Unilumin Upad III User manual

UpadIII product manual
www.unilumin.cn I
Revision History
No.
Version
Updated description
Date
1
Initial Edition
First published
2015.08.31
2
Second Edition
Optimized display structure
2016.11.14
Specifications and Contents are subject to change without notice.

UpadIII product manual
www.unilumin.cn II
Special Instruction
Thank you very much for choosing our product. In order to ensure your smooth use
process, please read the product manual carefully before using. While every effort has been put
to ensure the accuracy and reliability when compiling the manual, there still might be errors and
flaws, therefore, please understand that our company may modify and change the content of the
manual at anytime without notice. If you have any problems or suggestions in theprocess of use,
please contact us according to the contact information listed in this manual, and we will try our
best to support you in time on the problems you have encountered; and we sincerely appreciate
your suggestions and will make assessment to adopt your suggestions immediately.
Copyright
Copyright © 2016 Unilumin Group Co., Ltd. All rights reserved. The operating
software is based on Windows System. All brand, product, service names and logos are
trademarks and registered trademarks of their respective owners and are hereby recognized
and acknowledged.
Trademark
is a registered trademark of Unilumin Group Co., Ltd.

UpadIII product manual
www.unilumin.cn III
For indoor products, in order to use display correctly, please read the
following carefully.
WARNING!
The device may get damaged or lead to unrecovered while ignoring the warning.
1) Prohibit throwing or turning upside down when moving and storing.
2) Prohibit scratching and physical collision during installation.
3) Prohibit being exposed to dripping or splashing.
4) Prohibit putting display under air-condition outlet directly.
5) Prohibit putting it under volatile, corrosive, flammable chemicals environment.
6) Prohibit using the product in rainy outdoor and/or above 80% humidity environment.
7) Prohibit using water or chemical solvent to clean the equipments.
8) Prohibit using non-certified electrical equipments.
9) Make sure the display and its accessory devices connect earth wire.
10) When accident, such as abnormal smell, smoke, leakage, temperature rising, please shut
down the power immediately and contact with qualified person.
CAUTION!
Display is not able to work in best condition while ignoring the cautions.
1) Wearing gloves and static wrist strap during installation or doing maintenance.
2) When designing heat dissipation system, taking ventilation of the back of the display into
consideration.
3) Keep humidity under 80% when storage.
4) Use single phase power when the Max capacity less or equal than 3KW, otherwise should
be three phase power.
5) Make sure to use the display twice a week , each time over two hours’ light-up.
6) Display may be much more likely to fail and has shorter lifespan when installed at seaside,
saline, sulfur-containing gases zone, kitchen exhaust or some area which has a high
temperature difference between outside and inside. If inevitable, please contact with our
service network for professional advice.

UpadIII product manual
www.unilumin.cn IV
For outdoor products, in order to use the screen correctly, please read the
following carefully.
WARNING!
The device may get damaged or lead to unrecovered while ignoring the warning.
1) Prohibit throwing or turning upside down when moving and storing.
2) Prohibit scratching and physical collision during installation.
3) Prohibit flooding the screen.
4) Prohibit blow the screen when the air outlet of the air conditioning close against it.
5) Prohibit put it under the volatile, corrosive, flammable chemicals environment.
6) Prohibit use chemical solvent to clean equipment.
7) Prohibit use non-certified electrical equipment.
8) Make sure the equipment connect well and reliable with the earth before using.
9) When accident, such as abnormal smell, smoke, leakage, temperature rising, please shut
down the power immediately and contact with professionals.
CAUTION!
That the main factor on getting no wonderful performance is ignoring the caution.
1) Wearing gloves and static wrist strap during do the installation or maintenance.
2) Make sure the air circulation when do the cooling solutions.
3) Keep storage environment humidity under 80%, the air should be cool and dry.
4) Use single phase power when the Max capacity less or equal than 3KW, otherwise should
be three phase power.
5) Mare sure twice a week to use the screen and each time over two hours’ light up.
6) It may cause the device prone to failure and shorten service life when installed at seaside,
saline, sulfur-containing gases zone, kitchen exhaust or some area have a high temperature
difference between outside and inside. When it is inevitable, please contact with our
service network professionals.

