ULTRA TEC LSG PFI-9D User manual

LSG Low Smoke Generator
w/ Power Fog Industrial 9D
Operator’s Manual
www.ultratecfx.com
VER. 04.11.12

Table of Contents
Introduction................................................................................ 3
Microprocessor Control ............................................................ 3
Water Base Fog Technology ...................................................... 3
Warning ...................................................................................... 3
Important Safety Instructions: ................................................... 3
Safety Precautions ..................................................................... 3
LSG PFI-9D Technical Specications .......................................... 4
LSG PFI-9D System w/ Roadcase ............................................... 4
LSG PFI 9D System on a Cart .................................................... 4
PFI Technical Drawings .............................................................. 4
Power Fogger Industrial 9D....................................................... 4
LSG w/ PFI-9D Technical Drawings............................................ 5
LSG PFI System on a Cart.......................................................... 5
LSG PFI-9D System in a Roadcase.............................................. 5
Operating Procedure ................................................................. 6
Operating Procedure w/ Air Option........................................... 6
Operation Procedure
LSG MK II High Pressure w/ 20 & 50lbs Cylinders ...................... 7
Figure A ................................................................................... 8
Operation Procedure
LSG MK II Low Pressure w/ 350lbs Dewar Tank ......................... 9
Figure B.................................................................................. 10
Options ..................................................................................... 11
Optional Show Control Remote Operations.......................... 11
Show Control Remote LED Indicator ....................................... 11
Show Control Operation......................................................... 12
Optional Timer/ Duration Remote Operations ...................... 12
Timer/ Duration Remote LED Indicator .................................... 12
DMX Operation........................................................................ 13
Maintenance............................................................................. 13
Exterior................................................................................... 13
Heat Exchanger ...................................................................... 13
Recommended Fluid ................................................................ 13
Maintenance Fluid .................................................................. 13
Warranty................................................................................... 14
Contact Information ................................................................ 14
Note: Please read entire manual before operating the Power Fogger Industrial
www.ultratecfx.com
2

www.ultratecfx.com 3
Introduction
The Power Fogger Industrial is a Microprocessor Controlled, Water Based Fog generating system.
Microprocessor Control
The Power Fog Industrial (PFI) features dual microprocessor control. From temperature regulation to taper back
ow control, all of the functions are monitored and processed by the two on-board processors.
Water Base Fog Technology
Water Base Fog technology is achieved by pumping a glycol/water mixture through a heat exchanger. This will
vaporize the uid as it passes through the processing block. The vaporization of the uid forces the hot mixture
through the output nozzle. When mixed with ambient air, it forms an opaque aerosol (fog). The fog is made up of
tiny droplets that form around small particles in the air. The suspended droplets refract the light, allowing the fog
to take on the color of the light illuminating it.
Warning
Important Safety Instructions:
1. Do not touch, place hands or expose skin within 20” (50 cm) of the discharge nozzle.
2. Do not remove the outer case.
3. Persons suffering from asthma or allergenic sensitivity may experience irritation, discomfort or allergic
symptoms when exposed to fog effects.
4. Ensure that this unit is grounded at all times. Failure to do so may result in serious injury.
5. Use Ultratec Special Effects uid ONLY.
Safety Precautions
1. Ensure that any operation of the machine is supervised by suitably trained and authorized personnel.
2. Do not modify the machine or use a machine which has been damaged in any way.
3. Allow sufcient air circulation around the machine at all times.
4. Protect the machine from direct weather effects and wet locations.
5. Only use uids manufactured by Ultratec Special Effects.
6. Do not continue to produce fog when visibility is reduced to 20” 50cm or below.
7. Avoid directing fog output continuously at people, structures or objects within close proximity of the discharge
nozzle.
8. Ensure that adequate exhausting arrangements are available in the event of an emergency.
9. Do not place hands or exposed skin within the rst 20” (50 cm) of the discharge nozzle at any time during fog
production.
10.Fog effects can trigger smoke alarms and detectors. Please take suitable precautions to prevent false alarms.
11.Ensure sufcient air exchange vs. CO2 released.

