United States Stove Company 2000 User manual

6 Ussc
ASSEMBLY INSTRUCTIONS
Blower Assembly
THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE
ATTEMPTING THE INSTALLATION.
THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE.
DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT SURFACES!
Step 1.
Fix the assembly to the back of the stove with the four screws provided.
Pedestal Trim Assembly
Assemble trim pieces as shown with the screws provided
in the parts bag. Washers may not be necessary.
After trim assembly, attach to the pedestal base at
the location shown using the screws provided.
Ash Pan Assembly
Remove ash pan from rebox. Under the rebox, there
are two brackets; Slide the ash pan into these brackets.

Ussc 7
INSTALLATION
SAFETY NOTICE
• IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO
REDUCETHERISKOFFIRE,FOLLOWTHEINSTALLATIONINSTRUCTIONS.
• CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT
PERMITS, RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA.
• USESMOKEDETECTORSINTHEROOMWHEREYOURSTOVEISINSTALLED.
• KEEPFURNITUREANDDRAPESWELLAWAYFROMTHESTOVE.
• NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL
LIGHTERFLUID,ORSIMILARLIQUIDSTOSTARTOR“FRESHENUP”AFIREINTHIS
HEATER.KEEPALLSUCHLIQUIDSWELLAWAYFROMTHEHEATERWHILEITISIN
USE.
• IN THE EVENT OF A CHIMNEY FIRE, PUSH THE AIR CONTROL FULL CLOSED TO
DEPRIVETHEFIREOFOXYGEN.CALLTHEFIREDEPARTMENT.
• DONOTCONNECTTOANYAIRDISTRIBUTIONDUCTORSYSTEM.
• ASOURCEOFFRESHAIRINTOTHEROOMORSPACEHEATEDSHALLBEPROVIDED
WHENREQUIRED.
POSITIONING THE STOVE
It is very important to position the wood stove as close as possible to the chimney, and in an area
thatwillfavorthemostefcientheatdistributionpossiblethroughoutthehouse.Thestovemust
therefore be installed in the room where the most time is spent, and in the most spacious room
possible. Recall that wood stoves produce radiating heat, the heat we feel when we are close to a
wood stove. A wood stove also functions by convection, that is through the displacement of hot air
accelerated upwards and its replacement with cooler air. If necessary, the hot air distribution from
the stove may be facilitated by the installation of a blower.
The wood stove must not be hooked up to a hot air distribution system since an excessive
accumulation of heat may occur.
A wood stove must never be installed in a hallway or near a staircase, since it may block the
way in case of re or fail to respect required clearances.

8 Ussc
FLOOR PROTECTOR
Your wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For
multiple layers, add R-values of each layer to determine the overall R-value. The R value for the
requiredboardis1.2.Ifthereisahorizontalsectionofchimneyconnector,theoorprotectorshould
go under it and 2 inches beyond each side
ConvertspecicationtoR-value:
k-factor is given with a required thickness (T) in inches: R=1/k x T
C-factor is given: R=1/C
Example:
 If the oor protector is 4” brick with a C-factor of 1.25 over 1/8” mineral board with a “k”
factor of 0.29 the total R-value of the system is:
4” brick C=1.25, R=1/1.25=0.8
1/8” mineral board K=0.29, R=1/0.29 x 0.125=0.431
Total R = Rbrick + Rmineral = 0.8 + 0.431 = 1.231
Total R is greater than 1.2, the system is acceptable.
Theoorprotectorshouldexceedthestoveasfollows:
Model Front Sides Rear
2000 25”
(635mm)
8”
(203mm)
¶6”
(152mm)
2500 26”
(660mm)
8”
(203mm)
¶6”
(152mm)
¶ - Canadian installations require 8” (203mm)

