Uponor BT DP-01 User manual

Wireless thermostat
user guide
DE BEDIENUNGSANLEITUNG
DK BRUGERVEJLEDNING
FR GUIDE D’UTILISATION
NL HANDLEIDING
SE BRUKSANVISNING
05 I 2014

2
WIRELESS THERMOSTAT USER GUIDE
IMPORTANT!
Before starting work the installer should carefully read this Installation &
Operation Manual, and make sure all instructions contained therein are
understood and observed.
- The thermostat should be mounted, operated and maintained by specially
trained personnel only. Personnel in the course of training are only allowed
to handle the product under the supervision of an experienced fitter. Subject
to observation of the above terms, the manufacture shall assume the liability
for the equipment as provided by legal stipulations.
- All instructions in this Installation & Operation manual should be observed
when working with the controller. Any other application shall not comply with
the regulations. The manufacturer shall not be liable in case of incompetent
use of the control. Any modifications and amendments are not allowed for
safety reasons. The maintenance may be performed by service shops
approved by the manufacturer only.
- The functionality of the controller depends on the model and equipment.
This installation leaflet is part of the product and has to be obtained.
APPLICATION
- The thermostats of the “BT” series are developed to control and manage all
type of heating installations.
- The controllers have been designed for use in residential rooms, office
spaces and industrial facilities.
Verify that the installation complies with existing regulations before operation
to ensure proper use of the installation.
SAFETY INSTRUCTIONS
Before starting work disconnect power supply!
- All installation and wiring work related to the thermostat must be carried
out only when de-energized. The appliance should be connected and
commissioned by qualified personnel only. Make sure to adhere to valid
safety regulations.
- The thermostats are neither splash- nor drip-proof. Therefore, they must
be mounted at a dry place.
- Do not interchange the connections of the sensors and the 230V
connections under any circumstances! Interchanging these connections may
result in life endangering electrical hazards or the destruction of the
appliance and the connected sensors and other appliances.
U
K

3
WIRELESS THERMOSTAT USER GUIDE
Table of content
1 Presentation........... 4
1.1 Keyboard............... 5
1.2 Display & LED......... 5
2 First Installation ..... 6
2.1 Batteries installation 6
2.2 Time and Date adjustment 7
2.3 RF installation ........ 7
2.4 Starting................. 8
3 Working mode definition 9
3.1 Manual mode Comfort 9
3.2 Manual mode, Reduced 10
3.3 OFF mode ............. 10
3.4 Automatic mode ..... 10
3.5 Program mode ....... 10
3.6 Holiday mode......... 15
3.7 Timer mode .......... 15
4 Special function...... 16
4.1 Keyboards lock Function 16
4.2 Information............ 16
5 Parameter’s menu... 17
6 Technical characteristics 19
7 Troubleshooting & Solution 20

4
WIRELESS THERMOSTAT USER GUIDE
1 Presentation
Electronic programmable thermostat with LCD display specially designed to
control different type of heating systems.
It will be your best partner to optimize your energy consumption and
increase your comfort.
- Modern design with soft touch material
- Wiring & Installation simplified
- “Easy program creation” function
- Weekly programmable by step of 30 min
- Temporary override function
- Anti-freeze function
- Holiday or Reception function
- EEPROM non-volatile memory
- 2 AAA batteries for 2 years operating life
- 2 Wires output for a maximum possibility of use
- 2 parameter menus (user and installer)
In option
- External sensor with several possibilities of regulation (floor, combined…)
+
+
-
-

5
WIRELESS THERMOSTAT USER GUIDE
1.1
Keyboard
Left Navigation key (
◄ )
Right navigation key (
► )
Escape key ()
Edition key ()
1.2
Display & LED
Red Fix (when backlight is lit up): Heating demand
Green flash: your validation is required
Red flash: Error on sensor or batteries
1.
Current day of the week
2.
Operating mode menu (active mode is framed).
Minus Key (-) Plus Key (+)
Validation Key (OK) Status LED
1 2
3
4
5
6
7
8
9
12 11 10
15
14
13

