URC MRX-10 User manual

Owner’s Manual
MRX-10 Advanced Network
System Controller

MRX-10 Owner’s Manual ©2015 Universal Remote Control, Inc.
he information in this Owner’s Manual is copyright protected. No part of this
manual may be copied or reproduced in any form without prior written consent
from Universal Remote Control, Inc.
UNIVERSAL REMO E CON ROL, INC. SHALL NO BE LIABLE FOR OPER-
A IONAL, ECHNICAL OR EDI ORIAL ERRORS/OMISSIONS MADE IN
HIS MANUAL.
he information in this Owner’s Manual may be subject to change without prior
notice.
otal Control is a registered trademark of Universal Remote Control, Inc.
URC - Control the Experience is a registered trademark of Universal Remote
Control, Inc.
All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.
Universal Remote Control,Inc.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]

TABLE OFCONTENTS
Introduction 1
Features and Benefits 1
Parts Guide 1
Front Panel Descriptions 2
Rear Panel Descriptions 3
Specifications 4
Limited Warranty Statement 5
End User Agreement 7
Federal Communication Commission
Interference Statement 8
Declaration of Conformity 9

age 1
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Introduction
The MRX-10 Advanced Network System Controller controls all
MRX series connected devices throughout the entire home. Press a
button on a Total Control remote or keypad to issue a command
from the MRX-10 to turn off the lights in every room all while
watching a movie. View the artist name, song title and album art
your child is listening to in their room from a Total Control remote
or keypad. Also control whole house music from sources such as a
DMS-1200, DMS-100, SNP-1 and a PSX-2.
Features and Benefits
lStores and issues commands and macros for all IP, IR, RS-
232, Relay, Sensor and 12V controlled devices to MRX series
base stations in one system.
lProvides 2-Way communication with Total Control remotes
and keypads.
lControl URC Lighting with an optional RFTX-1 RF Transmitter.
lCan be programmed off premises via the internet.
lEasy rack-mounting via optional RM -1 rack mounting kit.
Parts Guide
The MRX-10 Advanced Network System Controller includes:
1 - MRX-10 Network System 1 - Ethernet Cable
1 - AC Power Adapter 8 - IR Emitters with standard 3.5mm
1 - Power Cord plugs
1 - Adjustment Tool 1 - Installation Manual

age 2
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Front Panel Descriptions
The front panel consists of 2 indicator lights which will illuminate
when in use.
Power LED: Indicates that the MRX-10 is powered on when lit.
Ethernet LED: Indicates the network connectivity status of the MRX-
10. On=Connected, Off=not connected, Blinking=attempting to
connect.
Total Control Illumination: Attractive, adjustable accent lighting.
Reset: Press for one second and release to reboot the MRX-10.
ower LED Reset Ethernet LED Total Control llumination

age 3
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Rear Panel Descriptions
The rear panel ports are:
DC 12V Power: Attach the included 12V DC 3.5A power supply here.
LAN Connection: RJ45 standard 10/100 Ethernet connection to the
local network.
URC USB Port: USB port for future expansion.
IR Outputs: Eight standard 3.5mm IR emitter ports with individual
output level adjustment screws.
Relays NO, NC, COM: Two programmable relays to be normally
opened (NO), normally closed (NC) or momentary contacts. An
application should be less than 30V/.5A.
Sensors: Four sensor ports allow programming of state dependent
and triggered macros. Compatible with URC Video (URC part: VID)
and voltage (URC part: VS-100) sensors.
12V OUT: Two programmable 12V/0.2A outputs. Each may be pro-
grammed to turn on, off or momentarily toggle its output.
RS-232: Four RS-232 ports support Tx(Transmit), Rx(Receive) and
GND(Ground) connections for two way communication.
Compatible with URC cables RS232F and RS232M.
Trigger In: IR and RF trigger input ports allow integration with other
control systems and remotes.
RFTX-1: Attach an optional RFTX-1 transmitter to control URC
Lighting products via 418MHz or 433.92MHz wireless RF.
DC 12V
ower
URC
USB
Relay: NO,
NC, COM
12V Out Trigger In
RFTX-1
RS-232
ortsSensorsIR Outputs: #1-8LAN

