ULTRA TEC G3000 User manual

G3000 Fog Effects Generator
Operator’s Manual
www.ultratecfx.com
012022

Table of Contents
Note: Please read entire manual before operating the G3000 Fog Effects Generator
www.ultratecfx.com
2
Introduction ................................................................................ 3
Microprocessor Control ............................................................ 3
Water Base Fog Technology ...................................................... 3
Warning ...................................................................................... 3
Important Safety Instructions: ................................................... 3
Safety Precautions ..................................................................... 3
Technical Specifications ............................................................. 4
Technical Drawings ................................................................... 4
Operating Procedure ................................................................. 5
Digital Remote Control .............................................................. 5
G3000 Screen Shots ................................................................. 7
DMX Operation .......................................................................... 9
Other Features ........................................................................... 9
Remote Extension ..................................................................... 9
Fluid Level Detection ................................................................. 9
Maintenance ............................................................................... 9
Exterior ..................................................................................... 9
Heat exchanger ........................................................................ 9
Recommended Fluids ............................................................... 10
Maintenance Fluid .................................................................. 10
Warranty ................................................................................... 11
Contact Information ................................................................ 11

www.ultratecfx.com 3
Introduction
The G3000 Fog Effects Generator is a Microprocessor Controlled, Water Based Fog generating system.
Microprocessor Control
The G3000 features dual microprocessor control. From temperature regulation to taper back flow control, all of
the functions are monitored and processed by the two on-board processors.
Water Base Fog Technology
Water Base Fog technology is achieved by pumping a glycol/water mixture through a heat exchanger. This will
vaporize the fluid as it passes through the processing block. The vaporization of the fluid forces the hot mixture
through the output nozzle. When mixed with ambient air, it forms an opaque aerosol (fog). The fog is made up of
tiny droplets that form around small particles in the air. The suspended droplets refract the light, allowing the fog
to take on the color of the light illuminating it.
Warning
Important Safety Instructions:
1. Do not touch, place hands or expose skin within 20” (50 cm) of the discharge nozzle.
2. Do not remove the outer case.
3. Persons suffering from asthma or allergenic sensitivity may experience irritation, discomfort or allergic
symptoms when exposed to fog effects.
4. Ensure that this unit is grounded at all times. Failure to do so may result in serious injury.
5. Use Ultratec Special Effects fluid
ONLY.
Safety Precautions
1. Ensure that any operation of the machine is supervised by suitably trained and authorized personnel.
2. Do not modify the machine or use a machine which has been damaged in any way.
3. Allow sufficient air circulation around the machine at all times.
4. Protect the machine from direct weather effects and wet locations.
5. Only use fluids manufactured by Ultratec Special Effects.
6. Do not continue to produce fog when visibility is reduced to 20” 50cm or below.
7. Avoid directing fog output continuously at people, structures or objects within close proximity of the discharge
nozzle.
8. Ensure that adequate exhausting arrangements are available in the event of an emergency.
9. Do not place hands or exposed skin within the first 20” (50 cm) of the discharge nozzle at any time during fog
production.
10. Fog effects can trigger smoke alarms and detectors. Please take suitable precautions to prevent false alarms.

www.ultratecfx.com
4
Technical Specifications
Model: G3000 Fog Effects Generator
Part Number: CLF 3000 - G3000 Fog Machine / 120 Volt
CLF-3001 - G3000 Fog Machine / 120 Volt - w/ Air Option
CLF-3002 - G3000 Fog Machine / 120 Volt - w/ Industrial Option
CLF-3003 - G3000 Fog Machine / 220-240 Volt
CLF-3004 - G3000 Fog Machine / 220-240 Volt - w/ Industrial Option
CLF-3006 - G3000 Fog Machine / 220-240 Volt - w/ Air Option
CLF-3007 - G3000 Fog Machine / 120 Volt - w/ Show Control
CLF 3008 - G3000 Fog Machine / 105 Volt
Length: 25.38in 59.37cm
Width: 10.5in 26.67cm
Height: 10.63in 66.98cm
Net Weight: 41lbs 18.5kg
Power Rating: 120 Volt A.C. 50/60 Hz. 17 Amps.
240 Volt A.C. 50/60 Hz. 9 Amps.
Fluid: Water Base Fog Fluid (Use only Ultratec Fluid)
Features: 2000w Dual Core Heating Block
Technical Drawings

www.ultratecfx.com 5
Operating Procedure
1. The fog machine must be connected to a sine wave voltage supply of 20 Amps free of electrical interference.
2. Open a 4 Litre (1 Gallon) container of Ultratec Special Effects fog fluid and insert the fluid pickup tube into the spout
of the fluid container.
3. Turn ON the Power switch located on the rear panel. The Power switch will illuminate to indicate the presence of
power.
4. After approximately 9 minutes, the fog machine will be fully heated and ready for full output.
5. Set the demand from 1 to 100% using the built-in remote control or through a DMX control network.
Digital Remote Control
Valid DMX
Light
DMX In DMX Out LSG Receptacle
(2 amps)
On/Off Switch
Fog On/Off Value Down (-) Value Up (+)
Cycle
Menus
Toggle LCD
Brightness
Diagnostics Screen Button
Press “Menu” to exit
(For Service Technician)
Write to Memory
When variables are changed on
the digital remote they are written
to memory after 60 seconds or
when you change screens. The
secondary displays return to the
main menu if inactive for 60
seconds.

