Unicol SBM User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your
carrier claims agent and do not continue the installation until it has been reviewed. Please watch for pinch
points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring
loaded parts. Before installing, make sure that the supporting surface will support five times the combined
load of the solution and the hardware. Never exceed the maximum load capacity. Please also layout all
components to ensure that you have all of the required parts before proceeding (see BOM list on following
page). Use of this product for anything other than its specified use may result in failure or personal
injury. This product is intended for indoor use only. We recommend using a qualified trades person for
installation. Use an assistant or lifting equipment to lift and position products.
For support, please call: [phone] or email: [email protected]
Revised 08/12/23
01865 767676
[email protected]
www.unicol.com
*Please check model specific details before installing*
SBM / SBC / SBT / VCSS / VCTS /
VCTST / VCM1 / VCMP / VCMT / MCM
Screen Size: n/a Guide Max. Weight: 10kg
Sound and Video Bar Mount pg 2-3
SBM clips onto PZX1 or PZX9 universal mounts
SBC for ceiling suspension
SBT bolt on style for twin screen trolleys
Video Conference & Sound Bar Mount pg 4-5
VCSS clip onto PZX1 or PZX9 universal mounts
1x VC camera + 1x sound bar
VCTS clip onto PZX1 or PZX9 universal mounts
1x VC camera + 2x sound bar
VCTST bolt on style for twin screen trolleys
1x VC camera + 2x sound bar
Video Conference Cameras pg 6-7
VCM1 bolt on style on universal or dedicated mount
VCMP clip onto PZX universal mount
VCMT bolt on style for twin screen trolleys
MCM for ceiling suspension

2Revised 08/12/23
COMPONENTS
01865 767676
[email protected]
www.unicol.com
INSTALLERS REQUIRED
1
# DESCRIPTION QTY
1SBM Rails 2
2SBM Clip-On Mount Unit 1
3SBM Mount Plate (Example) 1
4SBT Rails 2
5SBT Bolt-On Mount Unit 1
6SBT Mount Plate (Example) 1
7SBC Column Suspension Unit 1
8SBM Mount Plate (Example) 1
#TOOLS REQUIRED
14mm & 5mm Allen Keys
1
3
7 8
6
2 4 5

01865 767676
[email protected]
www.unicol.com
3
Revised 08/12/23
1
2
3
1
2
3
SBM1 / SBM9
Each style can be mounted with the devices above
or below the screen. Hook the assembled bracket
over the rail of the PZX screen mount back plate.1
Adjust the horizontal positioning to suit, then tighten
the screws underneath to secure into position.2
SBM & SBT GENERAL ASSEMBLY INSTRUCTIONS
Connect your device to mount plate3. Each mount
is dedicated to your device so may vary from the
image above.
Connect rails2to mount unit1. To adjust sound bar
height, simply fix in the slots that best suit.
Connect the mount plate3to the bottom of the rails2.
Next, follow either SBM1/SBM9 or SBT step.
SBC
1. Designed to fit to suspended columns from a
ceiling mount. Each mount plate1is dedicated to your
device so the brackets holes will align with those
situated on your device.
2. Remove through-bolt and loosen grub screws in
socket. Align fixing holes in socket and column and
fix with through-bolt. Tighten grub screws to finish.
SBT
The SBT fixes to the 4x 150x150mm centre holes on
the mast of some stands/trolleys. In some cases, this
may include a span bar unit. In this instance, screens
will need removing along with the bottom two fixings.
Loosen the top two fixings and slot the SBT tear-drop
holes over the bolts1. Line up the bottom two holes,
and secure fixings into place2. Tighten all fixings.
1
2
1
1
1
2
SBM
SBT
2

4Revised 08/12/23
COMPONENTS
01865 767676
[email protected]
www.unicol.com
INSTALLERS REQUIRED
1
# DESCRIPTION QTY
1VCSS Rails 2
2VCSS Clip-On Mount Unit 1
3VCSS Mount Plate (Example) 1
4VCTS Rails 2
5VCTS Clip-On Mount Unit 1
6VCTS Mount Plate (Example) 1
7VCTST Rails 2
8VCTST Bolt-On Mount Unit 1
9VCTST Mount Plate (Example) 1
#TOOLS REQUIRED
14mm & 5mm Allen Keys
1
7
2
8
3
9
4 5
6

01865 767676
[email protected]
www.unicol.com
5
Revised 08/12/23
GENERAL ASSEMBLY INSTRUCTIONS
Connect your device to mount plate3. Each mount
is dedicated to your devices so may vary from the
image above.
Connect rails2to mount unit1. To adjust sound/VC bar
height, simply fix in the slots that best suit.
Connect the mount plate3to the bottom of the rails2.
Finally, follow one of the next two steps depending
on which part code you are installing.
VCSS1 / VCSS9 / VCTS1 / VCTS9
Each style can be mounted with the devices above
or below the screen. Hook the assembled bracket
over the rail of the PZX screen mount back plate.1
Adjust the horizontal positioning to suit, then tighten
the screws underneath to secure into position.2
1
2
VCTST
The VCTST fixes to the 4x 150x150mm centre holes
on the mast of some stands/trolleys. In some cases,
this may include a span bar unit. In this instance,
screens will need removing as well as the bottom
two fixings.
Loosen the top two fixings and slot the VCTST
tear-drop holes over the bolts1. Line up the bottom
two holes, and secure fixings into place2. Tighten all
fixings.
1
2
1
11
22
2
3
3
3
VCSS VCTS VCTST

6Revised 08/12/23
COMPONENTS
01865 767676
[email protected]
www.unicol.com
INSTALLERS REQUIRED
1
# DESCRIPTION QTY
1VCM Typical Body 1
2VCM Platform (Example) 1
3VCM Adjustable Arm 1
4VCMP Clip-On Arm 1
5VCMP Platform (Example) 1
6VCMT Platform (Example) 1
7VCMT Adjustable Arm 1
8VCMT Bolt-On Body 1
9MCM Suspension Socket 1
10 MCM Platform (Example) 1
#TOOLS REQUIRED
14mm & 5mm Allen Keys
124
35
678
10
9

01865 767676
[email protected]
www.unicol.com
7
Revised 08/12/23
VCM1 / VCMT
1. The VCM can be fitted above or below the screen.
It sits between mast and mount, slotting over the top
2 bolts that attach the screen mount to the stand.
Loosen these bolts, slot the VCM in and tighten bolts.
2. Adjust the height of the platform by loosening
the 2 screws highlighted and tightening when in
position. Fix your VC camera to the platform to finish.
VCMP
1. The VCMP is a clip-on mount that can be fitted
above or below the screen. It has height adjustment
in the rails by removing 4 screws. Clip arm hook over
mount backplate rail.
2. Secure by tightening a screw at the bottom of
the mount backplate. Fix your VC camera to the
platform to finish.
MCM1
1. Designed to fit to a column suspended from a
ceiling mount. Fix your VC camera to the platform.
2. Remove through-bolt and loosen grub screws in
socket. Align fixing holes in socket and column and
fix with through-bolt. Tighten grub screws to finish.
12
21

Any Questions?
[phone] [email protected] unicol.com/instructions