Ultra Start 1172 SERIES User manual

REV.2007.11.14A
TM
1172 SERIES
Advanced Remote Starters &
Vehicle Security Systems
INSTALLATION GUIDE
TM
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this devise.
www.ultrastarters.com

SYSTEM PROGRAMMING - Menu 1
PAGE 2
INSTALL MANUAL
TABLE OF CONTENTS
QUICK VIEW WIRING DIAGRAM..........................................................3-4
Connector Pin Configuration
Antenna Connector
Park Light Jumper
QUICK VIEW PROGRAMMING..............................................................5-9
Enter Program Mode
System Reset
Transmitter Programming
Menu 1,2,3 & 4 Quick View
Auto Tach Learning
Manual Tach Learn (Vehicles without start wire)
SYSTEM WIRING DETAILS................................................................10-14
Connector Views
Wiring Description
PROGRAM MENUS............................................................................15-21
Program Menu 1 Details
Program Menu 2 Details (4-Button Button Remote Required)
Program Menu 3 Details
Program Menu 4 Details
TACH MODES..........................................................................................22
Normal Operation
Hybrid Mode 1 &2
DOOR LOCK DIAGRAMS..................................................................23-24
Relay Diagrams
TRANSMITTER PROGRAMMING...........................................................25
Adding / Reprogramming Transmitter
DIAGNOSTICS..........................................................................................26
Diagnostic Chart
Diagnostic Memory
NOTES......................................................................................................27
CONTACT INFORMATION.......................................................................28
(4-Button Button Remote Required)
1172 SERIES

(+) GLOW PLUG - PROGRAMMABLE/ - SEE PAGE 13(+) START TRIGGER
SYSTEM PROGRAMMING - Menu 1
PAGE 3
1172 SERIES
INSTALL MANUAL
QUICK VIEW WIRE DIAGRAM
1
5
3
2
4
6
1
2
3
4
5
6
7
8
9
1
2
SYSTEM GROUND INPUT
SELECTABLE PARK LIGHT OUTPUT (DEFAULT POSITIVE)
STATUS LED
PROGRAM / VALET BUTTON
BLACK
WHITE
OUTPUT TO ACTIVATE IGNITION CIRCUITTHE VEHICLES BLUE
SELECTABLE OUTPUT* (DEFAULT 2ND IGN) SEE PAGE 11 WHITE*
12VOLT/ 30 AMP MAIN POWER INPUT RED
OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT YELLOW
12VOLT/ 30 AMP MAIN POWER INPUT RED
OUTPUT TO ACTIVATE ACCESSORY CIRCUITTHE VEHICLES GREEN
(-) AUXILIARY 1 OUTPUT - PROGRAMMABLE - SEE PAGE 13
BLACK
(-) AUXILIARY 2 OUTPUT - PROGRAMMABLE - SEE PAGE 13 RED/WHITE
(-) REARM OUTPUT - PROGRAMMABLE - SEE PAGE 13 YELLOW
(-) DISARM OUTPUT (PULSE WITH UNLOCK & BEFORE START) BROWN
(+ / -) TACH DETECTION INPUT (CONNECT TO COIL, INJECTOR...) BLUE/WHITE
(-) HOOD PIN SWITCH INPUT (GROUND WHEN HOOD IS OPENED) GREEN/WHITE
(+) BRAKE SWITCH INPUT (12VOLT WHEN BRAKE IS PRESSED)
PINK
BLUE
(-) HORN OUTPUT - PROGRAMMABLE - SEE PAGE 13 WHITE/BLUE
DO NOT INSTALL THIS SYSTEM INTO A MANUAL TRANSMISSION VEHICLE!!