UpadIII product manual
www.unilumin.cn V
Contents
1. PRODUCT INTRODUCTION..................................................................................1
1.1 FEATURES...............................................................................................................1
1.2 CABINET APPEARANCE...........................................................................................1
1.3 SPECIFICATION .......................................................................................................2
1.3.1 Indoor Product Specification ...........................................................................2
1.3.2 Outdoor Product Specification.........................................................................3
1.4APPLICATION..........................................................................................................4
2. INSTALLATION AND WIRING ..............................................................................5
2.1 PACKAGE CHECK-OUT............................................................................................5
2.2 GENERAL INSTALLATION ........................................................................................5
2.2.1 Floor Installation..............................................................................................5
2.2.2Hositing installation..........................................................................................9
2.3 PRODUCT WIRING ................................................................................................11
2.3.1 Common Wire................................................................................................11
2.3.2 Signal Wiring.................................................................................................12
2.3.3 Power Wiring.................................................................................................13
2.3.4 Flight Distribution Box Show........................................................................14
3. DISPLAY CONTROL-SETTING ...........................................................................16
3.1 CURRENT DETECTION ..........................................................................................16
3.2 DISPLAY SOFTWARE SETTING...............................................................................16
3.2.1 Start-Up .........................................................................................................16
3.2.2 Software Installation......................................................................................17
3.3DISPLAY SETTING.................................................................................................17
3.4 BRIGHTNESS SETTING ..........................................................................................22
3.5 CALIBRATION .......................................................................................................25
3.5.1 Set Coefficients for a New Scan Board (Receiving Card) .............................27
3.5.2 Set Coefficients for a New Module................................................................30
3.6 PRESTORE PICTURE ..............................................................................................32
4. DISPLAY PLAY-SETTING.....................................................................................34

UpadIII product manual
www.unilumin.cn VI
4.1 UNISTUDIO PLAY MODE ........................................................................................34
4.2 PLAYING SETTING ................................................................................................35
4.2.1 Display Window Setting ................................................................................35
4.2.2 Start Setting ...................................................................................................36
4.3 THE EDIT OF A PROFESSIONAL BROADCAST SCHEME.............................................37
4.3.1 Edit Segment..................................................................................................37
4.3.2 Editing Program Page....................................................................................38
4.3.3 Editing Window.............................................................................................40
4.3.4 Editing Media ................................................................................................43
4.3.5 Playing...........................................................................................................46
4.4 SAVE AND OPEN ...................................................................................................48
5. DISPLAY ON / OFF STEPAND MAINTENANCE ..............................................49
5.1 SWITCHING ON POWER SEQUENCE.......................................................................49
5.2 SWITCHING OFF POWER SEQUENCE......................................................................49
5.3 MAINTENANCE METHOD......................................................................................49
5.4 MAINTENANCE METHOD IF NOT USING FOR A LONG TIME.....................................50
5.4.1 Set Up Prestore Picture..................................................................................50
5.4.2 Open Up Aging Test.......................................................................................51
5.4.3 Display Brightness and Aging Time-table .....................................................52
6. TROUBLESHOOTING AND PARTS REPLACEMENT.......................................53
6.1 TROUBLE SHOOTING ............................................................................................53
6.1.1 The Whole Display Black out........................................................................53
6.1.2 Display Output Image Is Incomplete or Incorrect Position............................53
6.1.3 Display Output Image Blinking.....................................................................53
6.1.4 Individual Cabinet of the Display Showing Wrong Images or Flickering.....54
6.1.5 Individual Cabinet Does Not Light................................................................54
6.1.6 Certain Row of the Module or Individual Module Does Not Light...............54
6.2 MAIN PARTS REPLACEMENT.................................................................................55
6.2.1 Module Replacement for Indoor Product.......................................................55
6.2.2 Power Supply and Receiving Card Replacement for Indoor Product ............57
6.2.3 Module Replacement for Outdoor Product....................................................60

