Unitron Johansson UNIVERSE 8600 User manual

User Manual
UNIVERSE
Ref. 8600

UNIVERSE (REF. 8600)
2
No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any
language without permission.
Unitron reserves the right to change the specifications of the hardware and software described in these
manuals at any time.
Unitron cannot be held liable for any damages resulting from the use of this product.
Specifications are subject to change without notice. 09/15
©Unitron - Frankrijklaan 27 - B-8970 Poperinge - Belgium
T+32 57 33 33 63 F+32 57 33 45 24
email [e-mail]
www.johansson.be - www.unitrongroup.com

UNIVERSE (REF. 8600)
3
CONTENTS
1. INTRODUCTION ...............................................................................4
Product description .............................................................................................4
Package contents ...............................................................................................4
Mounting...........................................................................................................4
Typical installation..............................................................................................5
Safety Instructions .............................................................................................7
2. INSTALLATION OF THE HARDWARE.......................................................8
Module overview ................................................................................................8
Connecting the power supply ...............................................................................9
3. CONFIGURATION OF THE MODULE ......................................................10
3.1. Minimal system requirements...................................................................10
3.2. Starting up the module ...........................................................................10
3.2.1. Device Information......................................................................12
3.2.2. Device Configuration ...................................................................12
Login .............................................................................................. 12
Network .......................................................................................... 13
Firmware Update .............................................................................. 13
Reboot ............................................................................................ 13
3.2.3. Input Settings ............................................................................14
LNB / Multiswitch.............................................................................. 14
Single Cable (EN 50494) and (EN 50607) ............................................ 15
DC for Terrestrial Amp. ..................................................................... 15
3.2.4 CAM ...........................................................................................18
3.2.5 Output Settings ...........................................................................19
IP ................................................................................................... 19
RF .................................................................................................. 21
3.3. Import and export settings ......................................................................24
4TECHNICAL SPECIFICATIONS ............................................................25
5CONDITIONS OF WARRANTY .............................................................27

UNIVERSE (REF. 8600)
4
1. INTRODUCTION
Product description
Receives 1 transponder from any DVB source (satellite, terrestrial or cable)
Decrypts the PayTV channels, when a professional CAM is inserted
Puts the demodulated transponder on your private coaxial and IP network
Can work standalone to insert channels in your existing network
More products can be combined to a make a complete headend:
Cascadable inputs and outputs
Remote powering capabilities
Compatible with SD and HD, with MPEG2 and MPEG4
Perfect picture quality thanks to a MER, comparable to premium headend equipment
Plug&Play thanks to a built-in WebGUI
Package contents
1x Universe (ref.8600)
1x Power adaptor (including mounting plate with tie-wrap)
1x Ethernet cable
Mounting
149 mm
Mounting plate

UNIVERSE (REF. 8600)
5
Typical installation
Perfect when your TV installation does not have satellite tuners, but you wish to receive
satellite TV.
Perfect when your TV installation does not support DVB-T2 tuners, but you wish to
receive the newest DVB-T2 signals. See figure 1.
In existing installation where you want to add a few extra channels from different
sources.
New installations, where you can use 1 or multiple Universes to setup a complete
network of TV and radio channels. See figures 2 and 3.
In some countries, the operator does not support CAMs with business-to-business (B2B)
subscriptions. But if that operator allows professional installations, you can use multiple
Universes with business-to-consumer (B2C) subscriptions without driving the costs too
high.
FIGURE 1: DVB-T2 CONVERTED TO DVB-T SIGNALS AND ADDED TO THE DVB-T BROADCAST
75 cap

UNIVERSE (REF. 8600)
6
FIGURE 2: DVB-T AND DVB-S2 CONVERTED TO DVB-T AND IP CHANNELS
FIGURE 3: DVB-S2 CONVERTED TO DVB-T
75 cap
75 cap
75 cap

