United States Stove CSSU User manual

CAUTION!
Read All Instructions Care-
fully Before Starting The In-
stallation or Operating This
Stove. DO NOT USE THIS HEATER
IN A MOBILE HOME OR TRAILER
SAVE THIS MANUAL FOR FUTURE REFERENCE
THISMANUALWILLHELPYOUTOOBTAINEFFICIENT,DEPENDABLESERVICEFROMTHEHEATER,ANDENABLE
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
UNITED STATES STOVE COMPANY
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
[phone]
C
O
M
P
A
N
Y
U
N
I
T
E
D
S
T
A
T
E
S
S
T
O
V
E
C
S
S
U
851499
OwnersManualOwnersManual
OwnersManualOwnersManual
OwnersManual
18691869
18691869
1869
Caboose PotbellyCaboose Potbelly
Caboose PotbellyCaboose Potbelly
Caboose Potbelly
NOTE: THIS IS NOT A
U.L. LISTED COAL BURNING STOVE
Keeping America Warm
since 1869

Illustrations
This stove has an oval flue
outlet and uses standard 6"
stovepipe. Ill. 1Ill. 1
Ill. 1Ill. 1
Ill. 1
To attach pipe, simply hand
form the smooth end of the
roundstovepipe intoanoval
shape. Ill. 2Ill. 2
Ill. 2Ill. 2
Ill. 2
Slide the crimped end of the
stove pipe into the oval flue
outlet and secure with metal
screw. Connect balance of
stove pipe into a class A
chimney Ill. 3Ill. 3
Ill. 3Ill. 3
Ill. 3
15"
19.5" 21.6"
36"
FLOOR
PROTECTOR
(SIDE VIEW)
(FRONT VIEW)
STOVE DIMENSIONS
FIGURE 1.
Specifications
Height(Overall)...................................... 36" Material............................................ 100% Cast Iron
Width...................................................... 21.6" Fuel.................................................................... Coal
Depth...................................................... 19.5" NOTE: Bituminous, large nut to small egg or
FireboxCapacity.................................... 40 lbs. Anthracite, large egg to small broken.
FireboxDepth......................................... 10"
FlueSize................................................. 6" BTURating.................................................. 200,000
DoorOpening......................................... 8" x 10" Weight......................................................... 216 lbs.
2

CONGRATULATIONS!
YouhavepurchasedaheaterfromNorthAmerica'soldestmanufacturerofwoodandcoalburningproducts. Our
CaboosePotbellyStoveisreminiscentofthepotbellystovesseeninthetrainstationsandcaboosesofyesteryear.
This high performance potbelly stove is constructed of all cast iron and is designed to burn coal. Its generous
firepotcapacitywithshakergrateallows40lbs.ofcoaltoburnforeighthoursbeforerequiringrefueling. Separate
ash door with slide draft control at bottom creates a "forge effect" that insures proper combustion. Long flared
top with 8" lift out lid facilitates fry pan or tea kettle. Stove comes assembled except for legs.
Safety Rules
SAFETY NOTICE: If this heater is not properly installed a house fire may result. For your safety, follow the
installation directions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Read these rules and the instructions carefully.
1. The installation of this stove must comply with your local building code rulings. Please observe the clearances to
combustibles. (Refer to Figures 2 and 3) Stove must be 36" from a combustible wall (wood or plaster board) at
rear or sides.
2. DO NOT install this stove in a mobile home or trailer.
3. Always connect the stove to a chimney and vent to the outside. Never vent to another room or inside a building.
4. DO NOT connect a wood burning to an aluminum Type B gas vent. This is not safe and prohibited by the NFPA
(National Fire Protection Agency) This stove requires approved masonry or a UL 103 HT Listed Residential Type
and Building Heating Appliance Chimney. Use a 6" diameter chimney or larger, that is high enough to give a good
draft.
5. Be sure that your chimney is safely constructed and in good repair. Have the chimney inspected by the fire
department or a qualified inspector. Your insurance company may be able to recommend a qualified inspector.
6. Creosote or soot may build up in the chimney connector and chimney and can cause a house/building fire. Inspect
the chimney connector and chimney twice monthly during the heating season and clean as necessary. (See
Chimney Maintenance, page 6)
7. Provide air for proper combustion from outside the house into the room where the stove is located. If the intake is
not in the same room, air must have free access to the room.
8. To prevent injury, do not allow anyone to use this stove who is unfamiliar with the correct operation of the stove.
9. For further information on using your stove safely, obtain a copy of the National Fire Protection Association publica-
tion "Using Coal and Wood Stoves Safely" NFPA No. HS-10-1976. The address of the NFPA is Batterymarch Park,
MA, 02269.
10. Dispose of the ashes in a metal container with a tight fitting lid. Keep the closed container on a non-combustible
floor or on the ground, well away from all combustible materials. Keep the ashes in the closed container until all
cinders have thoroughly cooled. The ashes may be buried in the ground or picked up by a refuse collector.
11. The special paints used on this stove may give off some smoke and an odor while they are curing during the first
few fires. Paint discoloration will occur if the stove is overfired.
12. This stove has a painted surface which is durable but it will not stand rough handling or abuse. When installing
yourstove, please handle with care. Clean with soap and warm water when stove is not hot. Do not use any acids or
scouring soap, as the will wear and dull the finish.
13. While the stove is in operation, all persons, young children especially, should be alerted to the hazards from high
surface temperatures and should keep away to avoid burns or clothing ignition. Small children should be carefully
supervised when they are in the same room with the stove.
14. Keep stove area clear and free of all combustible materials such as gasoline and/or other flammable vapors and
liquids 3

