Universal Remote Control MRF-260i User manual

MRF-260i nstallation Manual
Optimizing Narrow Band Reception
with Complete Control Remotes

MRF-260i Installation Manual ©2007-2013 Universal Remote
Control, Inc.
The information in this owner’s manual is copyright protected. No part of
this manual may be copied or reproduced in any form without prior written
consent from Universal Remote Control, Inc.
UNIVERSAL REM TE C NTR L, INC. SHALL N T BE LIABLE F R PER-
ATI NAL, TECHNICAL R EDIT RIAL ERR RS/ MISSI NS MADE IN
THIS MANUAL.
The Home Theater installation on the cover was designed and installed by
Stone-Glidden of King of Prussia and Doylestown, PA.
The information in this owner’s manual may be subject to change without
prior notice.
Complete Control is a registered trademark of Universal Remote Control,
Inc.
All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]

TABLE OFCO TE TS
Introduction 1
Features and Benefits 2
Parts Guide 2
Installation 3
Testing 5
Front Blaster Overload 6
Disabling the Front Blaster - Step by Step via PC 6
Controlling Four Identical Components/Zones 7
Identical Components/Zones - Step by Step via PC 7
Programming For Multiple Equipment Locations 10
Limited Warranty Statement 11
End User Agreement 13
Frequently Asked Questions 14
Specifications 14

Page 1
MRF-260iBASE STATIO
ntroduction
The MRF-260i base station is an “addressable” base station. RF
Addressing gives you the ability to control as many as 60 identical
components throughout a house. To enable better range and reliabili-
ty the MRF-260i is equipped with the Narrow Band RF reception (like
the MRF-350i), so is only compatible with other Narrow Band remotes.
1. MX/TX remote controls send
radio waves in every direction, so
your client enjoys “No More
Pointing” operation!
OTE: The MRF-260i is NLY compatible with Narrow Band remotes:
the current versions of the MX-3000i, MX-900i remote controls. The MRF-
260i is compatible with all MX-900is and MX-3000is. You can identify the
build date of a remote control by looking at the serial number. The first 6
digits indicate the build date. If the serial number appears as 122905
014054, the first 6 digits indicate that the remote was built on December
29, 2005.
2. The MRF-260i’s integrated Narrow
Band RF receiver receives commands
from any Narrow Band remote con-
trol.
3. The MRF-260i’s built-in Front
Blaster sends commands to compo-
nents in the same cabinet space as
the MRF-260i.
4. Self-adhesive “Flashers” affix to the
front panels of your client’s
components (over the built-in R sen-
sor). The Flashers relay commands to
components out of sight of the MRF-
260i’s Front Blaster. The flashers plug
in to the MRF-260i’s rear flasher line
outputs via their 10 foot cables.
Uniquely, the MRF-260i can also
connect to rear panel IR Inputs via its
two adjustable utputs.

Page 2
MRF-260iBASE STATIO
Features and Benefits
Interference Rejection and Extended Range via arrow Band
The MRF-260i receives RF (radio frequency) signals via its integrated
RF receiver and antenna. The MRF-260i displays RF interference via a
bright red Status LED, which flickers when interference is present if the
D is set to 0. Simply relocate the MRF-260i should interference occur.
Two Fixed IR Outputs
The MRF-260i is equipped with two fixed R line outputs with standard
3.5 jacks for standard R emitter/flashers.
Two Variable IR Outputs Match Rear Panel IR Inputs
The MRF-260i is equipped with two adjustable R line outputs. Each
output can be individually matched to rear panel R inputs on any
component that is designed to be operated by a standard R repeater.
The outputs utilize a 3.5mm jack and are compatible with standard R
emitter/flashers as well.
Up To Fifteen Equipment Locations With Identical Components
Each MX/TX remote is “addressable.” They can be programmed to
specifically control components in a particular room by installing an
MRF-260i base station at each location. n operation it’s simple: when
you select a device located in the Den, the MX/TX remote only sends
commands to the Den. When you select a device located in the
Family Room, the MX/TX remote only sends commands to it.
A Single MRF-260i Can Control an Array of Identical Components
or Identical Zones of a Multi Zone Preamp/Matrix Switcher
Each MRF-260i has four “addressable” R Line Outputs. For example,
you can control up to four identical TV’s with one MRF-260i or route
volume commands for a specific zone to a particular zone R input on
a multi-zone preamp. f you have more than four identical compo-
nents or zones, up to 15 additional MRF-260is can be installed to con-
trol them (thus allowing up to 60 identical components or zones in
one house).
Parts Guide
The MRF-260i RF Base Station includes:
1 - MRF-260i Base Station
1 - Mounting Plate for wall mounting
the MRF-260i
4 - Screws for wall mounting
4 - Visible Flashers with 10 foot plug in
cables.
4 - Extra self adhesive pads for
Emitters
12 - Labels for R Line Outputs
1 - Screwdriver for Variable Outputs

