Unicol RH200UHD User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for
pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface will support five times the
combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also
layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified use may result in failure or
personal injury. This product is intended for indoor use only. We recommend using a qualified trades
person for installation. Use an assistant or lifting equipment to lift and position products.
For support, please call: [phone] or email: [email protected]
Revised 22/01/21
01865 767676
[email protected]
www.unicol.com
*Please check model specific details before installing*
RH200UHD
Screen Size: 71-98” Guide Max. Weight: 200kg

01865 767676
[email protected]
www.unicol.com
2Revised 22/01/21
COMPONENTS
INSTALLERS REQUIRED
2-3
# DESCRIPTION QTY
1RH200UHD Heavy Duty Mast 1
2Heavy Duty Mount Arms 2
3Universal Screen Arms 4
4Stabilisation Arms 2
5Two Part Base Cover 1
6Heavy Duty Stand Base 1
7 Optional Accessories -
#TOOLS REQUIRED
1 Pozi Head Screwdriver
2 4mm & 5mm Allen Keys
3 19mm Spanner
4 17mm Spanner
12 3
45
7
6

01865 767676
[email protected]
www.unicol.com
3
Revised 22/01/21
STEP 1
Unlock and lift out front cabinet door. Remove
lower front panel by unscrewing 8x M6 screws and
put aside.
STEP 2
Connect base to mast as shown. For a trolley
version, tap castors with the rubber mallet until
they lock into place (ensure braked castors are at
the front).
Place the base cover over the screws on the base
and secure at the rear.
STEP 3
Remove the 4x screws from the top front panel and
put the panel aside.
Place equipment in the cabinet section at the
bottom and feed cables through the top, down the
mast and into the cabinet section.
STEP 4
Offer one of the mount arms up to the side of the
mast (lipped side facing the front) and secure into
position (as shown above) by accessing the nuts
from inside the mast.
Repeat for the other side.

4
01865 767676
[email protected]
www.unicol.com
Revised 22/01/21
STEP 8
Line the screen and arms up with the back plate
and offer it up at a slight angle - allowing the top of
the arms to hook over the lip of the back
plate. Gently lower the screen until the arms are
securely hanging on top of the back plate.
STEP 7
Locate the mounting holes on the back of your
screens. Line the two mounting arms up (ensure the
hook section is at the top of the screen, as shown)
and using the taglocks/two part spacers provided
and the manufacturer recommended screws, attach
the arms to the back of the screens.
STEP 6
Thread any cabling through the highlighted holes in
the top front panel. Screw the panel back into place
as shown and tighten.
STEP 5
**This must be done before fitting either screen
and should remain in the support position
(shown above) until both screens are fitted.**
Undo the handwheel at the back of the mount arm
to release the stabilisation arm. Pivot down and un-
fold. Screw handwheel into rear of arm (as shown)
to secure. Adjust the foot at the bottom so that it
rests flat on the ground. Repeat for the other side.

5
01865 767676
[email protected]
www.unicol.com
Revised 22/01/21
STEP 9
Once centered, adjust the level of the screen with
the two top screws on the mount arms. Once
levelled secure the screen by tightening the bottom
two screws.
STEP 10
When screens are fully secure, undo the handwheel
and fold the stabilisation arm back up. Reattach to
the back of the mount arm.
STEP 11
Finish cabling and resecure the bottom front panel.
Slot the cabinet door back into position and lock.