SYSTEM PROGRAMMING - Menu 1
PAGE 4
INSTALL MANUAL
QUICK VIEW WIRE DIAGRAM
1
2
3
1
2
3
1
2
3
4
Position 1 or Position 2
GREEN
BLUE
N/A*
RED
BLACK
WHT/VIOLET
BYPASS MODULE DATA COMMUNICATION PORT
***FOR USE WITH COMPATIBLE BYPASS MODULES ONLY***
SELECTABLE PARK LIGHT OUTPUT
OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-)
OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-)
OUTPUT FOR VOLTAGE INVERTER*
12VOLT OUTPUT FOR BYPASS MODULE
GROUND OUTPUT FOR BYPASS MODULE
(-) WHILE RUNNING OUTPUT (BYPASS TURN ON) / STARTER DISABLE
* THE CENTER PIN OF THE KEYLESS CONNECTOR IS LOW CURRENT AND IS DESIGNED
TO SUPPLY POWER TO DOOR LOCK MODULES (DO NOT CONNECT TO RELAYS)
OVERLOADING THIS OUTPUT WILL DAMAGE THE MODULE!
**THIS CONNECTOR IS USED FOR ALARM MODELS ONLY.
*** FOR USE WITH COMPATIBLE BYPASS MODULES ONLY.
BY DEFAULT THE SYSTEM COMES WITH THE PARK
LIGHT JUMPER SET FOR POSITIVE PARK LIGHT
OUTPUT. TO CHANGE THE SYSTEM TO A NEGATIVE
PARK LIGHT OUTPUT, PLACE THE JUMPER IN THE
NEGATIVE PARK LIGHT POSITION SHOWN IN THE
DIAGRAM. (Position 2)
POSITIVE
PARK LIGHT
NEGATIVE
PARK LIGHT
1172 SERIES

SYSTEM PROGRAMMING - Menu 1
PAGE 5
INSTALL MANUAL
QUICK VIEW PROGRAMMING
Press Lock Press Unlock* Press Start Press #*
MENU 1 MENU 2 MENU 3 MENU 4
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch located on the antenna 1 time.
*The Horn will chirp and the park light will turn on to confirm that the system
has entered Program Mode.
3 - Select the Program Menu by pressing the button that corresponds to the
desired Program Menu.
ENTERING PROGRAM MODE
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and RELEASE the Program Switch 1 time.
(Horn will chip to confirm program mode has been entered)
3 - Press and HOLD the Program Switch for 5 seconds or until the Horn Chirps 3
times.
4 - Turn the ignition key OFF to exit.
4 - Press and Release the Program Switch to advance through the settings.
*The horn will chirp and LEDs flash the same number of times as the selected setting.
5 - Press and hold the Program Switch to change the setting.
(The horn will honk and the park lights will flash to indicate the option selected)
6 - To exit Program Mode, turn the key off.
(Confirmed by Long Horn Chirp)
1172 SERIES
SYSTEM RESET
*4-Button Button Remote Required For Menu 2 and 4

SYSTEM PROGRAMMING - Menu 1
PAGE 7
INSTALL MANUAL
QUICK VIEW PROGRAMMING
PROGRAM MODE 1
SETTING #
LED
FLASHES
WIRE COLOR SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1N / A
2WHITE
(2 PIN CONNECTOR)
3WHITE/BLUE
(9 PIN CONNECTOR)
VALET SETTINGS SECURE VALET
15 SECONDS
STANDARD VALET
5 SECONDS
PARK LIGHT OUTPUT 30 SECONDS ON
DISARM NORMAL OPERATION
HORN TIMING 5MS PULSED OUTPUT 50MS PULSED OUTPUT 10MS PULSED OUTPUT
PROGRAM MODE 2
PROGRAM MODE 1 - see page 16 for detailed instructions
PROGRAM MODE 2 - see page 19 for detailed instructions
IGNITION AUTO-LOCKS
DISABLED
SETTING #
LED
FLASHES
WIRE COLOR SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1BLUE & GREEN
(DOOR LOCK HARNESS)
2WHITE/BLUE
(9 PIN CONNECTOR)
3BLUE & GREEN
(DOOR LOCK HARNESS)
4BLUE & GREEN
(DOOR LOCK HARNESS)
5BLACK
(9 PIN CONNECTOR)
6RED/WHITE
(9 PIN CONNECTOR)
IGNITION
AUTO-LOCK
IGNITION AUTO-LOCK /
UNLOCK
IGNITION AUTO-LOCK
ONLY
HORN SETTINGS HORN
CHIRPS DISABLED
HORN
CHIRPS ENABLED
DOOR LOCK PULSE
OPTIONS
DOUBLE UNLOCK &
SINGLE LOCK
DOUBLE LOCK & SINGLE
UNLOCK
SINGLE LOCK & SINGLE
UNLOCK
DOOR LOCK /
UNLOCK PULSES 0.25 SEC PULSES 3 SEC PULSES 0.1172 SEC PULSES
AUX OUTPUT 1 (-) ACCESSORY OUTPUT
(#) ACTIVATES CAR FINDER
2ND UNLOCK
(-) START OUTPUT
(#) ACTIVATES CAR FINDER
TRUNK RELEASE
AUX CHANNEL (#)
AUX OUTPUT 2 DOME LIGHT OUTPUT
1172 SERIES
(4-Button Button Remote Required)