Ussc 9
CLEARANCES TO COMBUSTIBLES
It is of utmost importance that the clearances to combustible materials be strictly adhered to during
installation of the stove. Refer to the tables below :
• Floortoceilingheightmustbeatleast7’(2.13m)inallcases.
• Donotplaceanycombustiblematerialwithin4’(1.2m)ofthefrontoftheunit.
• Theclearancebetweentheuepipeandawallarevalidonlyforverticalwallsandforverticalue
pipe.
• Thechimneyconnectormustnotpassthroughanatticorroofspace,closetorsimilarconcealed
space,aoor,oraceiling.
• ForCanadianinstallations,wherepassagethroughawall,orpartitionofcombustibleconstruction
is desired, the installation must conform to CAN/CSA-B365.
• Auepipecrossingacombustiblewallmusthaveaminimumclearanceof18”(457.2mm).
• Toreduceueclearancesfromcombustiblematerials,contactyourlocalsafetydepartment.
Single Wall Pipe (Double Wall Pipe)
Model ABC D E F
2000 20(14)
(508mm(356mm))
22(20)
(559mm(508mm))
22.5(16.5)
(572mm(419mm))
32(30)
(813mm(762mm))
12(11)
(305mm(279mm))
22(21)
(559mm(533mm))
2500 12
(305mm)
20
(508mm)
16
(406mm)
30
(762mm)
10.5
(267mm)
20
(508mm)

10 Ussc
CHIMNEY CONNECTOR (STOVE PIPE)
Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this
is not the case, we recommend you contact your dealer in order to insure there will be no problem
with the draft.
The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or
0.53 mm. It is strictly forbidden to use galvanized steel.
Your smoke pipe should be assembled in such a way that the male section (crimped end) of the pipe
faces down. Attach each of the sections to one another with three equidistant metal screws.
The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch
per foot, with the upper end of the section toward the chimney. Any installation with a horizontal
run of chimney pipe must conform to NFPA 211. You may contact NFPA (National Fire Protection
Association) and request the latest edition of the NFPA Standard 211.
To insure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m
to 3.04 m). (Except for cases of vertical installation, cathedral-roof style where the smoke exhaust
system can be much longer and connected without problem to the chimney at the ceiling of the room).
There should never be more than two 90 degrees elbows in the smoke exhaust system.
Installation of a “barometric draft stabilizer” (replace register) on a smoke exhaust system is
prohibited.
Furthermore, installation of a draft damper is not recommended. Indeed, with a controlled combustion
wood stove, the draft is regulated upon intake of the combustion air in the stove and not at the exhaust.

Ussc 11
CHIMNEY
Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a fac-
torybuiltchimney,itmustcomplywithUL103orCSA-B365standard;thereforeitmustbeaTypeHT
(2100°F).Itisextremelyimportantthatitbeinstalledaccordingtothemanufacturer’sspecications.
Ifyouareusingamasonrychimney,itisimportantthatitbebuiltincompliancewiththespecica-
tionsoftheNationalBuildingCode.Itmustbelinedwithreclaybricks,metalorclaytilessealed
togetherwithrecement.(Rounduesarethemostefcient).
Theinteriordiameterofthechimneyuemustbeidenticaltothestovesmokeexhaust.Auewhich
istoosmallmaycausedraftproblems,whilealargeuefavoursrapidcoolingofthegas,andhence
thebuild-upofcreosoteandtheriskofchimneyres.Notethatitisthechimneyandnotthestove
which creates the draft effect; your stove’s performance is directly dependent on an adequate draft
from your chimney.
The following recommendations may be useful for the installation of your chimney:
1. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
2. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.
3. The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m)
distance by a height of 2’ (0.6m).
4. Installation of an interior chimney is always preferable to an exterior chimney. Indeed, the
interior chimney will, by denition, be hotter than an exterior chimney, being heated up
by the ambient air in the house. Therefore the gas which circulates will cool more slowly,
thus reducing the build-up of creosote and the risk of chimney res.
5. The draft caused by the tendency for hot air to rise will be increased with an interior chim-
ney.
6. Using a re screen at the extremity of the chimney requires regular inspection in order
to insure that it is not obstructed thus blocking the draft, and it should be cleaned when
used regularly.

