UltraLux SPX22080 User manual

1
www.ultralux.bg
USER MANUAL
RGBW LED FLOODLIGHT WITH DMX
CONTROLLING
SPX22080
Please, read carefully before operating the floodlight!

2
www.ultralux.bg
PRODUCT INFORMATION
RGBW FLOODLIGHT SPX22080 has three operating modes: AUTO, DMX and MASTER/SLAVE. The DMX
mode has 5 channels: channel 3, channel 4, channel 6, channel 8 и channel 11. The floodlight has 21 built-in
programs and an editing option in the AUTO mode. Several floodlights in DMX mode can be connected and those
in SLAVE mode will follow the program of the floodlight in AUTO mode. Using stage smoke would increase the
effect of the floodlight’s lighting.
WARNING:
1. Do not expose the luminaire directly to running water or rain for the sake of preventing the risk of
electrical shock or fire!
2. Do not look directly at the working floodlight, because it could damage your eyes!
TECHNICAL INFORMATION
Basic parameters
•Beam angle: 10⁰
•Light source: 4 in 1 LED RGBW
•Protection rate: IP65
•TFT display
•Casing: Aluminum alloy
•Breathing valve for preventing moisture penetration
•Working temperature: -30 ⁰C ÷ +40 ⁰C
•Size: 219/113/225 mm
•Weight: 3.4 kg
•Warranty: 2 years
Electro-technical information
•Voltage: 100-240 V AC
•Frequency: 50/60 Hz
•Power consumption: 80 W
•Built-in driver
Control information
•DMX channels: 3, 4, 6, 8 and 11
•Modes: DMX512/MASTER SLAVE/AUTO RUN
•Built-in effects: color shifting, color chasing, strobing, and fading
•512 separate IP addresses in DMX mode
•Regulating the color temperature

3
www.ultralux.bg
PROGRAM MENU
DISPLAY
1. DMX means, that the floodlight is in DMX mode; respectively SLAVE means, that the floodlight is in
SLAVE mode;
2. The color of the dot represents the condition of signal transmission. Green indicates that the signal is
good, while red means that the signal is interrupted;
3. Shows the floodlight’s working temperature. If the temperature reaches its maximum level the
inscription would turn yellow;
4. Shows the current menu and operational mode;
5. Indicates if the KEY LOCK function is enabled (KEY LOCK ON) or disabled (KEY LOCK OFF).

4
www.ultralux.bg
DMX
In this menu, you can connect several floodlights with a DMX cable and control them with a single DMX
console / controller.
1. Press the ENTER button, after that UP or DOWN until DMX is displayed;
2. Press ENTER again. You can select either CHANNEL or ADDRESS with pressing ENTER again.
2.1. In CHANNEL mode, [xx] represents the number of the DMX channel, that can be changed by
pressing the UP or DOWN buttons;
2.2. In ADDRESS mode, [xxx] represents the number of the ID address, that can be changed by pressing
the UP or DOWN buttons.
RUN MODE
In this menu, you determine how the floodlight will operate –you can select DMХ mode or SLAVE mode.
In SLAVE mode, you can select one of the floodlights as a leading (MASTER), and the rest in SLAVE mode to
operate in accordance to its program.
1. Press the ENTER button, after that UP or DOWN until RUN MODE is displayed;
2. Press ENTER to select between the DMX or SLAVE modes and then press ENTER again to save the
selected mode.
SET UP
In this menu, you can adjust the values of the selected functions.
1 Press the ENTER button, after that UP or DOWN until SET UP is displayed;
2. Press ENTER to select one of the 9 available functions and then press ENTER again to adjust the values
of the selected function.
2.1. ID number from 1 to 66;
2.2. LED DISPLAY –by selecting ON the display would stay permanently operating; selecting OFF would
cause the floodlight’s display to stop working in 10 seconds;
2.3. KEY LOCK –selecting this function would block the floodlight’s buttons. To activate them again you
must consequently press DOWN + UP + DOWN + UP;
2.4. MAX TEMP –allows you to select maximum working temperature for the floodlight. If the
temperature is exceeded, the inscription TEMP [xx] would turn yellow;
2.5. DIMMER RED –allows you to regulate the brightness of the red color;
2.6. DIMMER GREEN –allows you to regulate the brightness of the green color;
2.7. DIMMER BLUE –allows you to regulate the brightness of the blue color;
2.8. DIMMER WHITE –allows you to regulate the brightness of the white color;
2.9. DIMMER ALL –allows you to regulate the brightness of the colors altogether.
INFORMATION
In this menu, you would find out information about the software, hardware, and the operated time of
the floodlight.
1 Press the ENTER button, after that UP or DOWN until INFORMATION is displayed;
2. Press ENTER and choose between SOFTWARE, HARDWARE, or FIX TIMES and then press ENTER again.
2.1. SOFTWARE –provides information for the software;
2.2. HARDWARE –provides information for the hardware;
2.3. FIX TIMES –shows you how many hours (in total) the floodlight has worked for.
AUTO
In this menu, you can select the AUTO mode and adjust the operating speed of the floodlight.
1. Press the ENTER button, after that UP or DOWN until AUTO is displayed;
2. Press ENTER and choose between SPEED and PROGRAM MODE and then press ENTER again.
2.1. SPEED –adjusts the speed of program changing;
2.2. AUTO MODE –provides a choice between 28 auto modes.

