the product.
• This Limited Warranty gives the purchaser specic legal rights, and the purchaser may also have other rights which
vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sales of
Goods shall not apply to this Limited Warranty or the sale of products covered by this Limited Warranty.