www.ultratecfx.com
6
REM D100 A100
Fog 0:00 FHR
D=DEMAND; This value represents the user’s
requested fog output level from 1-100%
A=ACTUAL; This value represents the current level of
fog output in relation to DEMAND due to cooler block
temperatures.
F = LOW FLUID DETECTION; F will display when
sensor detects low fluid. Machine will continue to
run or can be set to shut off when sensor activates.
H = HEATING; H will display when the blocks
are heating up. H will disappear when block
is heated to desired temp.
R = RELAY; R appears when the G3000
is powering the LSG receptical.
CYCLE ON TIME
0:00 (mm:ss)
CYCLE OFF TIME
0:00 (mm:ss)
LSG PRE-FOG TIME
0:00 (mm:ss)
DMX Address: 511
Data 0 D+1 0
Set the desired time for the fog machine to
run, using the “+” or “-” buttons.
(0-10 Minutes)
Set the desired time for the fog machine to
stop, using the “+” or “-” buttons.
(0-30 Minutes)
When connected to an LSG, set the desired
time for the LSG to purge the CO2 line before
the G3000 begins to produce fog.
(0-2 Minutes)
Using the “+” or “-” buttons select the
desired valid DMX address. (0-511)
Data = fog rate controlled 0-100%,
DMX+1=LSG power on above 50%.
DMX
511
DMX Address
TEMPERATURE BAR
Displays the block
temperature.
0-255 0-255
128 - Relay
REM = Fog machine is controlled
currently by the remote
Fog = Machine is generating
fog. WIll read “Fog Off” when
currently not generating fog.
DMX=Fog machine is
controlled through DMX.
Remote bypassed.
Displays the Cycle On Time, Cycle
Off Time, and LSG Pre-Fog Time

www.ultratecfx.com 7
G3000 Screen Shots
Machine turned on warming up with no DMX input. Note
temperature bar graph shows low, Heater “H” is on and fog is
turned off DMX is unplugged and DMX LED (bottom left) is not
on.
Note error from trying to turn on machine that is not yet hot
enough.
Machine on with remote. Not fully heated (see temp bar and H is
on) so requesting 100% but getting 27%.
Machine on with DMX. Machine was fully heated (note bar graph)
but heater starts for 100% Actual flow.
Machine warming up with DMX attached. Note “DMX” on screen
with dmx address show below set at channel 1. Note valid DMX
red LED now on (lower left).

www.ultratecfx.com
8
Menu screens for timer on/off function with remote control only. DMX control ignores these setting.
If set the Fog output stops when fluid gets low (F indicator on
main screen).
If set the Fog output stops when fluid gets low (F indicator on
main screen).
Power up starting (use not recommended)
Code versions for remote, output control, DMX.
HIDDEN MENUS
DMX address selection screen. This shows DMX set to channel 1.
Channel 1 data is 58 (0-255) channel 2 is 11.

www.ultratecfx.com 9
DMX Operation
The G3000 is equipped with DMX control as a standard feature.
1. Attach a DMX signal to the DMX IN 5 pin connector on the rear of the unit. For good DMX practice, a terminator is
used on the DMX OUT connector.
2. Select a valid DMX address on the digital remote. Data = fog rate controlled 0-100%, DMX+1=LSG power turns on
above 50%.
3. Valid DMX LED is on solid if good DMX signal is present. DMX control overrides the digital remote. Slow or irregular
flashing indicates a poor DMX signal.
Other Features
Remote Extension
The digital remote control can be undocked from the machine and
extended by a 25’ cord not supplied. This can be extended to 200’.
With the power off, press the tab located at the remote port left of the
remote control. While pressing, pull the remote out of the dock and attach
the cord.
Fluid Level Detection
The G3000 is manufactured with an Electronic Fluid Level Detection to warn
the user when the fluid has reached a low level. This information is fed to the
digital remote control where it displays “F” when the fluid level becomes low.
The machine will still run when the sensor detects low fluid. The machine can be
set to shut down on the “Low Fluid Stop” screen so it will not run dry.
Maintenance
Exterior
The casing of the G3000 is stainless steel with a powder paint coating. To clean simply wash with mild soap and warm
water.
Heat exchanger
Using high quality Ultratec fluid should result in a long heat exchanger life. (See warranty policy later in this manual).
Note: Cleaning/Rapid Change procedure can be found in the G3000 Service Manual located at:
www.ultratecfx.com
Press Tab

www.ultratecfx.com
10
EZ Kleen Preventative Maintenance Fluid: Using EZ Kleen preventative maintenance fluid on a regular basis
ensures longer life for the heat exchanger in Ultratec fog machines by reducing blockage.
All our Fog Fluids are water based. Damage will occur if Haze Fluid is used in the G3000.
Recommended Fluid
Director’s Choice Fog Fluid: The choice of professionals. Director’s Choice creates a cloud of fog with
a medium hang time while remaining clean, white, dry, and odorless.
Pro Beam Long Lasting Fog Fluid: With a hang time 2-3x greater than the Director’s Choice Fog Fluid,
the Pro Beam solution produces a slightly less white fog while remaining clean, dry, and odorless.
Quick Dissipating Fog Fluid: This fast dissipating fluid is great for applications or effects that require
quick dissipation of fog. It produces excellent steam effects that re semble nitrogen bursts and it also
keeps low-lying fog from rising too quickly when it is used with theEclipse Low Fog Generator or LSX.
Extra Quick Dissipating Fog Fluid: Dissipates 2x the rate of Quick Dissipating Fog Fluid while
maintaing similar characteristics.
Molecular Fog Fluid: A faster dissipation versus the Director’s Choice Fog Fluid. This thick, clean, white
fog is an optimal solution for a dense low-lying fog effect when chilled with the Eclipse Low Fog
Generator or LSX machines.
Party Fog Fluid: Quality fog fluid on a budget. An excellent solution for Djs, Nightclubs, Haunted Houses
etc., looking to enhance light beams and creating various smoke effects.
Maxi Fog Fluid: The perfect balance between price and performance. Maxi Fog is the ideal solution for
those who require high volume without compromise.
Maintenance Fluid