1. Uncrate and/or unpack the heater, removing all packing
material, being careful not to dispose of the Parts Bag.
2. Remove the following contents:
A. (4) Legs with nut and bolt package
B. (1) Lid with (1) Lid Lifter
C. (1) Shaker Grate
D. (1) Ash Door with (1) Slide Draft
E. (1) Feed Door
3. Carefully lay the stove on its side, preferably on a soft
surface. Note: Cardboard shipping carton placed flat
works well for this application.
4. Securely attach all four (4) legs to lower chamber using
nut and bolt package.
5. Carefully return stove to upright position and place it in
desired location.
6. Place lid in position on top plate.
7. Position ash door with slide draft on front of lower
chamber.
8. Place shaker grate in lower chamber.
Assembly and Installation MINIMUM CLEARANCE
TO COMBUSTIBLE WALLS
FLOOR
PROTECTOR
(60" MIN.)
HEATER/FLOOR PROTECTOR LOCATION
FIG. 4
Place the heater on solid masonry or solid concrete. When
the heater is used on a combustible floor, use an Underwrit-
ers Listed floor protector. The floor protector must comply
with UL Standards. The base should extend at least 18"
beyond the door side of the heater and should extend under
the flue pipe if it is elbowed towards a wall. (Fig. 4).
1. The stove must have its own flue. Do not connect this
unit to a chimney flue serving other appliances.
2. After observing the clearances to combustibles, locate
your floor protector accordingly and carefully place the
stove in your selected location. Install stove pipe ,
elbows and thimble as necessary, utilizing either a
recently cleaned and inspected masonry chimney or a
UL 103 HT Listed Residential Type and Building Heat
ing Appliance Chimney.
3. If your chimney continues to draft excessively, then use
a Barometric Draft Regulator.
4. Usethree(3)sheetmetalscrewsineachstovepipeand
/orelbowjointtofirmlyholdthestovepipetogether. Use
6" round black/blue stove pipe, not galvanized stove
pipe .
5. Recheck illustrations Fig. 2 through 7 to be sure you
have the proper clearances shown from the stove and
the connector pipe to combustible surfaces. NOTE: If
a wall is only faced with brick or stone, consider it as a
combustible wall.
6. DO NOT install this stove in a mobile home or trailer.
7. If you have too much draft, then install a 6" cast iron
stove pipe damper in the first joint of the stove pipe.
CAUTION!
KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS
AWAY FROM THE HEATER.
FLOOR
PROTECTOR
10-1/4
38"
18"
FIGURE 2 FIGURE 3
42"
36"
39-1/2"
14-1/2"
FLOOR
PROTECTOR
NON-COMBUSTIBLE
CONSTRUCTION IN
ACCORDANCE WITH
NFPA 211
DASHEDLINES
SHOW STRAIGHT
OUT CHIMNEY
CONNECTOR 28"
54"
36"
WRONG
RIGHT WRONG
FIG. 5
4
(48")
(44")
(48")
(51-1/2")
Clearances in () are for Canada ONLY.