age 4
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Specifications
Input & Outputs:
l12V/.2A: Two (Programmable)
lIR: Eight adjustable output
lUSB: One (for future use)
lEthernet: One 10/100 RJ45 port (Indicator 2LED)
lRS-232: Four, supporting TX, RX and GND
lSensor: Four, supporting Video or Voltage sensing
(requires URC sensors)
lRelays: NO, NC or COM
RF:
lFrequency: 2.4GHz (Two-way RF)
lRange: 50 to 100 feet, depending upon the environment
lPower Supply: 12v DC 3.5A External Power Supply
lSize: 1.7" x 17" x 8.7" (H X W x D)
lWeight: 4.5 lbs. (2.05 g)

age 5
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Limited Warranty Statement
1. Limited Warranty and Disclaimers
Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall
be free from defects in material and workmanship under normal usage for two
(2) years from purchase when such is purchased from URC. This limited
warranty is valid only in the United States of America. URC warrants that the
software will substantially conform in any material respect to its functional
specifications at the time of delivery. URC SHALL NOT BE LIABLE FOR
OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS AND/OR
OMISSIONS MADE IN THE URC DOCUMENTATION. URC DOES NOT
WARRANT THAT THE URC SOFTWARE IS BUG-FREE OR ERROR FREE OR
THAT THERE ARE NO ERRORS/BUGS IN THE URC SOFTWARE.
URC warrants that at the time of purchase the URC equipment and the URC
software complied with all applicable regulations and policies of the Federal
Communications Commissions (“FCC”) regarding electromagnetic interference
caused by electronic/computing devices and to the extent that the URC
equipment and/or the URC software fails to so comply, URC shall, at its own
expense, take all reasonable measures to promptly cause such to comply.
URC equipment purchases from other than an authorized URC dealer or
distributor are without warranty.
THIS LIMITED WARRANTY DOES NOT COVER TECHNICAL ASSISTANCE
FOR HARDWARE OR SOFTWARE USAGE EXCEPT AS EXPRESSLY
PROVIDED FOR HEREIN, THE EQUIPMENT, SOFTWARE AND
DOCUMENTATION OF URC ARE SUPPLIED “AS IS” WITHOUT ANY
WARRANTY, EXPRESS, STATUTORY OR IMPLIED, OF ANY IND. TO
THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC
EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS, STATUTORY OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. URC
DOES NOT WARRANT, GUARANTEE, OR MA E ANY
REPRESENTATIONS REGARDING THE USE OF, OR THE RESULTS OF THE
USE OF, THE EQUIPMENT, SOFTWARE OR DOCUMENTATION IN
TERMS OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE.
EXCEPT AS EXPRESSLY PROVIDED FOR HEREIN, TECHNICAL SERVICES
ARE SUPPLIED “AS IS”, WITHOUT ANY WARRANTY, EXPRESS,
STATUTORY OR IMPLIED, OF ANY IND. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, URC EXPRESSLY DISCLAIMS ALL
WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE WARRANTIES OF QUALITY OR REASONABLE

age 6
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
S ILL AND CARE, OR OUTCOME OR RESULTS. WITHOUT IN ANY WAY
LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN,
WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT
OR ACTS OF NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH
THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/
OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to end user in
whole or in part, where such are restricted or excluded by applicable law and
such shall apply to the maximum extent permitted by applicable law.
In the event of any warranty claim, URC will, at its sole option, repair the URC
equipment using new or comparable rebuilt parts, or exchange the URC
equipment for new or rebuilt equipment. In the event of a defect, these are the
end user’s exclusive remedies.
All the URC equipment returned for service, exchange or repair require an
RGA number. To obtain an RGA number, you must complete a Return
Request Form which you may obtain by calling [phone] or contacting
URC at [e-mail]. To obtain warranty service, end
user must deliver the URC equipment, freight prepaid, in its original packaging
or packaging affording adequate protection to URC at 420 Columbus Avenue,
Valhalla, NY 10595. It is the end user’s responsibility to backup any macro
programming, artwork, software or other materials that may have been
programmed into the unit. It is likely that such data, software, or other materials
will be lost during service and URC will not be responsible for any such
damage or loss. A dated purchase receipt, bill of sale, installation contract or
other verifiable proof of purchase is required. For the URC equipment support
and other important information, please visit URC's website available at
www.universalremote.com or call the Customer Service Center at (914) 835-
4484.
This limited warranty only covers the URC equipment issues caused by defects
in material or workmanship during ordinary consumer use. It does not cover
product issues caused by any other reason, including but not limited to product
issues due to commercial use, acts of God, third-party installation, misuse,
limitations of technology, or modification of or to any part of the URC
equipment. This limited warranty does not cover the URC equipment sold as
used, as is, refurbished, so called "B stock" or consumables (such as batteries).
This limited warranty is invalid if the factory applied serial number has been
altered or removed from the URC equipment. This limited warranty
specifically excludes the URC equipment sold by unauthorized resellers.
With the exception of URC’s IR-only, broad-based consumer remotes, none of