Page 3
nstallation
1. Unplug the MRF-260i. Test all R commands and macros line of
sight.
2. Power on all AV components including the TV. Turn on all of the
lights and lower all dimmers to 50%. Power on anything that may
create RF nterference (particularly devices with high speed
microprocessors or hard drives).
3. Check that the address wheel on the rear of the MRF-260i is set
to D#0 (the interference “sniffing” position).
4. Connect the MRF-260i to its DC wall adapter and plug the wall
adapter into a live AC outlet. Place the MRF-260i in a location at
least 3 feet away from satellite receivers, cable boxes, HDTV
tuners, DVRs, PCs or any other device with a high speed micro-
processor (these generate broad band Radio Frequency
nterference -RF ). Of course, you should keep in mind that the
emitter cables are 10’ long.
MRF-260iBASE STATIO
Check that the arrow pointer in the center of the wheel is pointed to 0, the
default “interference sniffing” position. f it is not, use a small flat blade
screwdriver (included) to set the RF D# to 0.
The red POWER LED indi-
cates that the MRF-260i is
powered on.
The red STATUS LED flashes
differently, based on the
Address setting:
F SET TO D#0
The Status LED flashes
when it receives ANY RF
signal, including RF . This
makes D#0 ideal for
“sniffing” out RF .
F SET TO ANY OTHER D#
The Status LED flashes ONLY
when it receives a correctly
addressed RF command.

Page 4
5. Observe the Status LED of the MRF-260i. f it is glowing or flick-
ering you must relocate the MRF-260i to a location where the
LED doesn’t flicker.
f your installation location simply doesn’t offer you any choice
and you are detecting interference everywhere you place the
MRF-260i, you have two last resort options:
a. Remove the MRF-260i’s antenna. This will reduce the
range enormously, but may still be enough for this client.
b. Admit defeat and install the two piece MRF-350i base
station, which can have the RF Antenna module remote-
ly located (even in another part of the house).
7. Once you have found a location that is absolutely free of RF
with everything on, test to see if the range is ade-
quate and that macro reliability is perfect. Start
with the antenna angle set to 45 degrees and posi-
tioned so that the long side of the antenna is fac-
ing the customer’s favorite seating position.
When testing, set both the remote and the MRF-260i to the same
valid RF D#. Keep in mind that zero (0) is not a valid RF D#.
Watch the Status LED on MRF-260i - it should light every time
you press a button on the remote. This confirms that the signal
was received and understood perfectly. f you repeat any button
press multiple times and the Status LED lights correctly every
time, you have no interference and a very reliable installation. f
some of the presses do not light the Status LED, you still have
some RF . Your best strategy is return to step 3 and try to find a
better location for the MRF-260i.
8. Now that the location is fixed, connect each of the emitters to the
appropriate R output and run the cable to the appropriate com-
ponent. Do not attach the emitters to the front panel yet!
Utilize the included preprinted labels to identify which emitter
goes to which component. f you’d like to make your own, the
slots for the labels have been sized at 12mm to enable a Brother
P-Touch 12mm label to fit perfectly.
OTE: TiVo, Replay TV, other DVRs, Satellite Receivers and Cable
Boxes are all extremely sensitive to R overload or saturation. For
this reason, it is recommended that you always connect the R
flashers for these types of component to the Variable R Outputs of
the MRF-260i.
MRF-260iBASE STATIO
45°