NOTE: The chimney connector shall not pass through an
attic, roof space, floor, ceiling, or similar concealed space.
Wherepassagethroughawallorpartitionofcombustible
construction is desired, the installation must conform with
NFPA211.
Operation of the Stove
1. Fully open slide draft on ash door and keep spin damper on
feed door closed.
2. Burn wood or coal only. The wood should be air dried
(seasoned) for at least 6 months after cutting. Build six (6)
small fires upon initial firing. Light wood or coal using paper,
twigs, etc.
3. After the fire has been started and is burning satisfactorily,
close slide draft almost all the way.
4. Open/adjust spin draft on feed door to allow additional air into
thestove(ontopofthefire). Thiswillallowamoreefficientburn
cycle.
5. Never build extremely large fires in this type stove as damage
to the stove or smoking may result.
6. DO NOT touch the stove after firing
7. Never overfire this stove by building excessively hot fires as a
house/building fire may result.
8. Inspectstovepipeevery90days. Replaceimmediatelyifstove
pipe is rusting or leaking smoke into the room.
9. Thisisacast ironstove. Itdoesnothave weldedseams. From
time to time you may have to "tune-up" the stove by refilling
and/or replacing the stove cement or mortar along the seams.
10. If stove begins to glow or turn red, you are overfiring.
1.
2.
3.
4.
5.
6.
7.
Crimpedendofthepipemustbeinstalledawayfromtheheater.
The pipe must be hand formed to an oval shape which should
slideonthecollartop.Thepipeshouldbefirmly attachedtothe
collar top with 3 screws and sealed with furnace cement.
Slope any horizontal pipe upward toward the chimney at least
1/4 " inch for each foot of horizontal run.
You must have at least 18" inches clearance between any
horizontal piping and the ceiling. (Fig. 3)
The pipe cannot extend into the chimney flue.(Fig. 5)
Seal each connector pipe joint with furnace cement. Also seal
the pipe at the chimney.
Use3sheet metalscrewsat eachjointtomakethepipingrigid.
It is recommended that no more than two (2) 90 degree bends
be used in the stove pipe installation as more than two (2) may
decrease the amount of draw and possibly cause smoke
spillage.
FIG. 6
FLUE CONNECTION-NON-COMBUSTIBLE WALL
FLOOR PROTECTOR
PIPE
BAROMETRIC
DRAFT REGULATOR
ELBOW PIPE
COLLAR
THIMBLE
NON-COMBUSTIBLEWALL
Chimney Connection
MASONRY CHIMNEY
ThemasonrychimneymustcomplywithULcodes. Beforeusinganexistingmasonrychimney,cleanthechimneyandinspect
the flue liner to be sure it is safe to use. Make repairs before attaching the heater. See Page 3, Item 5. Look at Fig. 5. The
connector pipe and fittings you will need to connect directly to a masonry chimney are shown. If the connector pipe must
go through a combustible wall before entering the masonry chimney, consult a qualified mason or chimney dealer. The
installation must conform to local fire codes, and NFPA 211. Do not connect this heater into the same chimney flue as the
fireplace or flue from another heater. The chimney used for a heater must not be used to ventilate the cellar or basement.
If there is a cleanout opening at the base of the chimney, close it tightly.
UL LISTED CHIMNEY
Carefully follow chimney manufacturer's instructions. Use only listed type HT per UL 103, 6-in diameter black or blued chimney
connector, minimum 24 gauge steel. If your chimney starts at the ceiling (Fig. 7), you will need enough 6" pipe to reach the ceiling.
The top of the chimney must be at least 3 feet above the roof and be at least 2 feet higher than any point of the roof within 10 feet.
(Fig 7)
RULES FOR CONNECTOR PIPE INSTALLATION
FIG. 7
CHIMNEYCAP MANDATORY
3 FT. MIN.
2 FT. MIN
10 FT.
PIPE REDUCER
11 FT. MINIMUM
PIPE
FLOOR PROTECTOR
BAROMETRIC
DRAFT REGULATOR
5
NON-COMBUSTIBLE
CONSTRUCTIONIN
ACCORDANCEWITH
NFPA211