SYSTEM PROGRAMMING - Menu 1
PAGE 6
INSTALL MANUAL
QUICK VIEW PROGRAMMING
2ND
IGNITION
SETTING #
LED
FLASHES
WIRE COLOR SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1WHITE
(6 PIN CONNECTOR)
2BLUE & GREEN
(DOOR LOCK CONNECTOR)
3BLUE
(9 PIN CONNECTOR)
4YELLOW
(9 PIN CONNECTOR)
5 N / A
6 N / A
SELECTABLE
RELAY
2ND
STARTER 2ND ACCESSORY
SPECIAL DOOR
LOCK OPTIONS
UNLOCK BEFORE /
LOCK AFTER START
LOCK AFTER STARTER SHUT
OFF NO ADDITIONAL PULSES
GLOW PLUG/
START TRIGGER
(-) GLOW PLUG OR 20
SECONDS DELAY
POSITIVE TRIGGER TO
START (1 PULSE) GAS/ POSITIVE GLOW PLUG
RE-ARM OPTIONS PULSE WITH LOCK PULSE AFTER START
(DEFROST / SEAT)
PULSE WITH LOCK & AFTER
SHUTDOWN
RUNTIME 4 MINUTE RUNTIME
PRESS BUTTON ONCE TO
START
45 MINUTE RUNTIME 15 MINUTE RUNTIME
REMOTE START
ACTIVATION
PRESS BUTTON TWICE
TO START
PROGRAM MODE 3
PROGRAM MODE 4
PROGRAM MODE 3 - see page 21 for detailed instructions
PROGRAM MODE 4 - see page 23 for detailed instructions
AUTO TACH / TACHLESS
SETTING #
LED
FLASHES
WIRE COLOR SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1BLUE / WHITE
(9 PIN CONNECTOR)
2 N / A
3 N / A
4 N / A
TACH OPTIONS HYBRID MODE 1
ADJUST FOR
OVER-CRANK
INCREASES TACH
SETTING BY 10%
ADJUST FOR
UNDER-CRANK
DECREASE TACH
SETTING BY 10%
TACH WAIT
SETTINGS
300ms TACH CHECK
DELAY 750ms TACH CHECK DELAY NO TACH CHECK DELAY
7 N / A LEDS FLASH WHEN
LOCKED/ ARMED
LED FLASHES
LEDS DO NOT FLASH
WHEN LOCKED/
ARMED
1172 SERIES
HYBRID MODE TWO
(4-Button Button Remote Required)

* If the vehicle does not have a starter wire a manual tach learn must be
preformed. (See Page 8)
** If Tach does not learn check for proper connection on the starter wire,
ignition wire and at the Tach connection. If the connections are good, reset
the system and try again.
-For best results connect the Tach wire to a fuel injector wire.
*** If the vehicle does not start when the remote starter is activated, the park
lights will flash a diagnostic code. (See Diagnostic Chart).
****If the vehicle still does not start, check all connections and check for a
factory installed Anti-Theft system. If the Anti-Theft prevents the vehicle from
starting the remote start will flash the park lights 7 times. The system does not
have to be Tach learned if this happens, simply start the vehicle with the key
and let it run for 5 seconds then turn off.
TACH NOTES
SYSTEM PROGRAMMING - Menu 1
PAGE 8
INSTALL MANUAL
TACH / TACHLESS LEARNING
1172 SERIES

