Universal Tool UT8719 User manual

PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before operating
any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection should
meet or exceed the standards as set forth
in the United States ANSI Z87.1,
Occupational and Educational Eye and
Face Protection. Look for the marking
Z87.1 on your eye protection to insure that
it is an approved style. For further
information, ANSI Z87.1, Occupational and
Educational Eye and Face Protection, is
available from the American National
Standards Institute, Inc., 11 West 42nd
Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used when the
noise level exposure equals or exceeds an
8 hour time-weighted average sound level
of 85 dBA. Process noise, reflective
surfaces, other tools being operated
nearby, all add to the noise level present in
your work area. If you are unable to
determine your noise level exposure, we
recommend the use of hearing protection.
Avoid Prolonged Exposure to
Vibration
PnuematicTools can vibrate during use.
Prolonged exposure to vibration or very
repetitive hand and arm movements, can
cause injury. Stop using any tool if
discomfort, tingling feeling or pain occurs.
You should consult your physician before
resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at an air
pressure of 90 pounds per square inch
gauge pressure (90 PSIG) maximum, at the
tool. Use of higher air pressure can, and
may cause injury. Also, the use of higher
air pressure places the internal components
under loads and stresses they were not
designed for, causing premature
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate or
service this Florida Pneumatic product. Failure to comply with the instruc-
tions could result in personal injury and/or property damage! Retain these
instructions for future reference.
Safety Instructions
The following instructions are furnished as
general guidelines for use of your pneu-
matic tool. They cannot comprehensively
cover all possible or conceivable uses of
the subject tool. For additional information
on the safe use of air tools, we advise you
to obtain a copy of ANSI B186.1 Safety
Code for Portable Air Tools, available from
the following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the following
instructions, indicates that adherence to
the particular requirement is necessary to
conform to ANSI B186.1.
ToolApplication and Usage
Pneumatic tools shall be used only for the
purposes intended in their design and
within the capacity for which they were
intended and rated. It shall be the tool owner’s
and/or employer’s responsibility to instruct
each operator in the safe use of the tool.
Tools shall not be used without guards and
safety devices as furnished by the manufac-
turer. Where an air tool is modified or altered,
the modifier shall provide the safeguards to
enable it to be safely used in the operations
intended and to comply with any applicable
provisions as contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit air
pressure to the rated pressure where the
supply pressure exceeds the tool’s rated
pressure. Air hoses and lines shall be
relieved of compressed air before being
disconnected or disjointed, unless there is
automatic valve closing protection at the joint
being separated. Synthetic lubricants which
can cause deterioration of elastomer seals
shall not be used in air systems of air tools.
TT
TT
ToolMaintenanceoolMaintenance
oolMaintenanceoolMaintenance
oolMaintenance
It shall be the tool owner.s and/or
employer.s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools
shall be disconnected from their
compressed air supply before repairs
are attempted. Repairs shall be
consistent with the manufacturer.s
recommended procedures.
Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner.s and/or
employer.s responsibility to keep
required rating markings and warnings
on the tool in legible condition.
.FPMC
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or reproductive harm. Some examples of
these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks, cement and
other masonry products
•Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-
ventilated area and work with approved safety
equipment such as those dust masks that are
specially designed to filter out microscopic
particles.
MODEL NO. UT8719 / UT8719K
DESCRIPTION
DescriptionDescription
DescriptionDescription
Description
Universal Tool Multi-Angle Belt Sander is designed fro hard-to-reach corners,
contours, and hard-to-finish surfaces. Used to sand, grind, and finish aluminum,
steel, cast iron, plywood, plastic and stone. Please note : Multi-Angle Belt
Sanders are not designed for sanding directly on the front roller.
UT8719 (Shown with Kit)

Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by
someone other than Universal Tool or its authorized service centers. If a Universal Tool proves defective in
material of workmanship within one year after purchase, return it to any authorized service center or to Universal
Tool, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a brief
description of the defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairs
or replacements are warranted as described above for the remainder of the warranty period. Universal Tool's sole
liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential
or special damages, or any other damages, costs or expense of repair or replacement as described above.