5
www.ultralux.bg
CUSTOMER
In this menu, you can program the floodlight to a personally adjusted mode.
1. Press the ENTER button, after that UP or DOWN until CUSTOMER is displayed;
2. Press ENTER again to choose one of the 11 pre-programmed modes that can be adjusted from the
EDIT menu.
CAL WHITE
In this menu, you can adjust the value of one of the 11 types of white color that this floodlight has.
1. Press the ENTER button, after that UP or DOWN until CAL WHITE is displayed;
2. Press ENTER again to choose one of the 11 types of white color that can be adjusted manually by
changing the values of RED, GREEN, BLUE and WHITE colors.
STAT COLOR
In this menu, you could adjust the values of the static colors and the speed of strobing.
1. Press the ENTER button, after that UP or DOWN until STAT COLOR is displayed;
2. Press ENTER again and choose one of the 5 static colors that can be manually adjusted by pressing the
buttons UP and DOWN.
2.1. STATE RED –allows you to adjust the brightness of the red color;
2.2. STAT GREEN –allows you to adjust the brightness of the green color;
2.3. STAT BLUE –allows you to adjust the brightness of the blue color;
2.4. STAT WHITE –allows you to adjust the brightness of the white color;
2.5. SELCET COLOR –allows you to choose one of the 52 available colors;
2.6. SELECT STROB - allows you to choose the strobing speed.
EDIT
In this menu, you can edit your choice of an AUTO program.
1. Press the ENTER button, after that UP or DOWN until EDIT is displayed;
2. Press ENTER again to modify one of the 11 possible programs (from PR.01 to PR.11). Each one has 32
variants that can be manually adjusted.
3. Each variant (SCENE) has an option for changing the values of the red, green, blue, and white colors
(0-255), as well as the effects FADE (0-31), FLASH (0-50), STROBE (0-31) and TIME (0-100). The settings can be
saved with holding the button ENTER for about 5 seconds.
UPLOAD
In this menu, you can connect several floodlights with DMX cables and set a leading one (MASTER) that
the rest of the floodlights (SLAVE) will follow.
1. Press the ENTER button, after that UP or DOWN until UPLOAD is displayed;
2. Press ENTER again to upload the desired program from the MASTER floodlight to the SLAVE
floodlights.
RESET
In this menu, you can recover the default settings of the floodlight.
1. Press the ENTER button, after that UP or DOWN until RESET is displayed;
2. Press ENTER again to recover the default settings.

6
www.ultralux.bg
DMX MODE
DMX channel 3
Channel
Value
Function
1
0-255
Hue
2
0-255
Saturation
3
0-255
Value(brightness)
DMX channel 4
Channel
Value
Function
1
0-255
Adjust red LEDs Dimmer from low to high
2
0-255
Adjust green LEDs Dimmer from low to high
3
0-255
Adjust blue LEDs Dimmer from low to high
4
0-255
Adjust white LEDs Dimmer from low to high
DMX channel 6
Channel
Value
Function
1
0-255
0 = Off 1 - 255 = Master dimmer
2
0-255
Adjust red LEDs Dimmer from low to high
3
0-255
Adjust green LEDs Dimmer from low to high
4
0-255
Adjust blue LEDs Dimmer from low to high
5
0-255
Adjust white LEDs Dimmer from low to high
6
0-49
default dimmer
50-99
Dimmer mode 1
100-149
Dimmer mode 2
150-199
Dimmer mode 3
200-255
Dimmer mode 4
DMX channel 8
Channel
Value
Function
1
0-255
0 = Off 1 - 255 = Master dimmer
2
0-255
Adjust red LEDs Dimmer from low to high
3
0-255
Adjust green LEDs Dimmer from low to high
4
0-255
Adjust blue LEDs Dimmer from low to high
5
0-255
Adjust white LEDs Dimmer from low to high
6
0 - 19
none
20 - 23
red
24 - 27
green
28 - 31
blue
32 - 35
yellow
36 - 39
cyan
40 - 43
magenta
44 - 47
white
48 - 51
orange
52 - 55
pink
56 - 59
violet
60 - 63
aquamarine
64 - 67
sky blue
68 - 71
full white
72 - 75
cool white
76 - 79
warm white
80 - 83
white 3200
84 - 87
white 2500