SYSTEM PROGRAMMING - Menu 1
PAGE 9
INSTALL MANUAL
TACH / TACHLESS LEARNING
1172 SERIES
AUTO TACH/ TACHLESS LEARNING
Horn will chip to confirm that
the Tach/ Tachless has been programmed.
Start the vehicle with
the ignition key.
2 CHIRPS
**For Vehicles with 12volt START wire**
To Tach/ Tachless Learn the system simply start the vehicle with the ignition key. To
confirm that a proper Tach signal has been programmed the system will chirp the
Horn and flash the Park lights two times. If the Tach wire is not connected the park
lights will flash and the Horn will chirp 4 times to indicate Tachless Mode. If the Tach
is not learned when the start button is pressed the park lights will flash 7 times.
***The system must be Tach Learned before remote starting***
MANUAL TACH/ TACHLESS LEARNING
Start the vehicle with
the ignition key.
SYSTEM PROGRAMMING - Menu 1
**For vehicles with no 12volt START wire**
Many new GM and Chrysler vehicles do not have a 12volt start wire that the remote
start is connected to. Use the following steps to manually Tach learn the system.
Press and Hold the brake pedal, Start the vehicle with the key then place the
transmission into reverse to reduce the RPM. Press and release the program button
then press and hold it for 5 seconds. The Horn will chirp and the lights will flash
two times to confirm that a proper Tach signal has been programmed the system.
If the Tach wire is not connected the park lights will flash and the Horn will chirp 4
times to indicate Tachless Mode. If the Tach is not learned when the start button is
pressed the park lights will flash 7 times.
***The system must be Tach Learned before remote starting***
BRAKE
Hold the
brake
4 CHIRPS
Horn will chip to confirm
that the Tach/ Tachless has been
programmed.
2 CHIRPS
4 CHIRPS

SYSTEM PROGRAMMING - Menu 1
PAGE 11
INSTALL MANUAL
SYSTEM WIRING DETAILS
WHITE
SYSTEM GROUND INPUT
JUMPER SELECTABLE PARK LIGHT OUTPUT (+ OR -)
BLACK
BLUEOUTPUT TO ACTIVATE IGNITION CIRCUIT
RED30A HIGH CURRENT 12VOLT INPUT
YELLOWOUTPUT TO ACTIVATE START CIRCUIT
RED30A HIGH CURRENT 12VOLT INPUT
GREENOUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT
BLUENEGATIVE OUTPUT FOR UNLOCK
12+ OUTPUT FOR DOOR LOCK MODULE
GREENNEGATIVE OUTPUT FOR LOCK
4 PIN AUXILIARY SENSOR CONNECTOR
WHITE*SELECTABLE OUTPUT (DEFAULT SECOND IGNITION)
1172 SERIES
2-PIN CONNECTOR
6-PIN CONNECTOR

SYSTEM PROGRAMMING - Menu 1
PAGE 10
INSTALL MANUAL
SYSTEM WIRING DETAILS
1172 SERIES
PIN 1
PIN 1
YELLOW
BLACK
PIN 2
PIN 2
GREEN
WHITE
PIN 3 RED
PIN 4 RED
PIN 5 BLUE
PIN 6 WHITE
STARTER
OUTPUT
SYSTEM
GROUND
This wire will test 0V with the key off, in the Accessory position and when the
Ignition is in the on. This wire is 12volts during the start/ crank position only.
Connect to chassis ground.
HEATER
OUTPUT
PARK LIGHT
OUTPUT
(SELECTABLE)
This wire will test 0V when key is off, 12volts in the ACC and IGN positions
and off during start/ crank position
Connect to the vehicles positive Park light wire or change the jumper and
connect to the vehicle negative Park light wire. The default position of the
jumper is Positive Park Light Output.
12v INPUT 30A This input supplies the 12volt power for the Accessory and Starter outputs.
12v INPUT 30A This input supplies the 12volt power for the Accessory and Starter outputs.
IGNITION
OUTPUT
This wire will test 0V in the off and Accessory positions the switch to12volts
in the Ignition and Start positions.
SELECTABLE
OUTPUT
2nd Ignition, Accessory or Start output. Programmable.
Note: This output does not switch to default when the system is reset.
PIN 1 GREEN
PIN 2 N / A
PIN 3 BLUE
(-) LOCK
OUTPUT
Connect to lock wire from the switch on vehicles with a negative type switch. **LOW
CURRENT ONLY**
12V + DOOR
LOCK INVERTER
This output will supply 12volts for a plug-in type door lock module. Do not use this input
to power-up relays **LOW CURRENT ONLY**
(-) UNLOCK
OUTPUT
Connect to unlock wire from the switch on vehicles with a negative type switch. **LOW
CURRENT ONLY**
2-PIN CONNECTOR
4 PIN AUXILIARY SENSOR CONNECTOR

