Universal Remote TRF-ZW1 User manual

TRF-ZW1 Z-Wave Extender
Owner’s Manual

500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]
RF-ZW1 Z-Wave Extender Owner's Manual
© 2013 Universal Remote Control, Inc.
he information in this Owner’s Manual is copyright protected. No part of this manual
may be copied or reproduced in any form without prior written consent from Universal
Remote Control, Inc.
UNIVERSAL REMO E CON ROL, INC. SHALL NO BE LIABLE FOR OPERA IONAL,
ECHNICAL OR EDI ORIAL ERRORS/OMISSIONS MADE IN HIS MANUAL.
he information in this Owner’s Manual may be subject to change without prior notice.
URC - Control the Experience is a registered trademark of Universal Remote Control, Inc.
otal Control is a registered trademark of Universal Remote Control, Inc.
All other brand or product names are trademarks or registered trademarks of their
respective companies or organizations.

TRF-ZW1 EXTENDER
Congratulations!
Thank you for purchasing URC’
s TRF-ZW1 Z-Wave Extender for the T
otal
Control system. The Z-Wave Extender receives commands from a T
otal
Control system and sends those commands over the Z-Wave network to
third-party products such as door locks, lights etc. Some compatible
third-party products are capable of sending metadata back to a T
otal
Control user interface when using URC’
s two-way modules.
Features and Benefits
● Control Z-Wave products with your
T
otal Control system
Y
our T
otal Control system receives commands, converts them to
Z-Wave signals and then transmits the signals to your products. Also,
while at home or away
, control your Z-Wave products using URC’
s
mobile apps from your mobile devices.
●Monitor compatible Z-Wave products
While using applicable URC two-way modules, monitor Z-Wave
products with metadata feedback on a T
otal Control remote, keypad,
or mobile device.
●Pairing just got easier
The included batteries allow for roaming and easier pairing of
hard-to-reach Z-Wave products installed throughout the home.
●Remote Device Management & Configuration
Access the TRF-ZW1’
s user interface via its online site whether you
are at home or away
. Register a free account for basic control and
Z-Wave configurations from home, or subscribe to a yearly account
to access the TRF-ZW1 from anywhere else.
Parts Guide
The TRF-ZW1 Extender includes:
1 - TRF-ZW1 Extender 1 - Ethernet Cable
1 - Power Adaptor 4 - AA Batteries
1 - Owner’
s Manual
1

2
TRF-ZW1 EXTENDER
TRF-ZW1 Top Panel Descriptions
Power LED: lluminates to indicate the TRF-ZW1 is powered.
Ready: lluminates to indicate it is ready to receive data.
Network: lluminates to indicate communication to the home network.
Error: Please consult the troubleshooting section of the URC M OS
documentation site. http://urc-docs.mios.com/doc.php
Battery button: This button is used to enter battery pairing mode
while pairing devices in various locations.
1. Disconnect the TRF-ZW1 from the network and power cable.
2. nsert 4 AA batteries into the bottom of the unit.
3. Press and Hold the “Battery” icon on the top of the unit for 5 seconds.
●The Power light will start to flash Blue for 30 seconds.
●After 10 more seconds the ready light will start to flash amber. By
default the unit goes into Pairing ( nclude) mode automatically.
+ (pairing button): Stated above the TRF-ZW1 defaults to Pairing
( nclude) when battery power is activated.
1. The Ready light will slowly flash to show it is ready to pair a device.
2. Go to the device you wish to pair and perform its instructed
pairing method.
3. The ready light will quickly start flashing for 2 seconds to verify
the device has been paired.
4. You can continue to pair devices while in pairing mode.
5. When you are done pairing (including) devices press the [+]
button to save.
●The Ready light will not flash for a moment while saving.
6. To turn off Battery mode press and hold the [+] button for 5 seconds.

3
7. Connect the TRF-ZW1 back to the network and power cables
then login to the TRF-ZW1 programming software. You will find
the items add to the “No Rooms” section.
– (un-pairing button): After the TRF-ZW1’s battery mode is
activated and the ready light is flashing for pairing (include) you
will press the [-] on the unit. When the [-] button is pressed the
ready light will flash slightly faster in un-pairing (exclude) mode,
then in pairing (include) mode).
1. Go to the device you wish to un-pair (exclude) from the system
and perform the devices instructed in the un-pairing method.
2. The Ready light will quickly flash for 2 seconds to verify the
item has been un-paired (excluded).
3. When you are done un-pairing devices press the [-] to save the
changes.
● The Ready light will pause from flashing for a moment to
confirm.
4. To turn off battery mode press and hold the [+] for 5 seconds.
5. Connect the TRF-ZW1 back to the network and power cables
then login to the TRF-ZW1 programming software. You will find
the items removed are no longer in the program.
Reset button: WARN NG!!! Pressing this button will set the unit
back to factory settings. Press and hold the recessed button adjacent
to the (-) unpair button for 10 seconds until the lights turn off.
TRF-ZW1 EXTENDER

4
TRF-ZW1 EXTENDER
TRF-ZW1 Rear Panel Descriptions
USB: For future use.
Network: Connect the supplied Ethernet cable to the home
network.
Power: 12V power receptacle.