UpadIII product manual
www.unilumin.cn VII
6.2.4 Power Supply and Receiving Card Replacement for Outdoor Product .........63
6.2.5 Angle Block Replacement .............................................................................65
7. PACKAGE TRANSPORTATION AND STORAGE...............................................66
7.1 PACKAGE..............................................................................................................66
7.2 TRANSPORTATION.................................................................................................66
7.3 STORAGE..............................................................................................................66
FIGURE 1: PRODUCT WARRANTY CARD............................................................67
FIGURE 2: PATH OF SIGNAL CABLE INSIDE THE CABINET............................68

UpadIII product manual
www.unilumin.cn 1
1. Product Introduction
The series of UpadIII is high-end rental products with high-precision die-casting
aluminum design, lightweight ultra-thin, automatic cooling structure without fan design, good
heat dissipation, zero noise; cabinet with standard cabinet size, High-precision seamless
splicing, power signal interface outward 45 °, easy to plug; SMD lamp with black lights, wide
viewing angle, high contrast, soft images; box and box with wrench-type card lock connection,
convenient hand operation, magnetic suction auxiliary assembly between cabinets enable one
person handling, easy disassembly, module with calibration data storage function, convenient
on-site automatic calibration module data, to meet the fixed installation, seat installation,
lifting and other needs, to adapt to different application environments.
1.1 Features
1) Fully enclosed die casting aluminum, ultra-thin, high stability.
2) Low radiation, ultra-quiet, more safety used.
3) Wide color gamut, free adjustment on brightness and color temperature, Suitable for
various occasions.
4) Hoisting, floor installation and other kinds install style.
5) 45°outgoing power supply and signal plug interface design.
6) Seamless splicing for concave and convex, support flexible splicing between concave 5°
and convex 10°.
1.2 CabinetAppearance
Fig 1-1【Cabinet appearance】
1．Hanging latch
2．Top magnet
3．Cabinet handle
4．Locating pin
5．Signal socket
6．Cabinet handle
7．Power socket
8．Angle block
9．Screw hole
10．Bottom magnet
11．Locking plate
12．Edge protection pin
13．Left-right lock

UpadIII product manual
www.unilumin.cn 2
1.3 Specification
1.3.1 Indoor Product Specification
Parameter
UpadIII2.6
UpadIII3.2
UpadIII3.9
UpadIII4.8
Physical
Parameter
Pixel configuration
1R1G1B
LED type
3-in-1 Black SMD
Pixel density(dots)
147,456
97,344
65,536
43,264
Pixels per panel(dots)
192*192
156*156
128*128
104*104
Cabinet
size(W*H*D)/(mm)
500*500*86
Display area(㎡)
0.25
Material
Die-casting aluminum
Weight(kg)
9
Electronic
parameter
Grey scale (bit)
16
Refresh rate（Hz）
2880
2880
3840
2880
Drive type
1/16
1/13
1/8
1/13
Frame frequency（Hz）
50/60
Data interconnection
CAT5 cable:＜100 m; multi-mode fiber:＜300m; Single mode
fiber:＜10 km
Optical
parameter
Brightness（cd/m²）
1200
Color temperature（K）
2000-9300 adjustable
Contrast ratio
5000:1
Viewing Angle(°)
140/120
Electrical
parameter
Input voltage
AC 100～240
Input frequency（Hz）
50～60
Input power
<max/typical >(W/panel)
120/40
Circumstance
parameter
Storage temperature and
humidity(℃/RH)
-20～+55/10～80%
Operation temperature and
humidity(℃/RH)
-10～+45/10～80%
Ingress protection
IP30