9 PIN CONNECTOR
SYSTEM PROGRAMMING - Menu 1
PAGE 12
INSTALL MANUAL
SYSTEM WIRING DETAILS
PINKBRAKE SWITCH INPUT (+) WHEN BRAKE IS PRESSED
GREEN/WHITEHOOD PIN SWITCH INPUT (-) WHEN HOOD IS OPEN
BLUE/WHITE(+ / -) TACH WIRE INPUT (CONNECT TO COIL, INJECTOR..)
BLUE NEG TRIGGER TO START / GLOW PLUG - PROGRAMMABLE
YELLOWOUTPUT FOR FACTORY ALARM RE-ARM
OUTPUT FOR FACTORY ALARM DIS-ARM BROWN
AUX OUTPUT 1 - NEG STARTER - PROGRAMMABLE BLACK
WHITE/BLUEHORN HONK NEGATIVE - PROGRAMMABLE
1172 SERIES
AUX OUTPUT 2 - NEG TRUNK - PROGRAMMABLE RED/WHITE

SYSTEM PROGRAMMING - Menu 1
PAGE 13
INSTALL MANUAL
SYSTEM WIRING DETAILS
1172 SERIES
PIN 1 YELLOW
PIN 2 BROWN
PIN 3 BLACK
PIN 4
PIN 7
RED /WHITE
GRN/WHITE
PIN 5
PIN 8
WHITE/BLUE
BLUE/WHITE
PIN 6
PIN 9
PINK
BLUE
RE-ARM (-)
PROGRAMMABLE
Supplies one .75 second pulse when locked and one .75 second pulse
after remote start shutdown. Factory alarm re-arm/ RAP shutdown.
DISARM (-)
Supplies one .75 second pulse when the unlock button is pressed and one
.75 second pulse before remote start activation. For factory alarm dis-arm/
“wake up”.
AUX #1
OUTPUT (-)
PROGRAMMABLE
Default- AUX channel output when the # button is held with no car finder
on # button. It can also be programmed to a (-) Accessory or (-) Starter
output with the (#) button activating car finder mode.
AUX #2
OUTPUT (-)
PROGRAMMABLE
HOOD PIN
INPUT (-)
Default- Output activates when the Unlock button is held for at least 3
seconds. The output will stay on for 5 seconds or until the button is
released. Programmable for Dome light Output or 2nd Unlock Output.
Connect this wire to the supplied hood pin switch. If ground is detected on
this input the remote starter will not activate.
HORN
OUTPUT (-)
PROGRAMMABLE
TACH WIRE
INPUT (A/C)
Connect this wire to the factory Horn wire of the vehicle. This connection
will provide audible confirmation when programming and when a function
is performed.
This wire is used to to detect when the vehicle has started. The Tach
source is typically taken from a fuel injector, coil, coil pack or crank
position sensor. The Tach wire is generally found as the opposite from the
common wire at the coil or fuel injector.
BRAKE
SWITCH
INPUT (+)
GLOW PLUG
INPUT (+)
This wire must be connected to the wire at the brake switch that changes
to 12volts when the brake is pressed.
Default Gas Mode or Positive Glow Plug if the Gray/Black is connected.
Programmable for Negative Glow Plug or (+) Start Trigger.

