Unior 1518 User manual

art. 1518
WARNING:
* always read the instruction before using power tools
* always wear safety googles
* wear hearing protection
OPERATING INSTRUCTION
1. Warn ng
1.1 Air pressure
The air pressure must be restricted at or less than maximum presure 90
psi (6.2 bar), do not exceed it.
1.2 Air line
Use an air hose between the compressor and the tool. The
corresponding hose internal diameter is recommended in the attached
table in the data sheet. Compressed air is cooled and its water content
separated as soon as the air leaves the compressor. However some of
the water is condensed in the piping, and can enter the tool mechanism
and cause damage. An air filter and on oiler should be installed between
the compressor and the tool. Use a recommended compressor in the
date sheet or larger for each tool.
1.3 Air hose
Clean the hose with a blast of compressed air before connecting the
hose to air tool. This will prevent both moisture and dust within the
hose from entering the tool an causing possible rust or malfunction. To
compensate for unusually long hose (over 25ft) the line pressure should
be increased accordingly.
1.4 Approved eye protection, mask, hearing protection and gloves shall
be worn when operate this tools.
1.5 The working place shall be ventilated.
1.6 Release the on-off device in case of air supply failure.
1.8 Use only a lubricant recommended by the manufacturer.
1/4" Pneumatic angle grinder
Art. Code Free speed Max. Air pressure Air consumption Air inlet Lenght Weight
1518 617730 11000 RPM 6,2 bar 170 l/min 1/4" 230 mm 1920 g
1.7 Release the start and stop switch in case of a failure of energy
supply.

2. Ma ntenance
2.1 Lubrication
Before connecting the hose, apply 4 to 5 drops of #60 spindle oil at the
inlet. Use of a thicker oil can lead to reduced performance of malfunction.
Also oil every 3 to 4 hours of operation.
2.2 Storage
Avoid storing the tool in a location subjected to high humidity. If the tool
is left as it is used, the residual moisture inside the tool can cause rust.
Before storing and after operation, oil the tool at the air inlet with spindle
oil and run it for a short time.
2.3 Ordering service part
For further operational and handling information or for replacement of
parts and components contact the outlet from where you purchased the
tool or the service division of your company.
Tool
Leader hose
Oil here daily Air hose Nipple
Coupler Oiler
Filter
WARNING:
1. The tool should not be used in potentially explosive atmospheres.
2. Disconnect the air hose before changing or adjusting anything.
3. Prevent loose clothes, long hair etc from coming into contact with the
revolving spindle, as this could cause injury.
4. Excessive high air pressure that exceeds the recommended maximum
pressure may cause injuries to the user.
5. eep your body in well balanced position and always wear gloves to
reduce the risk of becoming trapped due to torque between handle and
work piece.
6. Prolonged exposure to vibration can cause injury.
7. Slip/ trip/ fall is a major reason of serious injury. Beware of excess
hose left on the workplace floor.
8. Wearing correct breathing protection could avoid inhaling dust or
debris from work process that can be harmful to your health.

Warranty:
Unior d.d. offers one year free charge service warranty to products
supplied by Unior d.d. and authorized dealers.
All products are warranted under following conditions:
* one year from the date of purchase for tools with Unior brand name.
* the free charge service only applies to defects in material and
workmanship. The guarantee becomes invalid if the tool has been
improperly used or has been repaired using non genuine spare parts
and/or has been modified or repaired by someone other then UNIOR
d.d. authorized service representatives.
Spare parts:
EC Declarat on of Conform ty
Unior d.d.
ovaška cesta 10, 3214 Zreče, SLOVENIJA
Declares under its own responsibility that the following product,
Art cle 1518 - 1/4" Pneumat c angle gr nder
is in conformity with essential safety and health requirements of
council Directive 98/37/EEC, and folowing provisions of the
harmonized standards mentioned below: prEN792/ EN 292-1/
EN 292-2/ EN 28662/ DIN 45635-1/ DIN 45635-20 / ISO 8662.
Zreče, December 2006
Gorazd orošec, President
Name and signature of the authorized person
№ Code Description Qty.
1518.1 618015 Motor Housing 1
1518.2 618016 Seal plate 1
1518.3 618017 Ball Bearing 1
1518.4 618018 Arbor 1
1518.5 618019 Ball bearing 1
1518.6 618020 Woodruff key 1
1518.7 618021 Bevel Gear 1
1518.8 618022 Wave washer 1
1518.9 618023 External Stop ring 1
1518.10 618024 Gasket 1
1518.11 618025 Retainer 1
1518.12 618026 Center Wheel guard 1
1518.13 618027 Spring washer 5
1518.14 618028 Hex socket head cap bolt 5
1518.15 618029 Rotor 1
1518.16 618030 Front end plate 1
1518.17 618031 Cylinder 1
1518.18 618032 Spring pin 1
1518.19 618033 Rotor blade 4
1518.20 618034 Rear end plate 1
1518.21 618035 Governor 1
1518.22 618036 Pendulum 8
1518.23 618037 Spring pin 2
1518.24 618038 Plunger 1
1518.25 618039 Adjust screw 1
1518.26 618040 Spring 1
1518.27 618041 Adjust nut 1
1518.28 618042 Ball bearing 1
1518.29 618043 Bevel pinion 1
1518.30 618044 O-Ring 1
1518.31 618045 Exhaust deflector 1
1518.32 618046 Tapping screw 2
1518.33 618047 Plug 1
1518.34 618048 O-Ring 1
1518.35 618049 Flange 1
1518.36 618050 Grinding wheel 1
1518.37 618051 Flange nut 1
1518.38 618052 Handle 1
1518.39 618053 Wrench (A) 1
1518.40 618054 Wrench (B) 1
1518.41 618055 Ball Bearing 2
1518.42 618056 Throttle valve housing 1
1518.43 618057 Bushing 1
1518.44 618058 Air inlet bushing 1
1518.45 618059 Valve stem 1
1518.46 618060 Valve spring 1
1518.47 618061 Throttle housing 1
1518.48 618062 O-Ring 1
1518.49 618063 O-Ring 1
1518.50 618064 Throttle lever 1
1518.51 618065 Throttle lever lock 1
1518.52 618066 Torsion spring 1
1518.53 618067 Spring pin 1
1518.54 618068 Spring pin 1
1518.55 618069 Lock ring 1
1518.56 618070 Coupling nut 1