www.ultratecfx.com
4
LSG PFI-9D Technical Specications
Model: Power Fog Industrial (PFI)
Part Number: LSG PFI-9D System w/ Roadcase
CLF 4421 LSG Low Smoke Generator PFI-9D - 120 Volt - Low Pressure w/ Road case
CLF 4423 LSG Low Smoke Generator PFI-9D - 120 Volt - Low and High Pressure Combo w/ Road case
CLF 4422 LSG Low Smoke Generator PFI-9D - 220-240 Volt - Low Pressure w/ Road case
CLF 4424 LSG Low Smoke Generator PFI-9D - 220-240 Volt - Low and High Pressure Combo w/ Road case
CLF 4425 LSG Low Smoke Generator PFI-9D - 120 Volt - High Power PFI-9D System w/Road Case
CLF 4426 LSG Low Smoke Generator PFI-9D - 120 Volt - High Pressure PFI-9D System w/Road Case
CLF 4427 LSG Low Smoke Generator PFI-9D - 220-240 Volt - High Pressure PFI-9D System w/Road Case
LSG PFI 9D System on a Cart
CLF 4431 LSG Low Smoke Generator PFI-9D - 120 Volt - Low Pressure
CLF 4433 LSG Low Smoke Generator PFI-9D - 120 Volt - Low and High Pressure Combo
CLF 4432 LSG Low Smoke Generator PFI-9D - 220-240 Volt - Low Pressure
CLF 4434 LSG Low Smoke Generator PFI-9D - 220-240 Volt - Low and High Pressure Combo
CLF 4435 LSG Low Smoke Generator PFI-9D - 120 Volt - High Power 9D System w/Cart
CLF 4436 LSG Low Smoke Generator PFI-9D - 120 Volt - High Pressure PFI-9D System w/Cart
Power Rating: 120 Volt A.C. 50/60 Hz. 13 Amps.
220-240 Volt A.C. 50/60 Hz. 6.5 Amps.
Fluid: Water Base Fog Fluid (Use only Ultratec Fluid)
PFI Technical Drawings
Power Fogger Industrial 9D

www.ultratecfx.com 5
LSG PFI-9D System in a Roadcase
39.5
28.75
34.5
23.25
29.6
24
20
36
32.2
22
28.02
LSG w/ PFI-9D Technical
Drawings
LSG PFI System on a Cart

www.ultratecfx.com
6
Operating Procedure
1. The fog machine must be connected to a grounded supply of at least 15 amps free of any electrical interference.
2. Open a 4L or 20 Litre (5 Gallon) container of Ultratec Special Effects fog uid and insert the uid pickup tube into
the spout of the uid container.
3. Connect the Remote Handset into the rear panel connector located on the rear panel. (When using DMX the
Remote is not required).
4. Activate the Power switch located on the rear panel. The Power switch and Handset indicator will illuminate to
indicate the presence of power. If the Handset indicator does not illuminate, ensure the connector is properly
inserted.
5. The Handset indicator will begin to ash slowly, but will speed up
when the fog machine is ready to operate. After approximately 9
minutes, the fog machine will be fully heated and is ready for full
output; the indicator will be on solid.
6. It may be necessary to prime uid into the system to expel any
air. The Variow control on the remote handset should be set to
the full position. A dry hose can take between 45-60 seconds to
prime. This only needs to be done if the unit was left to run dry.
NOTE: In order to prime the fog machine, the Handset Indicator
must be a solid red which indicates that the fog machine is fully
heated.
7. To adjust the depth of the hose, simply loosen Nut ‘A’ and slide up or down the hose and retighten. Be careful not
to pinch off the ow of uid.
Operating Procedure w/ Air
Option
A) Mount the Regulator Bracket to a wall or other secure
location.
B) Attach the female coupler to the male coupler of the
Power Fog Industrial w/ Air Option or Power Fog Industrial
9D w/ Air Option.
C) Attach the air hose to the male coupler of the mounted
regulator.
D) Adjust for the desired air pressure (typically 25-50 psi).
A
C
DB
A
AA

www.ultratecfx.com 7
Operation Procedure
LSG MK II High Pressure w/ 20 & 50lbs Cylinders
The Operation Procedures outlined in this section, refer to Figure A Page 9.
1. Place the fog machine’s output nozzle rmly against the center of the foam ring, sealing it to the input port of the
LSG MK II.
Tech Tip: Proper alignment can be observed by shining a ashlight into the 10” exit port of the LSG MK II and noting
the fogger’s output nozzle is centered on the LSG MK II input port.
2. Connect the grey Twist Lock connector from the LSG MK II into the controlling power source (i.e. control port on
the rear panel of the Power Fog Family of Ultratec Special Effects Foggers). This port can be controlled via DMX, the
Timer/ Duration Remote or the Show Control Remote.
Note: Starting the ow of CO2 before the fog allows the liquid CO2 to purge the gas CO2 from the lines. The Liquid
CO2 is required for correct operation. The rule of thumb formula for calculating the purge time is 1 second for every 3
feet of hose. As the unused liquid sits in the hose, it absorbs heat and converts to its gaseous state.
3. Use Molecular Fog Fluid and adjust the ow rate to the desired fog output level. Excessive fog ow will not cool
sufciently allowing the fog to rise off of the oor.
Warning: Always secure all cylinders to prevent tipping hazards.
4. An LSG MK II High Pressure requires high pressure CO2 cylinders. These are normally available in 20 & 50lb sizes. It
is recommended that cylinders equipped with liquid siphon tubes be used.
5. The CO2 supply hose is connected to the CO2 cylinder. Exercise safe handling and connection of the tank as
indicated by the gas supplier. A sealing washer is necessary to prevent leaks between the hose and valve and is
available from your gas supplier.
6. Tighten the CO2 hose-tting snug with the appropriate wrench.
Warning: Wear eye protection and gloves to protect against cold and pressure hazards
7. Open valve slowly counter-clockwise until ow can be heard. Verify the lines have no leaks before opening the valve
fully.
8. When the fog machine is up to operating temperature, activate the control to start the CO2 for the desired purge
and pre-chill time. Purging of the CO2 gas can be noted by the change in the sound of ow. It is often desirable to
pre-chill the chamber and long runs of ductwork like a Fog Curtain. Now add fog to create the thick, white rolling
blanket that hugs the oor. On the Power Fog Family of Ultratec Special Effects Foggers, the CO2 is triggered by
DMX (DMX channel + 1) or by one of the remotes. To control using the remote, the DMX address is selected as 555.
This allows the Duration knob (turned up over 1/2 way) of the Timer/ Duration Remote or the second channel of the
Show Control Remote to trigger the LSG MK II.