5
TRF-ZW1 EXTENDER
Installation
 Connect the supplied Ethernet cable to the TRF-ZW1’s
network port and to an open connection port on your router
or network switch.
 Connect the 12V power adapter to the TRF-ZW1’s power port
and plug into an electrical outlet.
 The LED indicators, Power, Ready and Network illuminate
when powered. Wait for the LEDs to remain lit; this may take
up to 2 minutes. When the lights are solid, the TRF-ZW1 is
properly connected to the network.
Open a browser and type in https://urc.mios.com.
 Create an account for access to the TRF-ZW1 Dashboard. The
online interface will discover the TRF-ZW1 and open its
Dashboard. Refer to the TRF-ZW1 Dashboard and Account
Setup section for further details.

6
TRF-ZW1 EXTENDER
TRF-ZW1 Dashboard and Account Setup
The TRF-ZW1 Dashboard is a user-friendly interface used to pair
and configure Z-Wave devices to the TRF-ZW1. t is also used for
advanced configuration settings and device control throughout
your home or office space. Creating an account and setting up
your devices via the Dashboard is REQU RED to enable the
TRF-ZW1 to work in conjunction with your Total Control system.
The Dashboard is accessible by logging into https://urc.mios.com
and offers two different accounts: free and yearly subscription.
Free account: Connecting to the TRF-ZW1 allows for advanced
device configuration from the local network via a PC at no
additional charge. This account option allows you to:
• Add devices
• Configuration of devices
• Edit scenes
• View scenes
• View dashboard
• Basic control
early Subscription: Signing up for a TRF-ZW1 Dashboard
account with a yearly subscription provides access to your
TRF-ZW1’s advanced configuration settings and device control
from a remote location via the internet. No matter where you are,
such as your office or on vacation, you can monitor and open a
door and allow access to your home. This account option provides:
• Off-site access (outside local area network)
• Off-site control via dashboard
• Device configuration
• Adding and deleting a device
• Managing scenes
• Adding multiple users
• Email and SMS notifications
Note: he account offerings are subject to change.

7
TRF-ZW1 EXTENDER
Visit https://urc.mios.com/ to register for an account and
view the RF-ZW1’s Dashboard.
For instructions on how to use the dashboard, please refer to,
http://urc-docs.mios.com/doc.php

8
TRF-ZW1 EXTENDER
Limited Warranty Statement
1. Limited Warranty and Disclaimers
Universal Remote Control, nc. (“URC”) warrants that the URC equipment
shall be free from defects in material and workmanship under normal
usage for one (1) year from purchase when such is purchased from URC.
This limited warranty is valid only in the United States of America. URC
warrants that the software will substantially conform in any material respect
to its functional specifications at the time of delivery. URC SHALL NOT BE
L ABLE FOR OPERAT ONAL, TECHN CAL OR ED TOR AL ERRORS
AND/OR OM SS ONS MADE N THE URC DOCUMENTAT ON. URC
DOES NOT WARRANT THAT THE URC SOFTWARE S BUG-FREE OR
ERROR FREE OR THAT THERE ARE NO ERRORS/BUGS N THE URC
SOFTWARE.
URC warrants that at the time of purchase the URC equipment and the
URC software complied with all applicable regulations and policies of the
Federal Communications Commissions (“FCC”) regarding electromagnetic
interference caused by electronic/computing devices and to the extent that
the URC equipment and/or the URC software fails to so comply, URC
shall, at its own expense, take all reasonable measures to promptly cause
such to comply.
URC equipment purchases from other than an authorized URC dealer or
distributor are without warranty.
TH S L M TED WARRANT DOES NOT COVER TECHN CAL ASS STANCE
FOR HARDWARE OR SOFTWARE USAGE EXCEPT AS EXPRESSLY
PROV DED FOR HERE N, THE EQU PMENT, SOFTWARE AND
DOCUMENTAT ON OF URC ARE SUPPL ED “AS S” W THOUT ANY
WARRANTY, EXPRESS, STATUTORY OR MPL ED, OF ANY K ND. TO
THE MAX MUM EXTENT PERM TTED BY APPL CABLE LAW, URC
EXPRESSLY D SCLA MS ALL WARRANT ES, EXPRESS, STATUTORY OR
MPL ED, NCLUD NG BUT NOT L M TED TO THE WARRANT ES OF
MERCHANTAB L TY AND F TNESS FOR A PART CULAR PURPOSE.
URC DOES NOT WARRANT, GUARANTEE, OR MAKE ANY
REPRESENTAT ONS REGARD NG THE USE OF, OR THE RESULTS OF
THE USE OF, THE EQU PMENT, SOFTWARE OR DOCUMENTAT ON N
TERMS OF CORRECTNESS, ACCURACY, REL AB L TY OR OTHERW SE.