MRF-260iBASE STATIO
Page 5
Testing
Test a few commands for each device before fixing the flasher in
place on the front panel of a device.
Since TiVo, Replay TV, Satellite Receivers and Cable Boxes are all
extremely sensitive to R overload or saturation, you should test
them thoroughly. Put up the on screen guide and test the navigation
arrows. Compare operation via RF to the original remote control.
Operation should be identical. RF is not slower. f operation is
inconsistent or sluggish, lower the R line output and/or reposition
the flasher.
f you still have sluggish operation, check that the remote control is
set to a particular L NE OUT, rather than ALL. When R commands
are sent to all the flashers in a cabinet, you can have difficulty
adjusting the R Output. Reprogram the remote control to send R
commands only via a specific (1-4) Line Output, then readjust the
R Line Output level.
ote: Remember, the MRF-260i will N T respond if you select IR
line outputs 5 or 6. The MRF-260i has only four IR Line utputs.
1. Connect an R emitter to each R output and run the emitter
wire to the front panel of each component. DO NOT ST CK the
emitter in place. ADJUST the level first.
2. Adjust each of the R Output levels for best operation. f the
component operates best at minimum level, but is still operating
sluggishly or intermittently, move the emitter farther away from
the components R sensor.

MRF-260iBASE STATIO
Page 6
Front Blaster Overload
A few models of audio/video components can be overloaded by the
Front Blaster. f you are having intermittent or inconsistent results
with a particular component, try repositioning the MRF-260i and
facing the Front Blaster in a different direction. f this improves the
situation but is impractical, it may be necessary to utilize the self-
adhesive flashers only and follow the steps below to Disable the
Front Blaster. This will limit the number of components your MRF-
260i can control to four. f you have more than four components
you can purchase an additional MRF-260i or upgrade to an MRF-
350i.
Disabling the Front Blaster - Step by Step via PC
Note: If you are programming a URC MX “addressable” remote
control that sets up without a PC, refer to the owners manual to dis-
able the Front Blaster.
Open the PC software, then plug the MX PC programmable remote
control into the PC. Open your saved configuration and follow these
steps to turn off the front blaster:
Step 1 - Open the RF Setup Window
The RF Setup window opens after selecting RF Control or Settings
from the Program Menu of most MX/TX editors or from the Main
Menu of the ProWizard.
Step 2 - Setup the Receiver
Extend the RF Setup window by clicking on the
RECE VERS button.
Step 3 - Turn off the Front
Blaster
Click on the cell in the R
LED OUTPUT/ R BLASTER
column. A list box will
appear. Select OFF from
the list.
ext, click on Close to apply your change.

MRF-260iBASE STATIO
Page 7
Controlling Four dentical Components/Zones
There are several considerations to take into account when you are
installing an MRF-260i to control an array of identical components:
1. The RF D# cannot be set to Code 0, the universal setting. You
must use one of the fifteen unique R Routing addresses.
2. Each identical component must receive R commands ONLY
from a dedicated Flasher affixed to its front panel or a rear panel
direct R input. The S GNAL of the remote should be set to RF
ONLY for each identical component. R can still be utilized for
other devices in your system!
3. You must note the NUMBER of the Flasher Output you have uti-
lized for EACH of the identical components.
dentical Components/Zones - Step by Step via PC
Step 1 - Create and Program a Device for Each Component/Zone
Try to name each device with a descriptive title. At a minimum,
label them TV1, TV2, TV3 and so on.
Step 2 - Open the RF Setup Window
The RF Setup window opens after selecting RF Control from the
Program Menu or from the ProWizard’s Main Menu. The RF Setup
window is composed of a “spread sheet” of options for EACH of
your devices.
By looking at the Signal column, you can see that the factory

MRF-260iBASE STATIO
Page 8
default programming sets all of the devices to send both R and RF
commands. f you look at the column for Flashers, you can see that
the default sends R commands for all devices to ALL of the flash-
ers. Both options must be changed for identical components.
Additionally, you must disable the Front Blaster (see page 6 for
directions).
Step 3 - Adjust the Signal For Each of the Identical Devices
The RF Setup window enables you to adjust the Signal output for
each device individually, by clicking on the intersection of a row
and a column and then selecting RF from the three options shown
in the pull down list box.
Select RF from the three options shown for EACH of the identical
TVs. You may leave the other components of the system set to IR
& RF.
Step 4 - Adjust the Flashers For Each of the Identical Devices
The RF Setup window enables you to adjust which Flashers output
by the remote control for each device individually, by clicking on
the intersection of a row and a column and then selecting 1-4 from
the seven options shown in the pull down list box.
Select the correct Flasher (refer to your connection notes) for
EACH of the identical TVs. You may leave the other components of
the system set to ALL.
See figure on the next page.
n the figure below, each device is set to a specific flasher.

