UniStrong Odin User manual

www.unistrong.com/english QuickStartforOdin
Odin Series Quick Start
1. Appearance
2. Operating steps：
I. Charging
II. Fix TF card/SIM card/battery
III．Turn on the collector
IV. Connect to PC to install application or data
V. Collect GIS data with internal GPS and GIS application
VI. Upload data
•Charging
Insert the Li-ion battery into the battery charger to charge.
Remark: mini USB cable can also be used to charge the receiver. When normally charged, there is
charging icon in the screen if receiver is off and there is charging icon to the top right corner in the screen
if receiver is on.
•Fix TF card/SIM card/Battery
1、Turn the back cover screw to the open position according to the instruction on the back
cover and take off the back cover(figure 1).
2、Fix the SIM card and TF card according to the instruction in the battery cabin(figure 2).
3、Fix the battery.
4、Fix the back cover and turn the back cover screw to the lock position according to the
底部
Mini USB socket
Touch panel
Antenna
Power
Front Back
Other function
keys Back cover
Speaker
Reset button
Earpiece Camera
Lanyar
d
tether point
Microphone
Start menu
Back stra
p
screws
Back stra
p
holde
r
Bottom
Back cover screw
External antenna
connector

www.unistrong.com/english QuickStartforOdin
instruction on the back cover(figure 1).
（Figure 1）
（Figure 2）
•Turn on/off collector
1、Make sure there is enough power in battery, or connect receiver to PC with mini USB
cable(with battery in).
2、Press power button for 3～5 seconds to turn on(until the boot screen appears)/ turn off.
Remark: if receiver is down, press the reset button in the bottom of receiver to reset.
•Connect to PC
1、Make sure Microsoft ActiveSync application has been installed in PC.
2、Connect receiver to PC with mini USB cable.
3、ActiveSync application connect receiver and PC automatically. There is icon
appears in the tool bar of PC and ‘Synchronization Setup Wizard’ appears meantime, click
‘Cancel’.
4、Click ‘Browse’to check the files in receiver, then transfer data between PC and
receiver.
•Install Application
1、Make sure Odin is connect with PC via ActiveSync.
2、Click install file on PC to start the installation. If the install file is compatible for mobile
device, copy the file into Odin and click to start the installation.
3、Select installation directory in Odin（‘Flash Storage’ is suggested）, click ‘install’.
Remark: it’s suggested to install the application in ‘Flash Storage’, save data in TF card.
•Use GPS
Option 1
Use the internal GPS settings.

www.unistrong.com/english QuickStartforOdin
1. Start->Settings->System->GPS Settings->Satellite State
2. Click ‘Please click here to startup A-GPS’.
3. Wait until get GPS information.
•
Option 2
Use user-define application software: Set COM port as COM6 and baud rate as
57600 in application.
Here take ‘u-center mobile’application software for example.
1. Install ‘u-center mobile’and run it.
2. Set Port and Baud rate in ‘Rx’menu.

www.unistrong.com/english QuickStartforOdin
3. Wait until get GPS information.
•Use Camera
Select ‘Start->Picture & Video’，select ‘Camera’or camera icon to take photos. Click
screen and select ‘OK’to exit.
•Wireless Connection（Bluetooth/GPRS/WIFI）
Bluetooth
1、Select ‘Start->Settings->Connections->Wireless management’, click the icon
on the right of ‘Bluetooth’to activating the Bluetooth device.
2、Select ‘Start-> Settings-> Bluetooth’, click ‘Add new device…’, system will
search available Bluetooth device. Select the device in refurbished list and click ‘Next’
in the bottom right corner, input password.
3、Select ‘Next’, input password in external Bluetooth device and finish the connection.
Remark: The password is used to the connection between Bluetooth devices and can be setup freely,
such as ‘1234’.