UNIVERSE (REF. 8600)
7
Safety Instructions
Read these instructions carefully before connecting the unit
To prevent fire, short circuit or shock hazard:
 Do not expose the unit to rain or moisture.
 Install the unit in a dry location without infiltration or condensation of water.
 Do not expose it to dripping or splashing.
 Do not place objects filled with liquids, such as vases, on the apparatus.
 If any liquid should accidentally fall into the cabinet, disconnect the power plug.
To avoid any risk of overheating:
 Install the unit in a well aired location and keep a minimum distance of 15 cm around the
apparatus for sufficient ventilation
 Do not place any items such as newspapers, table-cloths, curtains,
on the unit that might cover the ventilation holes.
 Do not place any naked flame sources, such as lighted candles, on the apparatus
 Do not install the product in a dusty place
 Use the apparatus only in moderate climates (not in tropical climates)
 Respect the minimum and maximum temperature specifications
To avoid any risk of electrical shocks:
 Connect apparatus only to socket with protective earth connection.
 The mains plug shall remain readily operable
 Pull out power plug to make the different connections of cables
 To avoid electrical shock, do not open the housing of adapter.
Maintenance
Only use a dry soft cloth to clean the cabinet.
Do not use solvent
For repairing and servicing refer to qualified personnel.
Dispose according your local authority’s recycling processes

UNIVERSE (REF. 8600)
8
2. INSTALLATION OF THE HARDWARE
Module overview
1. INPUT: DVB-S/S2, DVB-T/T2, DVB-C
2. BYPASS: to insert a network of existing TV channels (should be blocked with a 75DC-
blocked resistor when not used)
3. CAM INTERFACE
4. TV OUT: DVB-T or ISDB-T
5. LOOP-THROUGH: to connect to the next Universe INPUT (should be blocked with a 75
DC-blocked resistor when not used)
6. 15 VDC INPUT + POWER LED
7. RESET BUTTON
8. ETHERNET CONNECTOR: WebGUI + IP OUT
9. TUNER LOCK LED: indicates if the tuner is locked. If the LED is blinking, that means the
WebGUI is connected.
For typical applications, see figure 1, 2 and 3 on page 5 and next.

UNIVERSE (REF. 8600)
9
Connecting the power supply
The Universe works with the supplied adaptor of 15V DC. The power supply can be connected
via the inlet (6) but the Universe can also be powered via the TV OUT (4).
15V DC is also being supplied to the BYPASS (2), which enables 1 power supply to feed more
than 1 unit. Up to 3 Universes can be powered from the same adaptor.

UNIVERSE (REF. 8600)
10
3. CONFIGURATION OF THE MODULE
3.1. Minimal system requirements
The WebGUI is supported by the following web browsers (and newer versions of these
browsers):
Chrome 4
Safari 3.1
Firefox 3.6
Explorer 9
Opera 10.6
When using a different browser, we cannot guarantee a correct functioning of the interface.
3.2. Starting up the module
Connect all cables needed for your installation. (See p.8 Installation of the Hardware.)
For the first set-up it is advised to connect the Ethernet cable (RJ45) directly to your PC
(without using a switch).
After powering the Universe, wait until the power led turns green (this can take about 2
minutes). Once the power led is green, the unit can be accessed through the WebGUI.
The unit uses 192.168.50.50 as the default IP address. Therefore, you will need to set-
up a static IP in your PC that matches the
subnet of the device. For example
192.168.50.25.
Windows 7
Go to start Control Panel Network and
Internet Network and Sharing Center 
Change Adapter Settings.
Right-click on “Local Area Connection”and
then on “Properties”.
Windows 8
Open the windows 8 start screen by pressing
the start button. Type “Control Panel”and
press enter. Then go to “Network and Internet”
“Network and Sharing Center”“Change
Adapter Settings”. Right-click on “Local Area
Connection”and then on “Properties”.
Double click on “Internet Protocol Version 4
(TCP/IPv4)”to enter the IP settings of your
adaptor.