Page 9
MRF-260iB
ASE STATIO
ote: Remember, the MRF-260i will only respond to selections 1
through 4.
Step 5 - Make sure that the ID# is set on both the remote and on
the wheel of the MRF-260i.
Click on the Receivers button and set the RF address to one of the
first 15 addresses (1-9 or A, B, C, D or E). The second set of address-
es is only supported by MSC units.
Step 6 - Close the RF window and Download to the Remote.

MRF-260iBASE STATIO
Page 10
Programming For Multiple Equipment Locations
You can operate up to 15 different equipment locations, each with
an MRF-260i assigned a unique Receiver D#. You program each of
your remotes to talk to the equipment locations you want by assign-
ing each of your devices to a receiver. First, you must add and
name your receivers for the locations they are placed in:
Step 1 - Open the RF Setup Window
The RF Setup window opens after selecting RF Control from the
Program Menu or RF Settings from the Main Menu of ProWizard.
Step 2 - Reveal the Receiver settings
Extend the RF Setup window by clicking on the Receivers button of
the RF setup window.
Step 3 - Add, ame and Assign Receiver ID#
Using the controls at the bottom extended portion of the RF Control
window, add new receivers and rename them for the equipment
location.
Step 4 - Save and Download to your
remote.
You may rename the Default
receiver to something more
descriptive by clicking on
the Rename button.
Add new receivers by click-
ing on the Add button.
Delete receivers by selecting them
first by clicking on their Name,
then clicking the Delete button.
Assign the correct Receiver D# for
each LOCAT ON by clicking on the
desired CELL and selecting the D#
you want from the pull down list.
Each LOCAT ON should have a
unique D#. t is ok to install multi-
ple MRF-260i’s in one location.

MRF-260iBASE STATIO
Page 11
Limited Warranty Statement
1. LIMITED WARRA TY A D DISCLAIMERS
Universal Remote Control, nc. (“URC”) warrants that URC
equipment purchased directly from URC or from an authorized
URC dealer or distributor shall be free from defects in material and
workmanship under normal usage for a period of one (1) year from
the date of purchase of the product by the end-user, but no longer
than thirty-six (36) months from the date of shipment of the URC
equipment by URC to an authorized URC dealer or distributor,
except that with respect to Total Control® whole-house products,
the warranty extends for two (2) years from the date of purchase by
the end-user, but no longer than forty-eight (48) months from the
date of shipment of the URC equipment by URC to an authorized
URC dealer or distributor.
This limited warranty is valid only in the United States of America.
URC equipment purchased from other than an authorized URC
dealer or distributor is without warranty.
URC warrants that the software will substantially conform in any
material respect to its functional specifications at the time of
delivery. URC SHALL NOT BE L ABLE FOR OPERAT ONAL,
TECHN CAL OR ED TOR AL ERRORS AND/OR OM SS ONS
MADE N THE URC DOCUMENTAT ON. URC DOES NOT
WARRANT THAT THE URC SOFTWARE S BUG-FREE OR ERROR
FREE OR THAT THERE ARE NO ERRORS/BUGS N THE URC
SOFTWARE.
URC warrants that at the time of purchase the URC equipment and
the URC software complied with all applicable regulations and
policies of the Federal Communications Commission ("FCC")
regarding electromagnetic interference caused by
electronic/computing devices and to the extent that the URC
equipment and/or the URC software fails to so comply, URC shall,
at its own expense, take all reasonable measures to promptly cause
such to comply.
TH S L M TED WARRANTY DOES NOT COVER TECHN CAL
ASS STANCE FOR HARDWARE OR SOFTWARE USAGE EXCEPT
AS EXPRESSLY PROV DED FOR HERE N.
CERTA N MPL ED WARRANT ES, NCLUD NG AN MPL ED
WARRANTY OF MERCHANTAB L TY AND F TNESS FOR A
PART CULAR PURPOSE, MAY BE AVA LABLE W TH RESPECT TO
URC EQU PMENT. MPL ED WARRANT ES VARY FROM STATE
TO STATE. URC EXPRESSLY L M TS THESE MPL ED
WARRANT ES, TO THE EXTENT ALLOWABLE BY LAW, TO THE
T ME PER ODS COVERED BY THE EXPRESS WR TTEN
WARRANT ES PROV DED HERE N. OTHERW SE AND EXCEPT AS
PROV DED FOR HERE N, URC EXPRESSLY D SCLA MS ALL
WARRANT ES, EXPRESS, STATUTORY OR MPL ED, AND MAKES
NO REPRESENTAT ONS REGARD NG THE USE OF, OR THE
RESULTS OF THE USE OF, THE EQU PMENT, SOFTWARE OR
DOCUMENTAT ON N TERMS OF CORRECTNESS, ACCURACY,
REL AB L TY OR OTHERW SE.

