Universal Tool UT8706-2 Datasheet

Universal Tool
™
MODEL: UT8706-2
1/8" Pencil Grinder
54,000 RPM

Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free.
Higher pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air
line will cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can
be viewed in the illustration below. The air inlet, used for connecting air supply, has standard 3/8”NPT American Thread. Line pressure should be increased to
compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 1/2”I.D. and ttings should have the same inside dimensions.
Safety Information (continued)
AIR COMPRESSOR AND AIR TOOL SAFETY
1. Risk of Bursting. Do not adjust the regulator to result in output
pressure greater than the marked maximum pressure of this air
tool.
2. Ensure the hose is free of obstructions or snags. Entangled or
snarled hoses can cause loss of balance or footing and may
become damaged.
3. Never leave a tool unattended with the air hose attached.
4. Do not operate this tool if it does not contain a legible warning
label.
5. Do not continue to use a tool or hose that leaks air or does not
function properly.
6. Never direct a jet of compressed air toward people or animals.
7. Protect your lungs. Wear a face or dust mask if the operation is
dusty.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
Lead from lead based paint, crystalline silica from bricks
and cement and other masonry products, arsenic and
chromium from chemically-treated lumber.
Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well-ventilated area, and work
with approved safety equipment, such as dust masks that
Recommended Air Pressure of 90 psi - 6.2 bar
AIR TOOL SETUP
Model # Motor
(hp)
Motor
Kw)
Max. Capacity
(in)
Speed
(rpm)
Exhaust Collet
Size
Weight
(lb)
Weight
(kg)
Length
(in)
Length
(mm)
Air Inlet
(npt/bsp)
Rec. Hose
(id. In)
Air Cons.
(cfm)
Avg. Air
Cons. (cfm)
UT8706-2 0.25 0.18 1/8 54,000 Rear 1/8" 0.50 0.20 5.25 133 1/4" NPT/BSP 1/4 16 4.00
Recommended Air Pressure of 90 psi - 6.2 bar

MODEL: UT8706-2
1/8" Pencil Grinder
54,000 RPM
Exploded View & Parts List
Universal Tool
™
Ref # Part # Description Qty Ref # Part # Description Qty
1 9700001 REAR END HOLDER 1 17 9560016 LATERAL DISC 1
2 9560002 SCREW 1 18 9560017 BALL BEARING 1
3 9560004 O-RING 1 19 9700019 INTERIOR BEARING RETAINER BUSHING 1
4 9700004 SLIDING KNOB 1 20 9700020 OUTER BEARING RETAINER BUSHING 1
5 9560005 O-RING 1 21 9700021 COLLET FOUNDATION 1
6 9560007 HOSE PLUG 1 22 9700022 SLEEVE 1
7 9560006 PIN 1 23 9700023 FRONT COVER 1
8 9700008 PLUG 1 24 9560021 COLLET 1
9 9560008 INTAKE PLATE 1 25 9700025 CLAMPING NUT 1
10 9560009 BALL BEARING 1 26 9560026 MUFFER TUBE 1
11 9560011 BEARING PLATE 1 27 9560027 HOSE RING 1
12 9560010 PIN 1 28 9560028 AIR HOSE 1
13 9560014 CYLINDER 1 29 9560029-11 INLET CONNECTOR FOR NPT 1
14 9560013 ROTOR BLADE 3 9560029-13 INLET CONNECTOR FOR BSP 1
15 9700015 ROTOR 1 30 9560030 SPANNER 2
16 9560015 SPACER 1

Warranty
Limited Warranty: Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
Tool or its authorized service centers. If a UT tool proves defective in material or workmanship within one year after purchase, return
it to any authorized service center or Universal Tool freight prepaid. Please enclose your name, address and adequate proof of date of
purchase and a short description of the defect. Universal Tool will,at its option, repair or replace defective tools free of charge. Repairs or
replacements are warranted as described above for the remainder of the original warranty period. Universal Tool's sole liability and your
exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential or special damages,
or any other damages,costs or expenses excepting only the cost or expense of repair or replacement as described above.
Unit 8 Lane End Industrial Park
High Wycombe
Bucks HP14 3BY
United Kingdom
Tel: [phone]
Fax: [phone]
Email: [email protected]
Email: [email protected]
www.universal.co.uk
Headquarters
851 Jupiter Park Lane - Unit A
Jupiter FL 33458
USA
Tel: [phone]
Fax: [phone]
orders@orida-pneumatic.com
www.universaltoolusa.com
Universal Tool a Division of
Florida Pneumatic Manufacturing Corporation
Universal Tool
™