6
WIRELESS THERMOSTAT USER GUIDE
3. Program number or parameter number if “4” is displayed.
4.
Installation Parameter menu.
5.
RF transmission logo.
6.
Type of sensor used and temperature displayed.
Regulation => Internal or external ambient sensor.
Regulation => Floor sensor.
Regulation => Internal sensor with Floor limitation.
View of the outside temperature
7.
Heating demand indication.
8.
Low batteries indicator.
9.
°C or °F unit indicator
10.
Setting or measured temperature if “5” is displayed. Parameter value if
“4” is displayed.
11.
Temporary override function activated, or “ITCS” function if blinking.
12.
Time or parameter title if “4” is displayed.
13.
Program of the current day (the current time bar blinks)
14.
Pictogram for program creation, program state in normal operating
mode.
15.
Key lock indicator
2 First Installation
This section will guide you to set up your thermostat for the first time.
2.1
Batteries installation
- Open the two side’s covers and Insert the 2 AAA Alkaline supplied batteries
(or remove the small protection sticker if the batteries are already installed
in the compartment)
- Close the two side’s covers.
- Now your thermostat will propose you to adjust the current time and date.

7
WIRELESS THERMOSTAT USER GUIDE
2.2 Time and Date adjustment
Each time a value blinks, you can adjust it with the (-) and (+) keys, once
the value is chosen, validate it with the (OK) key. The thermostat will jump
automatically to the next value.
Note: you can always come back to the previous value by pressing the
escape key ().
List order of the time and date adjustments:
Time and day:
Adjustment of the hours,
Adjustment of the minutes
Adjustment of the day (1 = Monday)
Date:
Adjustment of the day number
Adjustment of the month number (01 to 12)
Adjustment of the year (Century)
Adjustment of the year
Then the message “Save” and blinking green LED appears, press (OK) to
validate the adjusted time and date.
You can always reach the time and date adjustments, by pressing and
maintaining the edition ()key during 2 seconds in normal operating modes.
2.3
RF installation
- First of all to configure your thermostat with the receiver, you must put
your receiver in « RF init ». mode. (please refer to the receiver leaflet for
this, only the RF receiver of the same range are compatibles)
- Now on the thermostat press and maintain the edition key ()during 10s,
then the parameter « ini » must be display.
The thermostat will send now the radio configuration signal to the receiver.
- On the receiver check the good reception (generally showed by a green
LED blinking). Once the configuration between the receiver and the
thermostat made, press on the escape key ( ) to come back to the main
screen.

8
WIRELESS THERMOSTAT USER GUIDE
- Now you can check the RF distance, go to the room which must be
regulated. Put your thermostat on the final position (On the wall or
table...), then put the thermostat in Comfort mode (setting temperature
position 37°C). Close the door and go to the receiver to check if the new
status of the thermostat has received. (The heating is generally showed by
a Red LED).
- Now return to the thermostat and switch off it. Check on the receiver again
if it’s also switched off (The red LED must be turned off)
oIf the RF signals were received correctly, adjust your setting temperature
as you want.
oIf the RF signals weren’t received correctly, check the installation
(Receiver position, distance...)
* To make the installation easier it will be better to have the thermostat near
to the receiver during the configuration mode. (A minimal distance of >
1 meter must be respected)
2.4
Starting
The thermostat is now ready to works.
The default working mode will be automatic with a standard built-in
program “P1”.
Monday to Friday
20°C
18°C
07:00 09:00 17:00 23:00
Saturday & Sunday
20°C
18°C
08:00 23:00

9
WIRELESS THERMOSTAT USER GUIDE
Note:
You can customise your program as you want, See the next part “Working
mode definition” chapter “Program” for more explanation
At any time, when the backlight is extinct, press the (OK) key to lit-up the
backlight,
and then press another time the (OK) key to show the current
setting temperature.
3 Working mode definition
How to change the working mode?
- Open the small center cover to have access to the navigation keys (
◄ )or
(
► ).
- You can now press theses keys to display the working mode line.
Move the frame cursor on the desired working mode and press (OK) to enter
in the operating mode you have chosen.
3.1 Manual mode Comfort
Manual working mode, the comfort setting temperature will be followed all
the time.
By pressing (-) or (+) keys, the comfort setting temperature starts to blink
and can be adjusted.
Curent stage
of the program
Curent time
Program
followed