MRF-260iBASE STATIO
Page 12
EXCEPT AS EXPRESSLY PROV DED FOR HERE N, TECHN CAL
SERV CES ARE SUPPL ED "AS S", W THOUT ANY WARRANTY,
EXPRESS, STATUTORY OR MPL ED, OF ANY K ND. TO THE
MAX MUM EXTENT PERM TTED BY APPL CABLE LAW, URC
EXPRESSLY D SCLA MS ALL WARRANT ES RELAT NG TO
TECHN CAL SERV CES, EXPRESS, STATUTORY OR MPL ED,
NCLUD NG BUT NOT L M TED TO THE WARRANT ES OF
QUAL TY OR REASONABLE SK LL AND CARE, OR OUTCOME
OR RESULTS.
W THOUT N ANY WAY L M T NG THE GENERAL TY OF THE
OTHER PROV S ONS HERE N, TH S L M TED WARRANTY DOES
NOT COVER: ( ) DAMAGE FROM M SUSE, NEGLECT OR ACTS
OF NATURE, ( ) MOD F CAT ONS, ( ) NTEGRAT ON W TH
TH RD PARTY CONTENT, OR ( V) BEYOND THE WARRANTY
PER OD AND/ OR FA LURE TO FOLLOW URC WARRANTY
CLA M PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to
end user in whole or in part, where such are restricted or excluded
by applicable law, and such shall apply to the maximum extent
permitted by applicable law.
n the event of any warranty claim, URC will, at its sole option,
repair the URC equipment using new or comparable rebuilt parts,
or exchange the URC equipment for new or rebuilt equipment. In
the event of a defect, these are the end user's exclusive remedies.
All the URC equipment returned for service, exchange or repair
require an RGA number. To obtain an RGA number, you must
complete a Return Request Form which you may obtain by calling
[phone] or contacting URC at
[email protected]. To obtain warranty service,
end user must deliver the URC equipment, freight prepaid, in its
original packaging or packaging affording adequate protection to
URC at 420 Columbus Avenue, Valhalla, NY 10595. t is end user's
responsibility to backup any macro programming, artwork, software
or other materials that may have been programmed into the unit. t
is likely that such data, software, or other materials will be lost
during service and URC will not be responsible for any such
damage or loss. A dated purchase receipt, bill of sale, installation
contract or other verifiable proof of purchase is required. For the
URC equipment support and other important information, please
visit URC's website available at www.universalremote.com or call
the Customer Service Center at [phone].
This limited warranty only covers the URC equipment issues
caused by defects in material or workmanship during ordinary
consumer use. t does not cover product issues caused by any other
reason, including but not limited to product issues due to
commercial use, acts of God, third-party installation, misuse,
limitations of technology, or modification of or to any part of the
URC equipment. This limited warranty does not cover the URC
equipment sold as used, as is, refurbished, so called "B stock" or
consumables (such as batteries). This limited warranty is invalid if
the factory applied serial number has been altered or removed from
the URC equipment. This limited warranty specifically excludes
the URC equipment sold by unauthorized resellers.