7
www.ultralux.bg
6
88 - 91
yellow 2
92 - 95
straw
96 - 99
orange 2
100 - 103
light rose
104 - 107
dark pink
108 - 111
magenta 2
112 - 115
blue 2
116 - 119
med blue green
120 - 123
dark blue
124 - 127
bright pink
128 - 131
medium blue
132 - 135
golden amber
136 - 139
deep golden amber
140 - 143
pale lavender
144 - 147
apricot
148 - 151
dark lavender
152 - 155
chocolate
156 - 159
just blue
160 - 163
surprise pink
164 - 167
scarlet
168 - 171
surprise peach
172 - 175
fire
176 - 179
english rose
180 - 183
mauve
184 - 187
bright blue
188 - 191
alice blue
192 - 195
rose indigo
196 - 199
urban blue
200 - 203
cool blue
204 - 207
Light salmon
208 - 211
mayan sun
212 - 215
cherry rose
216 - 219
flesh pink
220 - 223
skelton exotic sangria
224 - 255
amber
7
0-255
0~6 = Off 7 - 255 = Different colour auto 36
8
0-255
strobe（0Hz - 20Hz）
0~8 no function
9~255 strobe from slow to fast
DMX channel 11
Channel
Value
Function
1
0-255
0 = Off 1 - 255 = Master dimmer
2
0-255
Red LED adjustment, from low to high
3
0-255
Green LED adjustment, from low to high
4
0-255
Blue LED adjustment, from low to high
5
0-255
White LED adjustment, from low to high
6
0 - 10
No function
11 - 20
R100%/Gup/B0%/W0%
21 - 30
Rdown/G100%/B0%/W0%
31 - 40
R0%/G100%/Bup/W0%
41 - 50
Rup/Gdown/B100%W0%
51 - 60
Rup/G0%/B100%/W0%
61 - 70
R100%G0%Bdown/W0%

8
www.ultralux.bg
6
71 - 80
R100%/G0%/B0%/Wup
81 - 90
R100%/G0%/B0%Wdown
91 - 100
R↑/G↓/B0%/W0%→R↓G↑/B0%/W0%
101 - 110
R↑/G0%/B↓/W0%→R↓/G0%B↑/W0%
111 - 120
R0%/G↑/B↓/W0%→R0%/G↓/B↑/W0%
121 - 130
R↑/G↑/B↓/W0%→R↓/G↓/B↑/W0%
131 - 140
R↑/G↓/B↓/W0%→R↓/G↑/B↑/W0%
141 - 150
R↑/G↓/B↑/W0%→R↓/G↑/B↓/W0%
151 - 160
R↑/G0%/B↓/W0%→R↓/G↑/B0%/W0%→R0%/G↓/B↑/W0%
161 - 170
R↑/G100%/B↓/W0%→R100%/G↓/B↑/W0%→R↓/G↑/B100%/W0%
R↓/G↑/B0%/W0%→R0%/G↓/B↑/W0%→R0%G0%/B↓/W↑
171 - 180
R↑/G0%/B0%/W↓ R0%/G100%/B↓/W0%→R↑/G100%B0%/W0%
181 - 190
R100%/G↓/B0%/W0%→R100%/G0%/B↑/W0%→
R↓/G0%/B100%/W0%→R0%/G↑/B100%/W0%
191 - 200
RGBW
201 - 205
White 1
206 - 210
White 2
211 - 215
White 3
216 - 220
White 4
221 - 225
White 5
226 - 230
White 6
231 - 235
White 7
236 - 240
White 8
241 - 245
White 9
246 - 250
White 10
251 - 255
White 11
7
0 - 255
Speed when channel 6 is enabled
0 - 15
Default
16-255
Flicker 0Hz - 20Hz）
8
0
Default
8 - 10
Program 1
11 - 20
Program 2
21 - 30
Program 3
31 - 40
Program 4
41 - 50
Program 5
51 - 60
Program 6
61 - 70
Program 7
71 - 80
Program 8
81 - 90
Program 9
91 - 100
Custom 1
101 - 110
Custom 2
111 - 120
Custom 3
121 - 130
Custom 4
131 - 140
Custom 5
141 - 150
Custom 6
151 - 160
Custom 7
161 - 170
Custom 8
171 - 180
Custom 9
181 - 190
Custom 10
200 - 255
Custom 11
9
0 - 255
Auto mode speed
10
0 - 49
OFF dimming speed
50 - 99
Dimming speed 1
100 - 149
Dimming speed 2
150 - 199
Dimming speed 3
200 - 255
Dimming speed 4
11
0-255
ID address set