10
WIRELESS THERMOSTAT USER GUIDE
3.2 Manual mode, Reduced
Manual working mode, the reduced setting temperature will be followed all
the time.
By pressing (-) or (+) keys, the reduced setting temperature starts to blink
and can be adjusted.
3.3
OFF mode
Use this mode if you need to switch off your installation.
Be Careful:
In this mode your installation can freeze.
- At any time, when display is off, press on the (Ok) key to display a few
seconds the current temperature and time.
- To restart your installation, use the navigation keys (
◄ )or ( ► ).
3.4
Automatic mode
In this mode the thermostat will follow the chosen program (Built-in or
customized) according to the actual time and the Comfort and Reduced
setting temperatures.
You can easily override, until next program step, the current program
temperature by changing the value with (-) or (+). Setting temperature will
blink.
The small hand logo will be displayed when override function is active.
If hand logo blinks then ITCS is ongoing.
3.5
Program mode
When you enter in the Program mode, the first operation is to choose the
program number
with (-) or (+) keys.
Current day
Program
of the day
Program
followed

11
WIRELESS THERMOSTAT USER GUIDE
You can choose between a built-in program P1 to P9 or a user program U1
to U4.
If you chose a Built-in program P1 to P9,
You can only see and chose the program.
P1: Morning, Evening & Weekend
P2: Morning, Midday, Evening & Weekend
P3: Day & Weekend
P4: Evening & Weekend
P5: Morning, Evening (Bathroom)
P6: Morning, afternoon & Weekend
P7: 7H – 19H (Office)
P8: 8H – 19H & Saturday (Shop)
P9: Weekend (Secondary house)
(See the Annexe parts to view a complete description of the Built-in
program)
- Use the navigation keys (
◄ )or ( ► )to change the program day displayed.
- Press the (OK) key to confirm your choice and come back to the main
screen (in AUTO mode)
If you chose a user program U1 to U4,
As above you can choose the program, see it,
but you can also customise it.
Default setting:
U1, U2, U3, U4 = Comfort all week
- Press on the edition key ()to customise a user program.
Symbols and explanation for program creation:
First step of the day ( Comfort temp.)
The wakeup hour need to be adjusted.

12
WIRELESS THERMOSTAT USER GUIDE
Middle step of the day ( Reduced temp.)
The leaving hour need to be adjusted
Middle step of the day ( Comfort temp.)
The comeback hour will need to be adjusted
Last step of the day ( Reduced temp.)
The sleeping hour need to be adjusted
- The program step is 30 minutes
- Each time a value or icon blinks you are invited to make a choice with (-)
or (+) keys,
once the choice is made press the (OK) key to jump to the following step.
- The program creation will always start with the day 1(Monday).
Once you have pressed the ()key, the following display will appear:
Now you are invited to adjust the hour of the first step of the program with
(-) or (+),
Press (OK) to validate and go to the following step.

13
WIRELESS THERMOSTAT USER GUIDE
Now you are invited to choose the type of the next step of the program
(blinking icons),
2 choices will be possible:
- 1
st
choice is to choose the sleep icon. (End of the day)
- 2
nd
choice is to choose the leaving icon, to add one step to the program
during the day.
When the choice is made, press (OK) to validate.
Then you can adjust the step hour with (-) or (+),
When step hour is set press (OK) to jump to the next step.
You will be directly invited to adjust with (-) or (+) the hour of the
comeback step.
Press (OK) to validate and go to the following step.

14
WIRELESS THERMOSTAT USER GUIDE
You are again invited to choose the type of the next step of the program
(blinking icons),
2 choices will be possible:
- 1
st
choice is to choose the sleep icons. (End of the day)
- 2
nd
choice is to choose the leaving icons, to add another step to the
program during the day.
When the choice is made, press (OK) to valid and you can adjust the hour of
this step with (-) or (+),
Press (OK) to validate and finish the edition of the first day.
Now you can choose to copy the program day just created to subsequent
days.
Change the choice “Yes” or “no” with (-) or (+) and validate your choice
with (OK).
- If you select “no”, you will be invited to create a program for Tuesday
(repeat the previous method to build it.)
- If you select “Yes”, you will have the possibility to copy the program to the
following day (on Tuesday on Wednesday... up to the last day of the week
(7 Sunday).
When you press (OK) on the last day (7 Sunday) you will be invited to
“SAVE” your program.