www.unistrong.com/english QuickStartforOdin
GPRS
1、Make sure there's SIM card in receiver.
2、Select ‘Start->Settings->Connections->Connections’.
3、Click ‘Add a new modem connection’.
4、Input connection name, select ‘Cellular Line(GPRS)’, click ‘Next’.
5、Input ‘cmnet’, click ‘Next’.
6、Click ‘Finish’and add new connection successfully.
7、Click ‘Manage existing connections’.
8、Click on the new connection for a while and select ‘Connect’.
9、There is GPRS identifier on the signal icon on the top right corner, indicates the
successful connection.
WIFI
1、Select 'Start->Settings->Connections->Wi-Fi'；
2、Click ‘Search for Networks’, select a network that listed. Follow the installation
guide to input password and finish the connection.
3. Useful Settings
Screen response
Select ‘Start-> Settings-> System-> Screen’, click ‘Align Screen’icon and follow the
guide to align the screen.
Adjust backlight
Select ‘Start-> Settings-> System-> Backlight', adjust backlight status according to the
guild.
Auto power off
Select ‘Start-> Settings-> System-> Power-> Advanced’, set the power off time in
different conditions.
Remove programs
Select ‘Start-> Settings-> System-> Remove Programs’, select the program in the list
and click ‘OK’to remove.
Fall alarm
Select ‘Start-> Settings-> System-> Motion Sensor’, select ‘Fall Alarm’, check or
not the function of sharp warning sound when Odin is dropped. You can also open or
close the ‘Screen rotation’function in this menu.
Restore Factory Defaults
Select ‘Start-> Settings-> System-> Restore Factory Defaults’, restore factory defaults
settings according to the guide.
Caution: Restore factory defaults settings, all the data and programs will be lost.

www.unistrong.com/english QuickStartforOdin
4. Environmental
• Operating temperature: -10℃~+60℃
• Storage temperature: -30℃~+70℃
• Drop: 1.5m drop onto all faces
• Casing: Dustproof and resistant to heavy wind driven rain per IP66 standard
• Humidity: 5% ~ 95% (non-condensing)

www.unistrong.com/english QuickStartforOdin
Appendix‐Product Safety Warnings
Safety and compliance information
Use responsibility –Read all instructions and safety information before use to avoid
injury.
Battery safety
Charge battery only in temperature ranging from 32℉to 140℉(0℃to 60℃)
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type of battery recommended by the manufacturer.
The maximum operating ambient temperature of the switching power supply declared by the manufacturer
is 50 ℃.
Dispose of used batteries according to battery manufacturer’s instructions.
WiFi safety
Turn WiFi off in areas where WiFi use is prohibited or when it may cause interference or
danger, such as in airplanes while flying.
Care and maintenance
Odin is an electronic product and should be treated with care, to reduce the risk of fire,
electronic shock, or product damage.
•Do not expose this device to rain, moisture, or any type of liquid that corrodes
electronic circuits. If your device gets wet, immediate turn the power off. Allow the
device to dry completely before using it again.
•Clean the display with a soft cloth, and be careful not to wipe the display with
anything abrasive.
•Do not expose your device to extreme heat（－１０℃ ）or cold（６０℃）. For example, do
not leave it in the trunk of your car in high heat conditions.
•Do not attempt to open the device other than as instructed in this manual.
•Rough handling can break internal circuitry.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the
device.
•Use only the recommended accessories.
•Do not excessive sound pressure from earphones and headphones, which can cause
hearing loss.

www.unistrong.com/english QuickStartforOdin
USB Data Cables
ThisversionsupportstheUSBinterface.YoucanconnectyourOdinwiththe
PCviatheUSB&datacable,copyingormovingthefilesamidtheOdinandPC,or
browsingtheimages,recordfilesandvideofilessavedintheOdinviathePC.
1InserttheUSBdatacableconnectorintotheUSBinterfaceoftheOdin.
2ConnecttheotherterminaloftheUSBdatacablewiththeUSBinterfaceofthePC.

CAUTION
THECONNECTIONTOUSBINTERFACESHASTOBELIMITEDTO
USB2.0VERSIONORHAIGHER
THECONNECTIONTOSOCALLEDPOWERUSEISPROHIBITED
For more information, please turn to
www.unistrong.com/English
Email: [email protected]

Compliance with FCC Regulations
FCC Section 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment doescause harmful interference to radio or
television reception, which can be determined by turningthe equipment off and on, the user is
encouraged to try to correct the interference by one ormore of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Section 15.21 Information to the user
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Section 15.19 Labelling requirements
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference received,
including interference that may causeundesired operation.
SAR INFORMATION
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
Device types MG758/MG75X/MG75875075X/MG752/E750 (FCC ID: YYEMG75875075X ) has also
been tested against this SAR limit.
The highest SAR value reported under this standard during product certification
for use at the ear is 0.576 W/kg and when properly worn on the body is 1.194 W/kg. This device was
tested for typical body-worn operations with the back of
the handset kept 1.5cm from the body. To maintain compliance with FCC RF
exposure requirements, use accessories that maintain a 1.5cm separation
distance between the user's body and the back of the handset. The use of belt
clips, holsters and similar accessories should not contain metallic components in
its assembly. The use of accessories that do not satisfy these requirements may
not comply with FCC RF exposure requirements, and should be avoided.