age 7
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
URC’s PC programmable remotes or any of our Total Control® whole-house
equipment are authorized for online internet sales. Buying URC’s PC
programmable remotes or any of our Total Control® whole-house equipment
online means buying equipment that does not have a URC’s limited warranty.
Such equipment is not eligible for URC tech support or software support,
either.
2. URC’S Limitations of Liability
IN NO EVENT SHALL URC BE LIABLE FOR INDIRECT, SPECIAL,
INCIDENTAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL DAMAGES
OF ANY IND OR LOSS OF PROFITS OR BUSINESS OPPORTUNITY,
EVEN IF URC IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL URC BE LIABLE FOR LOSS OF OR DAMAGE TO
DATA, COMPUTER SYSTEMS OR COMPUTER PROGRAMS. URC’S
LIABILITY, IF ANY, FOR DIRECT DAMAGES OF ANY FORM SHALL BE
LIMITED TO ACTUAL DAMAGES, NOT IN EXCESS OF AMOUNTS PAID
BY END USER FOR THE URC EQUIPMENT.
IN NO EVENT SHALL URC BE LIABLE FOR ANY EVENTS BEYOND ITS
CONTROL, INCLUDING ANY INSTANCE OF FORCE MAJEURE.
IN NO EVENT SHALL URC BE LIABLE FOR THE ACTS OR OMISSIONS OF
END USER OR ANY THIRD PARTY.
THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER IN
WHOLE OR IN PART, WHERE SUCH ARE RESTRICTED LIMITED OR
EXCLUDED BY APPLICABLE LAW AND SUCH SHALL APPLY TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.
URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS MADE
BY OTHERS.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS,
SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
END USER. THIS LIMITED WARRANTY GIVES END USER SPECIFIC LEGAL
RIGHTS AND END USER MAY HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE OR JURISDICTION TO JURISDICTION.
End User Agreement
The terms and conditions of the End User Agreement available at www.uni-
versalremote.com/eua.php shall apply.

age 8
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one more of the
following measures:
uReorient or relocate the receiving antenna.
uIncrease the separation between the equipment and receiver.
uConnect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
uConsult the dealer or an experienced radio/TV technician for
help.
Warning!
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Federal Communication Commission (FCC) Radiation Exposure Statement
The device and the antenna for this device must be installed to ensure a
minimum separation distance of 20 cm more from a person's body. Other
operating configurations should be avoided.

Declaration of Conformity
Company Name : Universal Remote Control Inc.
Company Address : 500 amaroneck Avenue, Harrison, NY 10528, U.S.A
Contact Info rmation : www.universalremote.com
Phone: [phone] Fax: [phone]
Brand Name : UNIVERSAL remote control
Product Name : NETWORK BASE STATION
odel Name : RX-10
This product herewith complies with the requirements of E C Directive (2004/108/EC)
and R&TTE Directive(1995/5/EC) issued by the Commission of the European Community
Compliance with these directives implies conformity to the following European Community
n E C Directive
l EN 55022(2010) l EN 55024(2010)
l EN 61000-3-2(2006)+A1(2009)+A2(2009) l EN 61000-3-3(2008)
l AS/NZS CISPR 22(2009)+A1(2010)
n R&TTE Directive
l EN 60950-1(2006) + A11(2009) + A1(2010) + A12(2011)+A2(2013)
l ETSI EN 62479(2010)
l ETSI EN 301 489-1 V1.9.2 (2011) l ETSI EN 301 489-17 V2.2.1(2012)
l ETSI EN 300 328 V1.8.1 (2012)
List of test reports and/or certificate verified compliance with the standards above
Date of issue : January 9, 2015
Name and signature of authorized person :
n E C Directive
l Report No.
l Testing Laboratory : Gumi College E C Center
n R&TTE Directive
l Certificate No.
l Certificate Body : TUV Rheinland (No. 0197)
Quality Assurance Team
OHSUNG ELECTRONICS CO., LTD.
age 9
MRX-10 ADVANCED NETWORK SYSTEM CONTROLLER

age 10
NOTE

OCE-0099A Rev 02
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]
www.universalremote.com