UPC 8162C User manual

PART Quantity Reference
Push Pin 26 (2 extra) A
Trusshead Screw 20 (2 extra) B
Header Clip 2C
ASSEMBLY INSTRUCTIONS
PARTS BAG UPC 8162C Double 144 Pocket Spinner
PARTS LIST
B
PART Quantity Reference
Top Cap 2D
Tower Panel 6E
Base 1F
Pockets 144 G
Tower Helper 2H
G
C
TOOLS REQUIRED: #2 Phillips Screwdriver
A
D
H
E
Page 1 of 5
Revised 01/08/19 U.S. PATENT NO.
8,534,472
Instruction Video
Watch our easy
to follow
instruction video
www.upcdisplays.com/8162C
F
Finished Display
Thank you for your purchase of one of many fine products designed & manufactured by UPC.
We have made every effort to make your assembly easy, clear & hassle free. For more information
or if you have any questions contact customer service at 1-800-859-7442.

Small Hole
(align behind
Large Hole)
Facet with
Large Hole
(align in front
of Small Hole)
A
A. Peel protective masking off
Tower Panels (E) before assembly.
B. Overlap each Tower Panel (E) so the large hole
of facet lies outside the small hole of
adjacent panel. (see figure BELOW)
C. Use Large Finger Holes (see figure RIGHT)
to hold Tower Panels (E) tightly
together while installing Push Pins (A).
D. Join (3) Tower Panels (E) together
using (12) Push Pins (A). (see figure RIGHT)
1
E
E
Tower Panels (E)
MUST be aligned properly
at facets BEFORE securing
with Push Pins (A).
NOTE:
Push Pins CANNOT be
removed once
inserted into holes!
(finger hole)
(finger hole)
(finger hole)
A
ASSEMBLY
Page 2 of 5
U.S. PATENT NO.
8,534,472
ASSEMBLY
(finger hole)
close up view

Align corresponding
holes and set the
Tower Panel
Assembly (E)
onto the Base (F).
3
H
F
This step will hold Tower Panel Assembly (E)
up for installation to
Base Assembly. Insert
(2) Tower Helpers (H)
under Spinner Plate
on Base (F), as
shown to the right.
2
E
Page 3 of 5
U.S. PATENT NO.
8,534,472
ASSEMBLY
F
HOLES

REPEAT STEPS 1-6
FOR 2nd TOWER.
H
Page 4 of 4
Page 4 of 5
U.S. PATENT NO.
8,534,472
ASSEMBLY
6Remove Tower Helpers (H).
4
Continue to secure Tower Panel Assembly (E)
to Base (F) at corner holes of Tower Panel
Assembly. Attach panels to Spinner Plate edge
with (3) Trusshead Screws (B).
Tighten all (6) securely!
5
B
Secure Tower Panel Assembly (E) to Base (F)
at middle holes of Tower Assembly. Attach Tower
Panels to Spinner Plate edge with
(3) Trusshead Screws (B).
DO NOT tighten completely!
B
B
E
F
F
E

Attach (2) Header Clips (C) to top of Tower Panel Assemblies (E) using attached
Double Sided Tape.
Attach (2) Top Caps (D) to the top of the Tower Panels Assemblies (E) using
(3) Trusshead Screws (B) for each Top Cap (D).
D
B
E
7
Page 4 of 4
Page 5 of 5
U.S. PATENT NO.
8,534,472
ASSEMBLY
Attach Pockets (G) by hooking the side
tabs into the vertical slots in the
Tower Panel Assemblies (E).
Lock Bottom tongue of Pockets (G) into
the horizontal slots on the
Tower Panel Assemblies (E).
Each Vertical Slot holds two Pockets (G)
side by side.
G
E
C
9
8