12 Ussc
FACTORY BUILT CHIMNEY :
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be
followed. You must also purchase (from the same manufacturer) and install the ceiling support
packageorwallpass-throughand“T”sectionpackage,restops(whereneeded),insulationshield,
roofashing,chimneycap,etc.Maintainproperclearancetothestructureasrecommendedbythe
manufacturer. The chimney must be the required height above the roof or other obstructions for
safety and proper draft operation.

Ussc 13
MASONRY CHIMNEY :
Ensure that a masonry chimney meets the minimum standards of the National Fire Protection As-
sociation (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose
mortarorothersignsofdeteriorationandblockage.Havethechimneycleanedbeforethestoveis
installed and operated. When connecting the stove through a combustible wall to a masonry chim-
ney, special methods are needed.

14 Ussc
Combustible Wall Chimney Connector Pass-Throughs
Method A. 12” (304.8 mm) Clearance to Combustible Wall Mem-
ber: Using a minimum thickness 3.5” (89 mm) brick and a 5/8”
(15.9 mm) minimum wall thickness clay liner, construct a wall pass-
through. The clay liner must conform to ASTM C315 (Standard
SpecicationforClayFireLinings)oritsequivalent.Keepamini-
mum of 12” (304.8 mm) of brick masonry between the clay liner and
wall combustibles. The clay liner shall run from the brick masonry
outersurfacetotheinnersurfaceofthechimneyuelinerbutnot
past the inner surface. Firmly grout or cement the clay liner in place
tothechimneyueliner.
Method B. 9” (228.6 mm) Clearance to Combustible Wall Member:
Using a 6” (152.4 mm) inside diameter, listed, factory-built Solid-
Pak chimney section with insulation of 1” (25.4 mm) or more, build
a wall pass-through with a minimum 9” (228.6 mm) air space be-
tween the outer wall of the chimney length and wall combustibles.
Use sheet metal supports fastened securely to wall surfaces on all
sides, to maintain the 9” (228.6 mm) air space. When fastening
supports to chimney length, do not penetrate the chimney liner (the
inside wall of the Solid-Pak chimney). The inner end of the Solid-
Pakchimneysectionshallbeushwiththeinsideofthemasonry
chimney ue, and sealed with a non-water soluble refractory ce-
ment. Use this cement to also seal to the brick masonry penetra-
tion.
Method C. 6” (152.4 mm) Clearance to Combustible Wall Member:
Starting with a minimum 24 gage (.024” [.61 mm]) 6” (152.4 mm)
metal chimney connector, and a minimum 24 gage ventilated wall
thimble which has two air channels of 1” (25.4 mm) each, construct
a wall pass-through. There shall be a minimum 6” (152.4) mm sep-
arationareacontainingberglassinsulation,fromtheoutersurface
of the wall thimble to wall combustibles. Support the wall thimble,
and cover its opening with a 24-gage minimum sheet metal sup-
port. Maintain the 6” (152.4 mm) space. There should also be a
supportsizedtotandholdthemetalchimneyconnector.Seethat
the supports are fastened securely to wall surfaces on all sides.
Make sure fasteners used to secure the metal chimney connector
donotpenetratechimneyueliner.
Method D. 2” (50.8 mm) Clearance to Combustible Wall Mem-
ber: Start with a solid-pak listed factory built chimney section at
least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more,
and an inside diameter of 8” (2 inches [51 mm] larger than the 6”
[152.4 mm] chimney connector). Use this as a pass-through for
a minimum 24-gauge single wall steel chimney connector. Keep
solid-pak section concentric with and spaced 1” (25.4 mm) off the
chimney connector by way of sheet metal support plates at both
ends of chimney section. Cover opening with and support chimney
section on both sides with 24 gage minimum sheet metal supports.
See that the supports are fastened securely to wall surfaces on all
sides.Makesurefastenersusedtosecurechimneyueline.
NOTES:
1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section
throughthewallpass-throughsystemandthechimneywall,tobutnotpasttheinneruelinerface.
2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed
space,oraoor,orceiling.