WARNING!
NEVER STORE FLAMMABLE LIQUIDS,
ESPECIALLY GASOLINE. IN THE
VICINITY OF THE HEATER.
CAUTION!
OVERFIRING THE APPLIANCE MAY
CAUSE A HOUSE FIRE. IF A UNIT OR
CHIMNEY CONNECTOR GLOWS, YOU
ARE OVERFIRING.
CAUTION!
NEVER USE GASOLINE, GASOLINE-TYPE
LANTERN FUEL, KEROSENE, CHARCOAL
LIGHTER FLUID, OR FLAMMABLE
LIQUIDS TO START OR "FRESHEN UP" A
FIRE IN THE HEATER.
CAUTION!
USE COAL ONLY. DO NOT USE
DRIED LUMBER, TREATED WOOD
ARTIFICIAL OR PRESSED LOGS.
WARNING!
NEVER OPERATE THIS HEATER WITH THE
FUEL DOOR OPEN. WARNING!
DO NOT OBSTRUCT THE SPACE BENEATH
THE HEATER
Chimney Maintenance
Thechimney connectorand chimneyshould beinspected at
least twice monthly during the heating season to determine
if a creosote or soot buildup has occurred.
Ifthere is anyaccumulation, itshould be removed.Failure to
remove creosote may cause a house fire. Soot may be
removed by using a chimney brush or other commonly
available materials.
Chimneyfiresburnveryhot.Ifthechimneyconnectorshould
glow red, immediately call the fire department, then reduce
the fire by closing the inlet air control and pour a large
quantity of coarse salt, baking soda or cool ashes on top of
the fire in the firebox. CAUTION: A chimney fire may cause
ignitionofwallstudsorrafterswhichyouthoughtwereasafe
distance from the chimney. If you have a chimney fire, have
your chimney inspected by a qualified person before using
again.
Service Hints
Donot expectaheater todraw. Itis thechimneythat creates
thedraft.Smokespillageintothehouseorexcessivebuildup
of water or creosote in the chimney are warnings that the
chimney is not functioning properly. Correct problem before
using heater. Possible causes are:
The connector pipe may push into the chimney too far,
stopping the draft. (Fig. 5)
Donot connect two heatersinto the samechimney flue.
The chimney used for a heater must not be used to
ventilate the cellar or basement. If there is a cleanout
opening at the base of the chimney, It must be closed
tightly.
1.
2.
3.
4.
5.
Ifthe chimneyisoperating toocool,water willcondense
in the chimney and run back into the stove. Soot forma-
tion will be rapid and may block the chimney. Operate
the heater at a high enough fire to keep the chimney
warm preventing this condensation.
If the fire burns well but sometimes smokes or burns
slowly,itmaybecaused bythechimneytopbeinglower
thananotherpartofthehouseoranearbytree.Thewind
blowingover a houseor tree, fallson topof the chimney
likewaterover adam,beating downthesmoke.Thetop
of the chimney should be at least 3 feet above the roof
and be at least to 2 feet higher than any point of the roof
within 10 feet (Fig. 7).
NOTE:
FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT
ALREADY INSTALLED.
CAUTION! Do not touch the heater until it has cooled.
6

Model 1869
Repair Parts
* NOT SHOWN
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART NO.
89979
89980
89981
89982
89983
89984
89985
89986
89987
89988
89989
89990
89991
89992
89993
89994
DESCRIPTION
TOP PLATE
UPPER CHAMBER
FEED CHAMBER
BURN CHAMBER
LOWER CHAMBER
BASE
LEGS
ASH DOOR
SLIDE DRAFT
SLIDE DRAFT KNOB
SHAKER GRATE
SPRING HANDLE
FEED DOOR
SPIN DRAFT
COLLAR TOP
COOK LID
QNTY.
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
16
15
1
2
3
4
5
6
11
13
12
14
10
7
9
8
7

HOW TO ORDER REPAIR PARTS
THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM
THE HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY.
KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE
NAMEPLATE ATTACHED TO THE BACK OF THE HEATER.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION AS SHOWN IN THIS LIST:
1. The PART NUMBER
2. The PART DESCRIPTION
3. The MODEL NUMBER: 1869
4. The SERIAL NUMBER:
UNITED STATES STOVE COMPANY
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
[phone]
www.USSTOVE.com