1- WHITE/VIOLET Wire- Ground When Running (-)
Connect this wire to the your bypass modules negative turn on wire. When the remote starter is
activated this wire will switch to ground.
2- BLACK Wire- System Ground (-)
Connect this wire to the ground input on the bypass module.
3- RED Wire- 12volt Power Input (+)
Connect this wire the 12volt input on the bypass module.
3 PIN BYPASS CONNECTOR
SYSTEM CHASSIS GROUND INPUT
RED
CONSTANT 12 VOLT INPUT (20AMP)
BLACK
WHITE/VIOLET
GROUND WHEN RUNNING OUTPUT
***DATA LINK CONNECTOR - FOR USE WITH COMPATIBLE BYPASS MODULES ONLY***
This connector eliminates the need to connect the lock, unlock, trunk, ignition, ground when
running and other outputs to the bypass module. These function are controlled through this
Data Link Connector.
4 PIN DATA BYPASS
TRANSMITTER PROGRAMMING
1 - Cycle the Ignition Key On/Off On/Off On. (Leaving the key ON)
2) Press and HOLD the Program Switch.
(The HORN will chirp 1 time, CONTINUE to HOLD)
**If the HORN does not chirp turn the key off, then repeat step 1**
3) Continue to HOLD the Program Switch and the HORN will chirp 5 times.
4) Press the START BUTTON on each of remote’s to be programmed.
*Pause for about 1 second between programming of each remote.
System can accept 4 remotes max.
5) The Park lights will flash once and the HORN will chirp once each time a new code is learned.
6) Release the Program switch and turn Ignition OFF.
SYSTEM PROGRAMMING - Menu 1
PAGE 14
INSTALL MANUAL
SYSTEM WIRING DETAILS
1172 SERIES

Press Lock Press Unlock Press Start Press #
MENU 1 MENU 2 MENU 3 MENU 4
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time. (The Park lights will turn on and the Horn
will chip to confirm that program mode was entered)
3 - Select the Program Menu by pressing...
ENTERING PROGRAM MODE
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and RELEASE the Program Switch 1 time.
(HORN will chip to confirm that program mode was entered)
3 - Press and HOLD the Program Switch for until the HORN Chirps 3 times.
4 - Turn ignition key OFF to exit.
Note- System reset does not delete the transmitter codes from memory or reset Menu 3 Setting
1 (selectable Output) back to second ignition. This setting must be manually changed.
SYSTEM RESET
4 - Press and Release the Program Switch to advance through the settings.
(Confirmed by HORN chirps & LED flashes)
5 - Press and hold the Program Switch to change the setting.
(Confirmed by HORN Chirps)
6 - To exit Program Mode, turn key off.
(Confirmed by Long HORN Chirp)
SELECT AND CHANGE
*4-Button Button Remote Required For Menu 2 and 4
SYSTEM PROGRAMMING - Menu 1
PAGE 15
INSTALL MANUAL
PROGRAM MODE
1172 SERIES

SYSTEM PROGRAMMING - Menu 1
SYSTEM PROGRAMMING - Menu 1
PAGE 16
INSTALL MANUAL
PROGRAMMING
1172 SERIES
SETS OPTION 1 – AUTO-LOCK & UNLOCK ENABLED- The doors will lock when
the key is turned on and unlock the when the key is turned off.
SETS OPTION 2 – AUTO LOCK ONLY ENABLED- The doors will lock when the key
is turned on but will not unlock when te key is turned off.
SETS OPTION 3 – AUTO LOCK DISABLED- The doors will not lock or unlock
when the key is turned on or off. (DEFAULT)
SETS OPTION 1 – HORN DISABLED- The HORN and HORN and will activate with
Panic and Car Finder Mode only.
1 CHIRP
1 CHIRP
2 CHIRP
3 CHIRP
CHANGE SETTING 1 -
GOTO SETTING 2 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 1- IGNITION AUTO-LOCKS
THE HORN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED 1 CHIRP
PRESS
1 TIME
2 CHIRPS SETS OPTION 2 – HORN OUTPUT- The HORN and the HORN* (alarm models)
output will activate for all functions. (DEFAULT)
SETS OPTION 1 – DOUBLE UNLOCK & SINGLE LOCK PULSE- The system will
provide 2 unlock pulses w/unlock and 1 lock pulse w/lock.
1 CHIRP
SETS OPTION 2 - DOUBLE LOCK & SINGLE UNLOCK PULSE- The system will
provide 2 lock pulses and 2 unlock pulses.
1X
CHANGE SETTING 2 -
GOTO SETTING 3 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 2-HORN OUTPUT
THE HORN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED 2 CHIRPS
PRESS
1 TIME
2X
SETTING 3-DOOR LOCK PULSES
THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED 3 CHIRPS
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
2 CHIRPS
SETS OPTION 3 – NORMAL OPERATION- The system will pulse once for lock
and once for unlock. (DEFAULT)
3 CHIRPS
CON'T ON NEXT PAGE
ENTERING PROGRAM MODE 1
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
HORN CHIRP
Press and release the
antenna 1 time or press
LOCK on4 button remote
PROGRAM SWITCH