Ussc 15
OUTSIDE COMBUSTION AIR
Your wood stove is approved to be installed with an outside air intake which is necessary for a mobile
home. This type of installation is also required in air tight houses and houses with negative pressure
problems. You can purchase this option through your heater dealer. Make sure to specify the part
number mentioned in this booklet. Installation instructions are supplied with the air intake kit.
Outside combustion air may be required if :
1. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur
whether or not there is combustion present.
2.Existingfuel-redequipmentinthehouse,suchasreplacesorotherheatingappliances,smell,
do not operate properly, suffer smoke roll-out when opened, or back-drafts occur whether or not
there is combustion present.
3. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.
4.Thehouseisequippedwithawell-sealedvaporbarrierandtightttingwindowsand/orhasany
powered devices that exhaust house air.
5. There is excessive condensation on windows in the winter.
6. A ventilation system is installed in the house.
For use in MOBILE HOMES (U. S. installations ONLY):
• WARNING! DO NOT INSTALL IN SLEEPING ROOM.
• CAUTION! THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND
CEILING/ROOF MUST BE MAINTAINED.
• INSTALLINACCORDANCEWITH24CFR,PART3280(HUD).
• USE A FACTORY BUILT CHIMNEY THAT COMPLIES WITH UL 103 STAN DARDS;
THEREFOREITMUSTBEATYPEHT(2100°F).
• USEASPARKARRESTER.
• THESTOVEMUSTBEATTACHEDTOTHESTRUCTUREOFTHEMOBILEHOME.USE
THEFOUR(4)HOLESINTHEBOTTOMFLANGESOFTHEHEATER’SPEDESTALTO
SECURETHEUNITTOTHEFLOOR.THENINTALL/RE-INSTALLTHETRIM.
NONCOMBUSTIBLE FLOORING
Illustration: Securing heater to the Floor.

16 Ussc
TYPE WEIGHT
(LBS. CU. FT.,
DRY)
PER CORD EFFICIENCY
RANKING
SPLITS MILLIONS
BTU’s/CORD
Hickory 63 4500 1.0 Well 31.5
White Oak 48 4100 .9 Fair 28.6
Red Oak 46 3900 .8 Fair 27.4
Beech 45 3800 .7 Hard 26.8
Sugar Maple 44 3700 .6 Fair 26.2
Black Oak 43 3700 .6 Fair 25.6
Ash 42 3600 .5 Well 25.0
Yellow Birch 40 3400 .4 Hard 23.8
Red Maple 38 3200 .3 Fair 22.6
Paper Birch 37 3100 .3 Easy 22.1
Elm/Sycamore 34 2900 .2 VeryDifcult 20.1
Red Spruce 29 1800 .1 Easy 16.1
WOODSTOVE UTILIZATION
Yourheatingunitwasdesignedtoburnwoodonly;noothermaterialsshouldbeburned.Wasteandotherammable
materialsshouldnotbeburnedinyourstove.Anytypeofwoodmaybeusedinyourstove,butspecicvarietieshave
better energy yields than others. Please consult the following table in order to make the best possible choice.
It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried
for 9 to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very
important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily dry, if
it has been stored in poor conditions. Under extreme conditions it may rot instead of drying. This point cannot be over
stressed; the vast majority of the problems related to the operation of a wood stove is caused by the fact that the wood
used was too damp or had dried in poor conditions. These problems can be:
- ignition problems
-creosotebuild-upcausingchimneyres
- low energy yield
- blackened windows
- incomplete log combustion
Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be stored
directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between each row of
logs, which should be placed in the sunniest location possible. The upper layer of wood should be protected from the
elements but not the sides.
TESTING YOUR WOOD
Whenthestoveisthoroughlywarmed,placeonepieceofsplitwood(aboutveinchesindiameter)paralleltothedoor
on the bed of red embers.
Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds
from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your wood is damp.
If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut. Do not use
this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating potential conditions
forachimneyre.