15
WIRELESS THERMOSTAT USER GUIDE
Then the message “Save” and blinking green LED appears:
Press (OK) key to save your program and return to AUTO operating mode
following your user program.
Press the escape key ()to erase your user program changes and come
back to operating mode.
3.6
Timer mode
The Timer mode allows you to adjust, the temperature and the duration for a
special time.
This function can be used when you stay at home for several days, or if you
want to override the program for some time (reception...)
- You can first adjust, the duration in hours “H” if below 24H, then in day “d”
with (-) or (+), press (OK) to validate. (Adjustable 1 Hour to 99 days)
- In a second time, you can adjust the desired setting temperature with (-)
or (+), press (OK) to start the function. (Default value 22°C)
The logo will be blinks and the number of hours /days left is displayed until
the end of the period.
If you want to stop the Timer function before the end, set the duration period
to “no” with (-) key.
3.7
Holiday mode
The Holiday mode allows you to set the anti-freeze temperature for a
selected number of days
- You can adjust, the duration in day “d” with (-) or (+), press (OK) to start
(adjustable 1 to 99 days)

16
WIRELESS THERMOSTAT USER GUIDE
- The anti-freeze setting temperature is fixed and can be adjusted in the
parameter menu number
06 ‘HG’, see chapter 6. (Default value 10°C)
The logo will blink and the number of days left is displayed until the end
of the period.
If you want to stop the Holiday function before the end, set the duration
period to “no” with (-) key.
4 Special function
4.1
Keyboards lock Function
Use this function to prevent all change of your settings (In a child room,
public area…)
- To activate the Key lock function, first press maintain the escape key ()
and then press simultaneously on the edition key ().
- The “ ” logo will be displayed on the screen.
- Repeat the same procedure to unlock the key board.
4.2
Information
With this function You can quickly view all currents temperatures of the
probe sensors connected to your thermostat (Floor, external or outside
sensor) by several presses on the escape key ().This “Scroll function” is
only available in the main screen.
You can view:
- The current setting temperature followed by the thermostat.
- The ambient temperature
- If external sensor is connected:
The Floor temperature if it is used as floor sensor.
The outside temperature if it used as outside sensor.
If Parameter “SenS” is set on “Air”, the external sensor will be used as an
outside temperature sensor

17
WIRELESS THERMOSTAT USER GUIDE
5 Parameter’s menu
Your thermostat has a parameter’s menu, in order to enter in this menu,
press and maintain the edition key ()during 5sec. Then parameter menu
will appear and first parameter screen will be displayed:
Now you can select a parameter which must be adjusted with the navigation
keys (
◄ )or ( ► ), once the parameter chosen, toggle the value with the
(OK) key, modify it with (-) or (+) and confirm your adjustment with (OK).
To leave the parameter menu, choose the parameter « End » and press
(OK).
N° Default value & other possibilities
00 RF INI: Radio configuration
Sends the radio link signal in order to assign this RF Thermostat with
it’s RF receiver.
You also need to set simultaneously the receiver in radio
configuration mode (On a simple receiver press and maintain button
until the green light lit’s up, see receiver leaflet)
01 dEG: Unit of the temperatures displayed
°C Celsius
°F Fahrenheit
02 __:__ Selection of the Time clock unit
24H (24:00)
12H (12:00 AM /PM)
03 dst: Daylight Summer time change Summer<->Winter
YES automatic change according to date.
no no daylight summer time automatic change.
04 AirC: Calibration of the internal probe
The calibration must be done after 1 day working with the same
setting temperature in accordance with the following description:
Put a thermometer in the room at 1.5M distance from the floor (like
the thermostat) and check the real temperature in the room after 1
hour.
When you enter on the calibration parameter “no” is displayed on the
right to indicate no calibration has made.