9
www.ultralux.bg
channel 11 (ID address set)
0--9
ID address
170--179
Id17
223
Id34
240
Id51
10--19
Id1
180--189
Id18
224
Id35
241
Id52
20--29
Id2
190--199
Id19
225
Id36
242
Id53
30--39
Id3
200--209
Id20
226
Id37
243
Id54
40--49
Id4
210
Id21
227
Id38
244
Id55
50--59
Id5
211
Id22
228
Id39
245
Id56
60--69
Id6
212
Id23
229
Id40
246
Id57
70--79
Id7
213
Id24
230
Id41
247
Id58
80--89
Id8
214
Id25
231
Id42
248
Id59
90--99
Id9
215
Id26
232
Id43
249
Id60
100--109
Id10
216
Id27
233
Id44
250
Id61
110--119
Id11
217
Id28
234
Id45
251
Id62
120--129
Id12
218
Id29
235
Id46
252
Id63
130--139
Id13
219
Id30
236
Id47
253
Id64
140--149
Id14
220
Id31
237
Id48
254
Id65
150--159
Id15
221
Id32
238
Id49
255
Id66
160--169
Id16
222
Id33
239
Id50
ACTIVATING AN ID ADDRESS IN DMX-512 MODE
Activate (ON) the ID function from the settings panel. Each floodlight in DMX mode could use 66
separate ID addresses.
The scheme above shows a connection of DMX floodlights –three per each DMX address. Each of the
three floodlights uses a separate ID address, allowing you to control the whole group with choosing a channel (3,
4, 6 or 8) or controlling each floodlight separately (when channel 11 is selected).

10
www.ultralux.bg
UPLOADING A PROGRAM
First, select the floodlight that is going to be leading (MASTER) and have its program prepared in the
EDIT menu beforehand. After that, connect all the floodlights with DMX cables, choose UPLOAD from the menu
of the MASTER floodlight and press ENTER. Its program would be transferred to all the floodlights in SLAVE
mode.
CONNECTING
The connection must be executed with XLR connectors on both ends (male and female).
WARNING: Do not connect the grid’s ground with the ground of the floodlight. This would cause the luminaire to
operate erratically. Test the polarity of the cables with an Ohm-meter.
3-pin to 5-pin conversion
When using a 5-pin connector you must also use an adapter. The chart below shows the correct way of
connecting the cables:
Conductor
3 Pin Female
(output)
5 Pin Male
(Input)
Ground/Shiel
d
Pin 1
Pin 1
Data ( - )
signal
Pin 2
Pin 2
Data ( + )
signal
Pin 3
Pin 3
Do not use
Do not use
Do not use
Do not use

11
www.ultralux.bg
MOUNTING
The area where the floodlight would be mounted must be able to hold 10 times its weight without being
deformed. When mounting, the floodlight must be additionally reinforced with a special mounting cable, in case
the mounting bracket breaks. Never stand directly under the floodlight when it is being mounted, dismounted, or
serviced. The proper mounting of the floodlight requires certain qualification and experience. Do not attempt to
mount the floodlight if you are not sure you can do it properly. The installation must be checked from a
competent person at least once a year.
The INNO POCKET SPOT technology allows a vertical mounting. To avoid damaging the luminaire or an eventual
accident DO NOT mount it sideways (see the illustration) or less than half a meter from flammable materials (e.g.
drapes)!
MECHANICAL PARAMETERS
TAKING CARE OF THE NATURAL ENVIRONMENT CLEANLINESS
•The product and its components are not harmful to the environment
•Please dispose the package elements separately in containers for the corresponding material.
•Please dispose the broken product separately in containers for out of usage electrical equipment.