Universal Tool UT8789-5-332CV Datasheet

MODEL: UT8789-5-332CV
5” Orbital Palm Sander
Central Vac
Universal Tool
™

Important Warnings - Sanders & Polishers
1. Eye protection, safety gloves and safety aprons must always we worn when operating a sander or
polisher.
2. Never adjust the sander or polisher or change the backing pad, sanding disc, sanding belt or
polishing bonnet unless the air supply and air hose is disconnected from the tool
3. Only use backing pads and polishing backing pads that have a rated speed then same as the sander
or polisher or higher.
4. Never attempt to modify or adapt a sander or polisher for use with a grinding wheel or cut-off wheel
or wire brush.
5. Only personnel trained in the correct methods to change pads, sanding discs, sanding belts and
polishing bonnets should conduct these operations.
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply
Warranty
Limited Warranty: Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
Tool or its authorized service centers. If a UT tool proves defective in material or workmanship within one year after purchase, return
it to any authorized service center or Universal Tool freight prepaid. Please enclose your name, address and adequate proof of date of
purchase and a short description of the defect. Universal Tool will,at its option, repair or replace defective tools free of charge. Repairs or
replacements are warranted as described above for the remainder of the original warranty period. Universal Tool's sole liability and your
exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential or special damages,
or any other damages,costs or expenses excepting only the cost or expense of repair or replacement as described above.
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California
to cause cancer and birth defects or
other reproductive harm. .
For more information go to www.P65Warnings.ca.gov
Pad Size Orbit Pad Free Speed Weight Length Height Air Inlet Rec.
UT Model No. Description (in) mm (in.) Type (RPM) (lbs) w/pad (in) w/pad (in) (NPT) Hose Size
UT8789-5-332CV ORBITAL CENTRAL VAC PALM SANDER 52.5mm (3/32) PSA 12,000 2.0 8.2 4.3 1/4" 3/8"
Vibration Level (m/sec2): 0.8 Noise Level (dBA): 75

MODEL: UT8789-5-332CV
5” Orbital Palm Sander
Exploded View & Parts List
Universal Tool
™
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
01 9OB10601 HOUSING 1 28 9STOB-25 FRONT PLATE 1
02 9OB-03 SNAP RING 1 29 9OB-26A BEARING 1
03 9OB-04 O-RING 1 30 9OB-28 WASHER 1
04 9OB10604 VALVE STEM 1 31 9E-29 WASHER 1
05 9SX-11 SILENCER 2 32 9ST70407 ROTOR KEY 1
06 9OB-02 O-RING 2 33 9ST25-100-5 MOTOR SHAFT BALANCER 1
07 9ST-OB10607 REGULATOR 1 34 9OB-30 SNAP RING 1
08 9OB10608 LEVER 1 35 9OB-31.3 BEARING 1
09 9OB10609 HOUSING COVER 1 36 9OB-23.2A SHIM 1
10 9OB10610 SPRING PIN 1 37 9OB-31.4 BEARING 1
11 9OB10611 MUFFLER 1 38 9RS0132A DUSTPROOF WASHER 1
12 9OB10612 PACKING 1 39 9OB-33 SNAP RING 1
13 9OB10613 EXHAUST SLEEVE 1 40 9S560-34 SHAFT 1
14 9OB-06 WASHER 1 41 9OB-16.1 WASHER 1
15 9STOB-08 VALVE 1 42 9OB10642-2 HOUSING COVER 1
16 9OB-09-1 SPRING 1 43 9OB10643 SCREW 1
17 9OB10617 AIR INLET (NPT) 1 44 9OB10644 LOCK NUT 1
18 970410 SNAP RING 1 45 9OB10645 SHROUD 1
19 970048A BEARING 1 46 9BTOB-38-5P5Y PAD PSA 1
20 9OB-16.2 RUBBER BUSHING 2 47 9OB10647-1 DUST HOSE 1
21 9STOB-19 REAR PLATE 1 48 9ST-OB10648C VACUUM ADAPTER 1
22 9OB-20-2 ROTOR BLADE 5 49 9BTOB-39-22 STOP SPANNER 1
23 9STOB-21 ROTOR 1 50 9OB106C50 MUFFLER BODY 1
24 9ST246021A CYLINDER 1 51 9OB10651 SLEEVE 1
25 9ST246014 PIN 1 52 9RS0133 WASHER 1
26 9ST241624 BUSHING 1 53 9SX-11A SILENCER 1
27 981326 PIN 1

Universal Tool a Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter FL 33458