MRF-260iBASE STATIO
Page 13
With the exception of URC's R-only, broad-based consumer
remotes, none of URC's PC programmable remotes or any of our
Total Control® whole-house equipment are authorized for online
internet sales. Buying URC's PC programmable remotes or any of
our Total Control® whole-house equipment online means buying
equipment that does not have URC's limited warranty. Such
equipment is not eligible for URC tech support or software support,
either.
2. URC'S LIMITATIO S OF LIABILITY
N NO EVENT SHALL URC BE L ABLE FOR ND RECT, SPEC AL,
NC DENTAL, EXEMPLARY, PUN T VE OR CONSEQUENT AL
DAMAGES OF ANY K ND OR LOSS OF PROF TS OR BUS NESS
OPPORTUN TY, EVEN F URC S ADV SED OF THE POSS B L TY
OF SUCH DAMAGES.
N NO EVENT SHALL URC BE L ABLE FOR LOSS OF OR
DAMAGE TO DATA, COMPUTER SYSTEMS OR COMPUTER
PROGRAMS.
URC'S L AB L TY, F ANY, FOR D RECT DAMAGES OF ANY
FORM SHALL BE L M TED TO ACTUAL DAMAGES, NOT N
EXCESS OF AMOUNTS PA D BY END USER FOR THE URC
EQU PMENT.
N NO EVENT SHALL URC BE L ABLE FOR ANY EVENTS
BEYOND TS CONTROL, NCLUD NG ANY NSTANCE OF
FORCE MAJEURE.
N NO EVENT SHALL URC BE L ABLE FOR THE ACTS OR
OM SS ONS OF END USER OR ANY TH RD PARTY.
THE L M TAT ONS OF L AB L TY MAY NOT APPLY TO END USER
N WHOLE OR N PART, WHERE SUCH ARE RESTR CTED
L M TED OR EXCLUDED BY APPL CABLE LAW AND SUCH
SHALL APPLY TO THE MAX MUM EXTENT PERM TTED BY
APPL CABLE LAW.
URC SHALL NOT BE HELD RESPONS BLE FOR THE STATEMENTS
MADE BY OTHERS.
SOME STATES OR JUR SD CT ONS DO NOT ALLOW THE
EXCLUS ON OR L M TAT ON OF NC DENTAL OR
CONSEQUENT AL DAMAGES, OR ALLOW L M TAT ONS ON
HOW LONG AN MPL ED WARRANTY LASTS, SO THE ABOVE
L M TAT ONS OR EXCLUS ONS MAY NOT APPLY TO END USER.
TH S L M TED WARRANTY G VES END USER SPEC F C LEGAL
R GHTS AND END USER MAY HAVE OTHER R GHTS WH CH
VARY FROM STATE TO STATE OR JUR SD CT ON TO
JUR SD CT ON.
End User Agreement
The terms and conditions of the End User Agreement available at
www.universalremote.com/eua.php shall apply.

MRF-260iBASE STATIO
Page 14
Frequently Asked Questions
Can I use flasher/emitters that I have already installed in the sys-
tem to connect to the MRF-260i?
Yes, the flashers are compatible if they use 3.5mm mono mini plugs with
the same polarity (Tip is data, sleeve is ground).
I’m getting inconsistent operation regardless of flasher level or
position.
Some components are easily overloaded with R from nearby flashers.
Prevent R from affecting the problem component from other flashers or the
front panel blaster by setting the device to a specific R Line Output instead
of ALL, then adjust the Line Output.
I have a row of identical TVs. I’ve correctly set the flasher outputs
using the Editor software, yet when I send a command to one of
them, the TV next to the selected TV also responds. How do I stop
this?
First, check the RF D#, if the RF D# is set to 0, R routing does not work.
Second, set the RF D# from 1-9 or A-F on both the remote control and the
rear of the MRF-260i. Third, check that the flasher level is set to the mini-
mum necessary. Fourth, check that the emitter is facing the component.
Specifications
Power Supply: 9V 300mA
R Flasher Line Outputs: 3.5mm Mono Mini Jack
RF Frequency: 433.92MHz

500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]
www.universalremote.com
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interfer-
ence to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. f this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one
more of the following measures:
Reorient or relocate the receiving antenna.
ncrease the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications not expressly approved by the manu-
facturer could void the user's authority to operate the equip-
ment.
Note : The manufacturer is not responsible for any Radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's authority
to operate the equipment.
" User shall attention to the external ac adpater to be used before connection
to the MRF-260i Base station. Only LPS satisfied external AC adapter shall
be used and connected for safety operation of base station "
nformation To The User
OCE-0057B Rev04_RH