Urmet Dialog Ourten OT-PLC602 User manual
Page 1 of 7
Model OT-PLC602
Ethernet Extender
OT-PLC602 Ethernet Extender is a high-speed Ethernet transmission device.
It can transmit Ethernet signal over any 2-wire cable such as coax cable,
Cat5 cable, telephone cable, power line and so on. The max distance can reach
,000 meters and the max physical bandwidth can reach 500Mbps.
This device contains the Master unit and Slave unit, which supports point-to-point and point to multi-point network
transmission. It can greatly simplify the project cabling and apply to expand network system and transmit Ethernet
signal for long distance.
IP Video Surveillance Network Smart Home
Elevator IP Surveillance Intelligent Network Industry
Page 2 of 7
Max transmission distance can reach ,000m (RVS 2 mm2)
Max physical bandwidth can reach 500Mbps
Support power over cable technology (0-220V)
Plug and play, transparent transmission, no adjustment and no need to change the upper software
Low power consumption, communication channel dynamic adjustment and high performance error correction coding
technology
Telephone Line: Cat 3 or above Power Line: RVV, RVS, UTP Cable: Cat 5 or above
RVVP, RVB 2×0.5mm2
RJ45 port by EIA / TIA568B Power Adapter by 2VDC/ A, 5mm female power port (Optional)
Page 3 of 7
Category Description
Power
Available Voltage Range 2VDC 0%
Power Consumption / PC
Transmission / Rate
Standard Compliance IEEE 90 , IEEE802.3
Up Down Agreement CSMA/CA
Physical Speed 500Mbps
Encryption Way 28-bit AES Encryption
Physical Characteristic
Dimensions (L × W × H) 98mm×86.5mm×25mm
Material Aluminum
Net Weight 50g / PC
Operating Environment
Working Temperature -20 60
Working Humidity 95% (Non-condensation)
Page of 7
Tips: OT-PLC602 Ethernet Extender signal belongs to high frequency radio frequency signal. Considering the cable
loss, please choose better quality connectors.
The graph below shows OT-PLC602 transmission distance and network data rate. The data differs from the cables
types. When you use this device, please choose the suitable cables in line with your demands.
The above data for TCP throughput is the measured data in the actual environment. The maximum physical layer data
is 500Mbps. For coaxial cable transmission, performance is more stable, but it also affected by the cable and terminal
matching methods. The above tests are all finished in the field test.
Master
Slave
Step Installation Instruction Step Installation Instruction
Local network equipment is connected to RJ45
port of master unit ( ) 8 The connection terminal of A line of 2-wire (8)
2 The connection terminal of A line of 2-wire (2) 9 The connection terminal of B line of 2-wire (9)
3 The connection terminal of B line of 2-wire (3) 0 Connect the UTP cable of network equipment to
RJ45 port of slave unit ( 0)
4 Connect power supply ( 2VDC) to the power
port (4) Connect power supply ( 2VDC) to the power port
( )
5 Power indicator is always on (5) 2 Power indicator is always on ( 2)
6 Network data indicator quickly blinks when data
transmission is normal (6) 3 Network data indicator, it quickly blinks when data
transmission is normal ( 3)
7
Line indicator is on (In one line, the indicator is
always on when powered firstly, indicator is
always flash when powered later) (7)
4
Line indicator quickly blinks (In one line, the
indicator is always on when powered firstly,
indicator is always flash when powered later) ( 4)
Page 5 of 7
Figure 1 - Typical Installation
Most installations that use the OT-PLC602 involve the replacement of old analog equipment with new IP devices, while
reusing the installed wire. In generally, there are two connections types. One is typical connection (Figure 1 above).
And the other is Bus-architecture and Daisy Chain Connection (Figure 2 and 3 Below). You can choose the
connection type in line with actual environment.
Figure 2 - Bus-architecture Connection
Page 6 of 7
Figure 3 - Daisy Chain Connection
OT-PLC602 supports multicast function which can realize one point to multi-point data forwarding, to improve
transmission efficiency.
Figure 4- Multicast
Tips: For a lot of front-end network equipment, you can use a network switch to collect, when more network devices
are connected, you can choose 16-Channel Ethernet Extender Hub.
OT-PLC602 can support Power and Ethernet simultaneous transmission. When Ethernet signal transmission in
power line, to avoid power line interference, you should install Power Filter on each OT-PLC602 unit, installation
diagram as below:
Figure 5- Powerline pplication
Page 7 of 7
When you use OT-PLC602, please follow the below tips as a reference, in order to reduce the fault in the process of
using and the inspection work.
. The device supports auto-negotiation allocation master and slave. It also can be set master-slave side and grouped
by software. Each group (one point to multi-point communications group) only allows one Master, others are Slaves.
Otherwise, the network data won't be able to transmit. And Master unit should be installed in the local side.
2. Signal transmission cable must be the copper cable. Other material cables will cause the decrease of signal
transmission quality and distance.
3. Long distance cable connection must be formal connection methods, such as welding or using connectors.
4. Coaxial cable, twisted-pair cable, telephone line and power line all can be used to transmit network data signal in
projects. A variety of cables arbitrary mixed connection also can reduce the quality of signal.
5. Please choose matching power supply (12VDC / 1A).
6. If need to transmit power at the same time, you should install power filter in the front of each device to make sure
signal stability.
7. There is no waterproof design for this product, please make sure it is used in dry environment.
8. If device fails, do not disassemble or repair it by yourself. Please contact us timely.
: Specifications are subject to change without notice. Thank you for choosing us. For more details,
please visit our website: www.ourten.com
Shaoxing Ourten Electronics Co., Ltd.
3rd Floor # 7, No. 1732 Yanhua industrial park, West Renmin Road, Shangyu, Zhejiang, China
Tel: +86-21-5888 9980 (+86-575-8213 7256)
Fax: +86-575-8212 7256
www.ourten.com