www.ultratecfx.com
8
9. Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the
temperature.
10.After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect
hoses. Note that the valves and lines may be extremely cold during operation. Prevent handling and exing of lines
when chilled.
Figure A
Liquid Carbon Dioxide
LSG Control Signal
Installation Model Shown Above
Touring Model Available
High Pressure Bottles w/
Liquid Siphon Tube
Liquid Carbon
Dioxide
Liquid Siphon
Tube
Fog Fluid

www.ultratecfx.com 9
Liquid Carbon
Dioxide
Liquid Siphon
Tube
Operation Procedure
LSG MK II Low Pressure w/ 350lbs Dewar Tank
The Operation Procedures outlined in this section, refer to Figure B on Page 11.
1. Place the fog machine’s output nozzle rmly against the center of the foam ring sealing it to the input port of the
LSG MK II.
Tech Tip: Proper alignment can be observed by shining a ashlight into the 10” exit port of the LSG MK II and noting
the fogger’s output nozzle is centered on the LSG MK II input port.
2. Connect the grey Twist lock connector from the LSG MK II into the controlling power source (i.e. control port on
the rear panel of the Power Fog Family of Ultratec Special Effects Foggers). This port can be controlled via DMX, the
Timer/ Duration Remote or the Show Control Remote.
Note: Starting the ow of CO2 before the fog allows the liquid CO2 to purge the gas CO2 from the lines. The Liquid
CO2 is required for correct operation. The rule of thumb formula for calculating the purge time is 1 second for every
three feet of hose. As the liquid sits in the hose unused it absorbs heat and converts to its gas state.
3. Use Molecular Fog Fluid and adjust the ow rate to desired fog output level. Excessive fog ow will not cool
sufciently allowing the fog to rise off of the oor.
4. An LSG MK II Low requires low pressure Liquid CO2 tanks. These are normally available in a 350lb size. These are
large vacuum tanks which keep the Liquid CO2 cold. Some CO2 is consumed during storage to maintain the liquid
at -50C. These tanks provide the best performance and price characteristics of the LSG systems. Check with your
local gas supplier for availability as not every location may carry these tanks.
Warning: Wear eye protection and gloves to protect against cold and pressure hazards.
5. You must connect the supply hose to the liquid output of the liquid CO2 tank. This is usually clearly indicated on
the Liquid CO2 Tank outputs. A sealing washer is necessary to prevent leaks and is available from your gas supplier.
6. Tighten the CO2 supply-tting tight with the appropriate wrench.
7. The tank pressure is indicated on the pressure gauge and must read between 275 - 340 PSI to operate the LSG
MK II. This is achieved by opening the Pressure Builder Valve (by turning it counter clockwise) at least 1-3 hours in
advance.
8. Open the valve slowly counter-clockwise until ow can be heard. Verify the lines have no leaks before opening the
valve fully.
9. When the fog machine is up to operating temperature, activate the control to start the CO2 for the desired purge
and pre-chill time. Purging of the CO2 gas can be noted by the change in the ow sound. It is often desirable to
pre-chill the chamber and long runs of ductwork (i.e. Fog Curtain). Now add fog to create the thick, white rolling
blanket that hugs the oor. On the Power Fog Family of Ultratec Special Effects Foggers, the CO2 is triggered by
DMX (DMX channel + 1) or by one of the remotes. To control using the remote, the DMX address is selected as 555.
This allows the Duration knob (turned up over 1/2 way) of the Timer/ Duration Remote or the second channel of the
Show Control Remote to trigger the LSG MK II.

www.ultratecfx.com
10
10.Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the
temperature.
11.After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect
the hoses. Note that the valves and lines may be extremely cold during operation. Prevent handling and exing of
lines when chilled.
Figure B
Installation Model Shown Above
Touring Model Available
20 Litre Fluid
in a pail
Liquid Carbon Dioxide
LSG Control Signal
Fog Fluid
350lb Liquid Carbon
Dioxide Dewar