Ussc 17
THE FIRST FIRES
The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only
burnsmallresinyourstovefortherstfourhoursofoperation.Neveropentheaircontrolmorethannecessaryto
achieve a medium burn rate.
Makesurethatthere’senoughaircirculationwhilecuringthestove.Theodorscouldbesmelledduringthe3or4rst
res.Neverstartyourstoveoutside.Youwillnotbeabletoseeifyouareoverheating.
IGNITION
After making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled
sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper
in the form of a tent. You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product
shouldbeusedtolightthere.
Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done in order to
avoid back draft problems often due to negative pressure in the house. If such is the case, open a window slightly near
the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as
possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement
is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.
When you have achieved a good bed of hot embers, we recommend the following burn procedures:
HEATING
Controlledcombustionisthemostefcienttechniqueforwoodheatingbecauseitenablesyoutoselectthetypeof
combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is adjusted
to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will burn quickly if
the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. The air intake control on
your stove is very simple. If you pull on it out completely towards you, it is fully open. If you push on it until it stops the
combustion air is reduced to a minimum. Real operating conditions may give very different results than those obtained
during testing according to the species of wood used, its moisture content, the size and density of the pieces, the length
of the chimney, altitude and outside temperature.
2000
Primary Air Settings
(Slide Damper is located in center of stove under hearth plate)
(Damper Adjustment: Pulling out on damper increases air)
Electric Blower Speed Setting (Variable)
(BlowerisonHighwhenturned“ON”, Rotate clock-
wiseuntilstopfor“LOW”.)
Burn Rate Adjust Damper from fully closed Burn Time Blower Speed
Low 1/4” (6.3mm) @ 30 minutes Low
Medium - Low 3/8” (9.5mm) @ 30 minutes Low
Medium-High 1/2” (12.7mm) @ 30 minutes Low
High approx. 3” (76mm) all minutes High
2500
Burn Rate Adjust Damper from fully closed Burn Time Blower Speed
Low 1/32” (1mm) @ 30 minutes Low
Medium - Low 1/16” (1.5mm) @ 30 minutes Low
Medium-High 5/16” (8mm) @ 30 minutes Low
High approx. 3” (76mm) all minutes High
CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so could
result in heater damage and will void your warranty.

18 Ussc
WARNINGS
• NEVEROVERFIREYOURSTOVE.IFANYPARTOFTHESTOVESTARTSTOGLOWRED,
OVERFIRINGIS HAPPENING.READJUSTTHE AIRINTAKECONTROL ATALOWER
SETTING.
• THEINSTALLATIONOFALOGCRADLEorGRATESISNOTRECOMMENDEDINYOUR
WOOD STOVE. BUILD FIRE DIRECTLY ON FIREBRICK.
• NEVERPUTWOODABOVETHEFIREBRICKLININGOFTHEFIREBOX.
RELOADING
Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the
air controls to maximum a few seconds prior to opening the stove’s door. Then proceed by opening
the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to
increase the draft and thus eliminate the smoke which is stagnant in a state of slow combustion in
the stove. Then bring the red embers to the front of the stove and reload the unit.
For optimal operation of your wood stove, we recommend you to operate it with a wood load
approximatelyequivalenttotheheightofrebricks.
It is important to note that wood combustion consumes ambient oxygen in the room .In the case of
negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly
or by installing a fresh air intake system on an outside wall.
Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and
other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors
condenseintherelativelycoolchimneyueofaslow-burningre.Asaresult,creosoteresidue
accumulatesontheuelining.Whenignitedthiscreosotemakesanextremelyhotre.Thechimney
connector and chimney should be inspected at least once every two months during the heating season
to determine if a creosote build-up has occurred. If creosote has accumulated (3mm or more), it
shouldberemovedtoreducetheriskofachimneyre.
We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe,
approximately 18” above the stove. This thermometer will indicate the temperature of your gas
exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere
between 275°F and 500°F. Below these temperatures, the build-up of creosote is promoted. Above
500 degrees, heat is wasted since a too large quantity is lost into the atmosphere.
TO PREVENT CREOSOTE BUILD UP
• Alwaysburndrywood.Thisallowscleanburnsandhigherchimneytemperatures,thereforeless
creosote deposit.
• Leavetheaircontrolfullopenforabout5min.everytimeyoureloadthestovetobringitbackto
properoperatingtemperatures.Thesecondarycombustioncanonlytakeplaceifthereboxishot
enough.
• Alwayscheckforcreosotedepositonceeverytwomonthsandhaveyourchimneycleanedatleast
once a year.
Ifachimneyorcreosotereoccurs,closealldampersimmediately.Waitfortheretogooutand
the heater to cool, then inspect the chimney for damage. If no damage results, perform a chimney
cleaning to ensure there is no more creosote deposits remaining in the chimney.

