UTC Fire and Security Interlogix TruVision TVD-DOME-HR Assembly instructions

1 of 2
P/N 1069136B • REV 2.00 • ISS 04MAY11
Description
The TruVision TVD-DOME-HR camera is a high-resolution
dome camera that that can be used in retail, commercial, and
residential environments. The camera uses a varifocal lens
and offers custom configurability.
Safety precautions
Read this installation sheet in its entirety before using the
camera.
To avoid dangerous electrical shock or damage to the
equipment, do not try to disassemble the camera or any of its
components.
Do not attempt to service this camera by yourself unless you
are authorized to do so. Opening the cover may expose you to
dangerous electrical shock or other hazards. Only a service
technician should perform this procedure.
Never point the camera at the sun and do not expose the lens
directly to the sun or strong light as this may damage the
camera.
Handle the camera with care. The camera contains sensitive
components, avoid any shock or impact to the camera.
Improper handling can damage the camera.
The camera is designed for indoor use. Do not use the camera
when the temperature is lower than −10C (14°F) or higher
than +50C (122°F). For safe camera usage, the maximum
humidity should not exceed 85%. If the camera is placed in an
extremely dusty location, special housing may be needed to
protect the camera and lens.
Installation
Before installing the TruVision TVD-DOME-HR camera, make
sure that the location is mechanically sound, protects the
camera, and affords the required views. Once the camera is
securely mounted, follow the procedure below to connect the
camera. For power and video connections see Figure 1 below.
For camera dimensions see Figure 2 and Figure 3 on page 2.
Figure 1: TruVision Dome camera power and video connections
To install the camera:
1. Fasten the camera to a wall or ceiling (or another solid
surface). The camera must be stable when connected.
2. Connect the 75 Ωcoaxial cable to the video output.
3. Connect the power cable to the camera.
4. Adjust the camera position and angle as required.
Camera dimensions
Figure 2: TruVision Dome dimensions - base attachment
TruVision TVD-DOME-HR Camera
Installation Sheet

2 of 2 P/N 1069136B • REV 2.00 • ISS 04MAY11
Figure 3: TruVision dimensions - camera orientation (mm)
Maintenance
To clean inside and outside the camera, do not use any
organic or corrosive cleaning solutions. When cleaning the
camera, turn off the power, and use a clean cloth with some
water.
Specifications
Pickup device 1/3 in. interline transfer CCD
Total pixels NTSC: 811 (H) x 508 (V)
PAL: 795 (H) x 596 (V)
Effective pixels NTSC: 768 (H) x 494 (V)
PAL: 752 (H) x 582 (V)
Resolution 500 TV lines
Synchronization system Internal synchronization
Scanning system NTSC: 525 lines / 60 fields
PAL: 625 lines / 50 fields
S/N ratio >48 dB
Electronic shutter Auto 1/60 (1/50)
Minimum illumination 0.2 lux at F2.0
Video output 1.0 Vp-p, 75 Ω
White balance Automatic
Lens type Board lens / DC varifocal lens
DC power source 12 VDC, 500 mA /24 VAC,185 mA
Power consumption <2.2 W max.
Operating temperature −10 to 50°C (14 to 122°F)
FCC information
Cautions
This device complies with Part 15 FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received
including interference that may cause undesired operation.
Compliance
This Equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the service technician is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Copyright © 2011 UTC Fire & Security. All rights reserved.
Trademarks and
patents
Interlogix, TruVision brand and logo are
trademarks of UTC Fire & Security.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-
5923, USA.
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance FCC Part 15, Subpart J, Class B
European Union
directives
2004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive
2004/108/EC
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information see our Web site: www.interlogix.com.