18
WIRELESS THERMOSTAT USER GUIDE
To enter the value shown on the thermometer, use the (-) or (+)
keys to enter the real value. Then, press (Ok) to confirm.
The message “Yes” should be displayed; the value will be stored in
the internal memory.
If you need to erase a calibration press on the escape key ().
The old value will be erased and the message “no” will be displayed.
* Pay attention:
Only the heating element driven by the thermostat must be used
during the complete step of the calibration.
05 OutC , AMbC , FlrC: Calibration of the external wired probe
Same calibration method as described in parameter
“04 AirC” above.
06 HG: Anti-freeze temperature used in Holiday mode
Default value 10°C.
Use the (-) or (+) keys to change the anti-freeze setting
temperature. Then press (Ok) to confirm.
07 ITCS: YES, no
The Intelligent Temperature Control System will activate your
installation in advance (2 hours maximum) to assure the desired
temperature at the hour programmed following your weekly program.
This automatic control system works in the following way:
When you start your thermostat for the first time, it will measure the
time taken by your installation to reach the set temperature. The
thermostat will re-measure this time at each program change to
compensate external temperature change & influence. You can now
program your thermostat without the need to adjust the temperature
in advance because your thermostat does it automatically for you.
08 Clr ALL: Reset to Factory setting
Press and maintain (Ok) key during 10s to reset Set points
temperatures and user parameters in this menu to factory default
settings. User programs will also be resetted.
Pay attention:
Ensure you that you have all necessary elements to re-setup your
installation before to use this function.
09 Software version
VErS ___
10
End: Exit the parameter’s menu
Press (OK) key to exit installation parameter menu and return to
normal operation.

19
WIRELESS THERMOSTAT USER GUIDE
6 Technical characteristics
Environmental:
Operating temperature:
Shipping and storage
tem
p
erature:
0°C - 40°C
-10°C to +50°C
Electrical
Protection
Installation
Category
Pollution Degree
IP30
Class II
2
Measured temperature
precision 0.1°C
Setting temperature
range
Comfort, Reduced
Holiday (Antifreeze)
Timer
5°C to 35°C by 0,5°C step
10°C (adjustable)
5°C to 35°C
Regulation
characteristics Proportional Band (PWM 2°C for 10min cycle) or Hysteresis of 0.5°C
Power Supply
Operating life 2 AAA LR03 1.5V Alkaline ~2 years
Sensing elements:
Internal & External
(
o
p
tion
)
NTC 10kat 25°C
Radio Frequency 868 MHz, <10mW.
Software version Showed in the parameter menu. Vers xxx
Norms and
homologation:
Your thermostat has
been designed in
conformity with the
following standards or
other normative
documents:
EN 60730-1 : 2003
EN 61000-6-1 : 2002
EN 61000-6-3 : 2004
EN 61000-4-2 : 2001
EN300220-1/2
EN301489-1/3
R&TTE 1999/5/EC
Low voltage 2006/95/CE
EMC 2004/108/CE

20
WIRELESS THERMOSTAT USER GUIDE
7 Troubleshooting & Solution
My BT DP-01 doesn’t start
Batteries Problem
- Check if the protection sticker on the batteries is
removed.
- Check the batteries orientation.
- Check the capacity of the batteries
My BT DP-01 Led, blinks in Red
Problem on sensors
The logo blinks (ambient sensor)
- Contact your installer or seller.
The logo blinks (Floor sensor)
- Check the connection of the sensor.
- Disconnect the sensor, and check it with an
ohmmeter
(the value must be around 10kohms)
Batteries level is too
less The logo blinks (Batteries)
- Re
p
lace the batteries.
M
y
BT DP-01 seems work correctl
y
but the heatin
g
doesn’t work correctl
y
Output
On the receiver:
- check the good reception of RF signal
- Check the connections.
- Check the power supply of the heating element.
- Contact your installer.
RF
communication
- Check the following points :
- The receiver must be put at a minimum distance of
50cm of all others electrical or wireless materials
(GSM, Wi-Fi..)
- The receiver shouldn’t be fixed on a metallic part
or too close of h
y
draulic
p
i
p
es…
(
Co
pp
er…
)