Ussc 19
ASH DISPOSAL
Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep.
Always empty the stove when it is cold, such as in the morning. Ashes should be placed in a metal
containerwithatightttinglid.Theclosedcontainerofashesshouldbeplacedonanoncombustible
oororontheground,wellawayfromallcombustiblematerials,pendingnaldisposal.Iftheashes
are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the close
container until all cinders have thoroughly cooled. Other waste shall not be placed in this container.
CAUTIONS:
• ASHESCOULDCONTAINHOTEMBERSEVENAFTERTWODAYSWITHOUTOPERATINGTHE
STOVE.
• THEASHPANCANBECOMEVERYHOT.WEARGLOVESTOPREVENTINJURY.
• NEVERBURNTHESTOVEWITHTHEASHTRAPOPEN.THISWOULDRESULTINOVERFIRING
THESTOVE.DAMAGETOTHESTOVEANDEVENHOUSEFIREMAYRESULT.
MAINTENANCE
Yourwoodstoveisahighefciencystoveandthereforerequireslittlemaintenance.Itisimportant
to perform a visual inspection of the stove every time it is emptied, in order to insure that no parts
have been damaged, in which case repairs must be performed immediately. Inspect and clean the
chimney and connector pipe periodically for creosote buildup or obstructions.
GLASS
• Inspectandcleantheglassregularlyinordertodetectanycracks.Ifyouspotone,turnthestove
off immediately. Do not abuse the glass door by striking or slamming shut. Do not use the stove if
the glass is broken.
• If the glass on your stove breaks, replace only with the glass supplied from your heater dealer.
Never substitute other materials for the glass.
• Toreplacetheglass,removethescrewsretainingtheglassmouldingsinsidethedoor.Remove
the mouldings and replace the damaged piece with a new one. Perform the procedure backwards
after replacing. When replacing the glass, you should change the glass gasket to make sure you
keep it sealed.
• Neverwashtheglasswithaproductthatmayscratch.Useaspecializedproduct,availableinthe
stores where wood stoves are sold. The glass should be washed only when cold.
GASKETING
It is recommended that you change the door gasket (which makes your stove door air tight) once
ayear,inordertoinsuregoodcontroloverthecombustion,maximumefciencyandsecurity.To
change the door gasket, simply remove the damaged one. Carefully clean the available gasket
groove, apply a high temperature silicone sold for this purpose, and install the new gasket. You may
light up your stove again approximately 24 hours after having completed this operation.
WARNING:
• NEVEROPERATETHESTOVEWITHOUTAGASKETORWITHABROKENONE.DAMAGE
TOTHESTOVEOREVENHOUSEFIREMAYRESULT.
PAINT
Onlycleanyourstovewithadrysoftcloththatwillnotharmthepaintnish.Ifthepaintbecomes
scratched or damaged, it is possible to give your wood stove a brand new look, by repainting it with
a1200°Fheatresistantpaint.Forthispurpose,simplyscrubthesurfacetoberepaintedwithne
sand paper, clean it properly, and apply thin coats (2) of paint successively.

20 Ussc
REPAIR PARTS
567
432
17
18
19
20
21
13
12
27
28
30
29
16
15
37
1
22
24 25 26
35
32 33
34
36
31
14
23
9
8
10
11
4
3
1
5
6
7
2
9
8
10
11
Feed Door Assembly