Specifications:
MODEL NO. UT8719 / UT8719K
DESCRIPTION
MODEL NO. UT8719 / UT8719K
DESCRIPTION
Ref. # Part NO. Description Qty. Ref. # Part NO. Description Qty.
1 962001-1 HOUSING 1 41 951541-12 SPRING 1
2 96T-620030 SCREW (M4X25L) 1 42 940337 SPRING PIN (3*18L) 1
3 96T-620003 AIR INLET 1 43 96T-620143 PLATEN PAD 2
4 96T-620004 THROTTLE LEVER 1 44 96T-620144 PLUG 1
5 962005-1 VALVE STEM 1 45 96U-620143 PLATEN PAD 2
6 962006-1 VALVE 1 46 96T-620140 DUST COVER 1
7 9000016 O-RING (3.8X1.9) 1 47 96T-620146 SCREW THREAD INSERT
S
1
8 962008-1 SPRING 1 49 96W-620143 PLATEN PAD 2
9 962009-1 O-RING (14.5X1.5) 1 50 96T-620141 CONTACT ARM 1
10 962010-1 SPACER 1 51 96U-620141 CONTACT ARM 1
11 962011-1 RETAINING RING (RTW-18) 1 52 96V-620141 CONTACT ARM 1
12 962012-1 SPACER 1 53 96W-620141 CONTACT ARM 1
13 9619047 CAP SCREW (M5X16) 1 54 96X-620141 CONTACT ARM 1
14 962014-1 REAR END PLATE 1 55 96T-620134-0002S IDLE PULLEY 1
15 96T-620115 ROTOR 1 56 96U-620134-0002S IDLE PULLEY 1
16 962016-1 ROTOR BLADE 4 57 96V-620134-0002S IDLE PULLEY 1
17 96T-620107 SCREW 1 58 96W-620134-0002S IDLE PULLEY 1
18 962018-1 CYLINDER 1 59 96X-620134-0002S IDLE PULLEY 1
19 962019-1 FRONT END PLATE 1 60 970125 PIN 1
20 9051220 BALL BEARING (6000ZZ) 1 61 9PN03001708 PIN 1
21 962021-1 CAP 1 62 9PN03001208 PIN (3X12.8) 2
22 96T-620122 DRIVE WHEEL 1 63 9PN03000708 PIN (3X7.8) 1
23 96T-620123 NUT 1 64 96T-620102 GUARD BODY 1
25 96T-620125 HEX. NUT 1 65 90623ZZ BALL BEARING (623ZZ) 7
26 96T-620052 GRIP 1 66 96X-620143 PLATEN PAD 2
27 96T-620127 GUIDE POST 1 67 96T-620147 SCREW THREAD INSERT
S
5
28 96T-620128 SUPPORT ROD 1 68 910014S HEX. KEY WRENCH 1
29 96T-620129 SCREW 1 69 940330 O-RING 1
30 96T-620130 SPRING 1 70 96T-620007 SCREW 1
31 96T-620131 TENSION ARM 1 71 9PN02001308 PIN (2X13.8) 1
32 96T-620132-0018S HANDLE 1 72 96T-620032 SCREW (M4X8L) 2
33 9960120 BALL BEARING (608ZZ) 1 73 940147 SPRING WASHER 2
34 96T-620145 SCREW THREAD INSERTS 1 74 96T-620034 NUT (M4) 1
35 966-6133C23 EXHAUST SHAFT 1 75 96T-620031 LEVER SUPPORT 1
36 96T-620136 SPRING 1 76 9OR02607108 O-RING 1
37 96T-620137 GUARD 1 77 982209 O-RING 1
38 9061038 BALL BEARING (684ZZ) 2 78 976010 O-RING 1
39 96T-620139-0018S KNOB 1 79 966-6133C25 MUFFLER 1
40 951540-228 SAFETY BAR 1 80 966-6133C24 EXHAUST SLEEVE 1
RPM .................................................................................................................... 18,000
Weight ................................................................................................................. 2.9 lbs
Length................................................................................................................. 15.35”
Max belt width ......................................................................................................... ¾”
Air Inlet ................................................................................................................ ¼NPT
Rec Hose ................................................................................................................ 3/8”