SETS OPTION 1 - SHORT PULSES- The output for lock and unlock is .25sec. Helps
prevent windows from rolling up/down on some vehicles..
SETS OPTION 2 – LONG PULSES- The output for lock and unlock is 3 seconds.
Used to activate vacuum door lock systems.
SETS OPTION 3 – NORMAL PULSES- The output for lock and unlock is .75sec.
Used for most vehicles. (DEFAULT)
CON'T FROM PREVIOUS PAGE
CHANGE SETTING 4 -
GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 4- DOOR LOCK TIMING
THE HORN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED 4 CHIRPS
PRESS
1 TIME
4X
1 CHIRP
2 CHIRPS
3 CHIRPS
CHANGE SETTING 5 -
GOTO SETTING 6 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 5- AUX OUTPUT 1
THE HORN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED 5 CHIRPS
PRESS
1 TIME
5X
1 CHIRP
2 CHIRPS
3 CHIRPS
CHANGE SETTING 6 -
GOTO SETTING 7 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 6- AUX CHANNEL 2
THE HORN WILL CHIRP 6 TIMES WHEN SETTING 6 IS SELECTED 6 CHIRPS
PRESS
1 TIME
6X
1 CHIRP
2 CHIRPS
3 CHIRPS
SETS OPTION 1 – NEGATIVE ACCESSORY OUTPUT- Output acts as a negative
accessory output. # Activates Car Finder Mode.
SETS OPTION 2 – NEGATIVE STARTER OUTPUT- Output acts as a negative starter
output. # Activates Car Finder Mode.
SETS OPTION 3 –AUXILIARY CHANNEL OUTPUT- Press and hold the # button to
activate auxiliary with unlock and disarm pulse.(DEFAULT)
SETS OPTION 1 – DOME LIGHT OUTPUT- The turns on for 30 seconds with unlock
and turns off with lock and ignition on.
SETS OPTION 2 – 2nd UNLOCK- The output will activate when the unlock button is
pressed twice within 3 seconds.
SETS OPTION 3 – TRUNK RELEASE- OUTPUT ACTIVATES WHEN UNLOCK
BUTTON IS PRESSED AND HELD FOR 3 SECONDS (DEFAULT)
Not Available on 1172 Series
Not Available on 1172 Series
SYSTEM PROGRAMMING - Menu 1
PAGE 17
INSTALL MANUAL
PROGRAMMING
1172 SERIES

SYSTEM PROGRAMMING - Menu 1
PAGE 18
INSTALL MANUAL
PROGRAM MODE
1 CHIRP
1 CHIRP
2 CHIRPS
CHANGE SETTING 1 -
GOTO SETTING 2 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 1- VALET SETTINGS
THE HORN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED 1 CHIRP
PRESS
1 TIME
2 CHIRPS
1 CHIRP
1X
CHANGE SETTING 2 -
GOTO SETTING 3 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 2-PARK LIGHT OUTPUTS
THE HORN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED 2 CHIRPS
PRESS
1 TIME
2X
SETTING 3-HORN OUTPUT
THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED 3 CHIRPS
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
2 CHIRPS
3 CHIRPS
CON'T ON NEXT PAGE
SETS OPTION 1 – 30 SECOND- The park light output will flash for all functions and
will stay active for 30 seconds when unlock is pressed.
SETS OPTION 2 – NORMAL OPERATION- The park lights will flash for all
functions. (DEFAULT)
SETS OPTION 1 – SECURE- The LED/ Program Switch must be held for 15 seconds
to place the system into Valet Mode.
SETS OPTION 2 – STANDARD- The LED/ Program Switch must be held for 5
seconds to place the system into Valet Mode. (DEFAULT)
SETS OPTION 1 – SHORT OUTPUT- The HORN output will activate for 5ms when a
function is preformed.
SETS OPTION 2 – LONG OUTPUT- The HORN output will activate for 50ms when a
function is preformed.
SETS OPTION 3 – NORMAL OUTPUT- The HORN output will activate for 10ms
when a function is preformed. (DEFAULT)
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
HORN CHIRP
Press UNLOCK
Button to
Select Menu 2
REMOTE BUTTON
ENTERING PROGRAM MODE 2
1172 SERIES
4 Button Remote Required

