Uplift Desk MON001 User manual

®
Zilker Single Monitor Arm
MON001
© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
AI-MON001-1.0
Note: There are two ways to attach this monitor arm to your desktop: Clamp and Bolt-thru assembly. Determine if you need
to attach it around the back side of your desk (follow Step 1.1) or through a hole from .4’’ to 3.15’’ in diameter (follow Step 1.2).
Step 1.1 - Clamp
Peel the adhesive and attach the Base cushion to the underside of
the Base, and rest the Bottom plate onto the Base’s bolt. Fit the
Base around the back of the desk and tighten the Clamp-bolt &
Bottom plate into place using the 6.5mm Allen wrench.
Step 1.2 - Bolt-thru
To mount your monitor arm through a hole in your desktop (min
.4’’, max 3.15’’ in diameter) rst loosen the big screw inside the
clamp with the 6mm Allen wrench. Note: screw may be tight.
Once removed, separate the clamp assembly from the Base.
Line up the Base plate inside the Base. Remove the adhesive on
the Base cushion and apply across both parts, ensuring it is ad-
hered properly.
Cover the hole with the assembly, with the logo facing the front
of desk. Select a Long bolt. The 50mm Bolt ts desks .6’’ to 1.38’’
thick. The 70mm Bolt ts desks 1.38’’ to 2.13’’ thick. Insert the Long
bolt thru the Bottom plate. Note: Bottom Plate must be wide
enough to straddle the hole’s diameter. Thread the bolt into the
Base assembly by hand and tighten using the 6mm Allen wrench.
Step 2
Insert the Extension arm into the Base. *Note: The stopping-pin
in the Base restricts arm rotation to 180°. If you want a full 360°
rotation, remove this pin with the 1.5mm Allen wrench.
Insert the Spring arm into the Extension arm.
To prevent the arms from being lifted out, tighten the set
screws on the back of the Base where the Extension arm joins
it, and on the front of the Extension arm where the Spring arm
joins it with the 2.5mm Allen wrench.
*
Note:
If the Clamp does not t on your desk, increase or decrease the
span of the clamp by removing the Bottom clamp and Bolt, and
repositioning them. First, unscrew the two screws holding the
Bottom clamp with the 4mm Allen wrench (see g. 1).
For thin desks (.75’’ minimum) reassemble the clamp as shown
in Figure 2. For the thick desks (3.75’’ maximum) reassemble the
clamp as shown in Figure 3.
Once the Clamp has been set and ts your desktop, continue on
to Step 2 below.
g. 1 g. 2 g. 3
Bottom plate Base Plate
Base
Base Cushion
Parts for Bolt-thru assembly
Vesa mount
Monitor screw
(qty 4) Long bolts
(two sizes included:
50mm & 70mm)
Allen wrenches
(set of six:
1.5mm, 2.5mm, 4mm, 5mm, 6mm, 6.5mm)
Spring arm
Extension Arm
Package Contents
min. desk
thickness
.75’’
max desk
thickness
3.75’’

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 3
Place monitor face down on a at surface, making sure not to
scratch the screen. Attach the VESA mount to the back of the
monitor using a Phillips screwdriver and the four (4) Monitor
screws provided. The mount is designed to t the industry stan-
dard VESA 75mm & 100mm hole patterns. Note: Make sure the
tab on the VESA mount is facing the top of the monitor.
Step 4
Slide the VESA mount down into the slot at the end of the Spring
arm until you hear it click in place.
When you move the monitor to new position, the arm should
hold that position. If it doesn’t, you’ll need to adjust the arm’s
counterbalance. Use the 5mm Allen wrench on the set-screw
located at the top-center of the Spring arm.
If the monitor is too heavy and pulls the arm down, turn toward
the “+” to increase arm resistance. If the monitor is too light
and rises up, turn toward “-” to reduce arm resistance. Keep
adjusting until the arm holds your monitor in place regardless
of where you move it.
Step 5
You can run your montior’s wires through the built-in wire man-
agement features.
Under the Spring arm, you can press the wires into this clip.
(see g. 1).
Inside the Extension arm is a channel accessible by a removable
cover. Slide the cover up & out to place your wires, then replace
the cover in the reverse motion, in & down. (see gs 2-3)
Step 6 Monitor Ergonomics
Screen Distance: Set screens about an arm’s length (approxi-
mately 18’’-28’’) from your eyes. If print is too hard to read, it is
better to make the print larger on your screen than to move the
screen closer.
Monitor Height: The top of the monitor should be level with
your eyes.
Monitor Tilt: The monitor should be tilted slightly up so it’s eas-
ier to see the screen when the top of the monitor is level with
your eyes. If the ball-joint holding the monitor does not move,
loosen each screw using the 4mm Allen wrench. This should
only take a couple of turns, each. If you loosen too much, and
the monitor does not stay in place, tighten slightly.
Copyright Notice: This guide is a component of the Zilker Single monitor arm. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.
com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
CAUTIONS & WARNINGS
!
!
g. 1 g. 2 g. 3
IMPORTANT NOTE: Monitors weighing outside the weight range of 4.4lb min. and 11 lb. max. (2-5kg) will not work on this arm!