Ussc 21
REPAIR PARTS
Key Part No. Description Qty.
1 25491 Feed Door, Painted (40484) 1
2 25692 Handle, Painted (40515) 1
3 83506 3/8 x 1-1/4 Roll Pin 1
4891135 Spring Handle - LG 1
588066 Rope Gasket - 5/8” 4.6 Ft
688087 Glass Gasket - 1/8 thk x 1” wide 3.7 Ft
7 891131 Ceramic Glass 1
825464 Top Glass Retainer 1
9 25465 Bottom Glass Retainer 1
10 83202 10-24 x 3/8 Pan Head Phillips Screw 4
11 83278 Washer - 7/32 ID x 1/2 OD 4
1 69515MB Feed Door Assy. 1
225080B Feed Door Latch 1
3 83508 5/16-18 x 3/4 Hex Head Bolt 1
483338 5/16-18 Lock Nut 1
5891373 Door Hinge Pad 2
683045A Washer, 3/8” ID x 7/8” OD 2
7 83274 3/8-16 Lock Nut 2
8 86643 Tube, Secondary Air (Ø0.16
holes)
2000 1
2500 2
986645 Tube, Secondary Air (Ø0.22
holes)
2000 2
2500 2
10 891515 Retainer, Tube (1 per Secondary Tube) 3 - 5
11 88146 Refractory Insulation
2000 1
88138 2500 1
12 891516 Damper Slide 1
13 891517 Hearth Plate 1
14 891331 Spring Handle - Small 1
15 891514 Shield, Rear 1
16 891528 Air Deector 1
17 40292A Flue Collar 1
18 88032 Flue Collar Gasket 1.7 Ft
19 83432 5/16-18 x 1-1/2 Hex Head Bolt 3
20 83045 Washer, 5/16” ID x 3/4” OD 3
21 83431 Weld Tab 3
22 89066 Firebrick (4.5 x 9 x 1.25)
2000 16
2500 18
23 891414 Firebrick (2-1/4 x 9) 2
24 24103 Firebrick (4-1/2 x 4-1/2) 1
25 891530 Firebrick (4-1/2 x 7-1/2 ) 1
26 40561 Ash Plug 1
27 891777 Pedestal Wrapper
2000 1
891788 2500 1
28 891778 Pedestal Bottom
2000 1
891521 2500, 1
29 891523 Pedestal Back 1
30 891527 Ash Pan 1
31 891137 Handle 1
32 40496 Corner Trim 2
33 83466 8-32 x 1/4 Self Tapping Screw 8
34 891524 Front Pedestal Trim 1
35 891779 Right Side Pedestal Trim
2000 1
891526 2500 1
36 891780 Left Side Pedestal Trim
2000 1
891525 2500 1
N/S
u
891944 Trim, One Piece 2000 1
891945 Trim, One Piece 2500 1
37 69354 B36 Blower Assembly 1
N/S = Not Shown
u = Used on heaters manufactured in 2011
All components common except where noted.
Key Part No. Description Model Qty.Key Part No. Description Model Qty.
Key Part No. Description Model Qty.Key Part No. Description Model Qty.
For Models with Legs
Key Part No. Description Qty.
Z40566 Leg, Cast Iron 2
N/S 83339 Bolt, 1/4-20 x 3/4 8

22 Ussc
NOTES

Ussc 23
NOTES

24 Ussc
THISMANUALWILLHELPYOUOBTAINEFFICIENT,DEPENDABLESERVICE
FROMYOURHEATER,ANDENABLEYOUTOORDERREPAIRPARTSCOR-
RECTLY.
KEEPTHISMANUALINASAFEPLACEFORFUTUREREFERENCE.
WHENWRITING,ALWAYSGIVETHEFULLMODELNUMBERWHICHISON
THENAMEPLATEATTACHEDTOTHEHEATER.
WHENORDERINGREPAIRPARTS,ALWAYSGIVETHEFOLLOWINGINFOR-
MATIONASSHOWNINTHISLIST:
1.THEPARTNUMBER
2.THEPARTDESCRIPTION
3.THEMODELNUMBER: _______________________
4.THESERIALNUMBER: _______________________
HOW TO ORDER REPAIR PARTS
UNITED STATES STOVE COMPANY
227 INDUSTRIAL PARK ROAD
P.O.BOX151
SOUTHPITTSBURG,TN37380
[phone]
WWW.USSTOVE.COM