SYSTEM PROGRAMMING - Menu 1
PAGE 19
INSTALL MANUAL
PROGRAM MODE
SYSTEM PROGRAMMING - Menu 1
ENTERING PROGRAM MODE 3
1172 SERIES
1 CHIRP
CHANGE SETTING 1 -
GOTO SETTING 2 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 1- SELECTABLE RELAY OUTPUT
THE HORN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED 1 CHIRP
PRESS
1 TIME
2 CHIRPS
3 CHIRPS
1X
CHANGE SETTING 2 -
GOTO SETTING 3 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 2-SPECIAL DOOR LOCK OPTIONS
THE HORN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED 2 CHIRPS
PRESS
1 TIME
2X
1 CHIRP
1 CHIRP
2 CHIRPS
3 CHIRPS
SETS OPTION 2 –SECOND ACCESSORY- The WHITE wire on the 6-pin connector
acts as a Second Accessory output.
SETS OPTION 3 –SECOND IGNITION- The WHITE wire on the 6-pin connector
acts as a Second Ignition output. (DEFAULT)
SETS OPTION 1 –TYPE 2 - The doors will unlock before remote start, lock when
remote starter starts and again when the remote start shuts down.
SETS OPTION 2 – RE-LOCK- The doors will automatically lock when the remote
starter shuts down.
SETS OPTION 3 – NORMAL OPERATION- No additional door lock or door
unlock pulses. (DEFAULT)
SETS OPTION 1 – SECOND STARTER- The WHITE wire on the 6-pin connector
acts as a Second Starter output.
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
HORN CHIRP
Press START
Button to
Select Menu 3
REMOTE BUTTON
CON'T ON NEXT PAGE

SYSTEM PROGRAMMING - Menu 1
PAGE 20
INSTALL MANUAL
PROGRAM MODE
CON'T FROM PREVIOUS PAGE
CHANGE SETTING 4 -
GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 4- RE-ARM OPTIONS
THE HORN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED 4 CHIRPS
PRESS
1 TIME
4X
1 CHIRP
2 CHIRPS
3 CHIRPS
CHANGE SETTING 5 -
GOTO SETTING 6 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 5- RUN TIME
THE HORN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED 5 CHIRPS
PRESS
1 TIME
5X
1 CHIRP
2 CHIRPS
3 CHIRPS
SETS OPTION 1 – 4 MINUTES- The system will run for approximately 4 minutes
then shut off.
SETS OPTION 2 – 45 MINUTES- The system will run for approximately 45 minutes
then shut off.
SETS OPTION 3 – 15 MINUTES- The system will run for approximately 15
minutes then shut off. (DEFAULT)
SETS OPTION 1 - TYPE 2- The rearm output pulses only when the lock button is
pressed.
SETS OPTION 2 – AFTER START- The re-arm output will pulse after the remote
start starts the vehicle (DEFROST/ HEATED SEAT)
SETS OPTION 3 – REARM- Pulsed output when the doors are locked and after
remote start shutdown. (DEFAULT)
1172 SERIES
1 CHIRP
SETTING 3- (+) GLOW PLUG/ INPUT TRIGGER TO START
THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED 3 CHIRP
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
2 CHIRP
3 CHIRP
SETS OPTION 1 – NEGATIVE GLOW PLUG/ 20 SECOND DELAY START
SETS OPTION 2 – POSITIVE TRIGGER TO START (1 PULSE)- 1 (+) pulse on the
input will activate remote starter.
SETS OPTION 3 – GAS ENGINE/ POSITIVE GLOW PLUG