UTEK UT-6405G-POE User manual

1 2 3
1
2
UT-6405G-POE 5 POE
5 4 PoE
IEEE 802.3af/at PD
IEEE 802.3af POE
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseT(X)
IEEE 802.3ab 1000BaseT(X)
5 RJ-45( 4 POE )
10/100/1000Base-T
LED PWR1 PWR2 FAIL RJ-45
POE
1A @ 24VDC
POE + 1 2 pins - 3 6 pins
46 57VDC 3A@48Vmax
16
IP30
\
-40 85
-40 85
0 95% ( )
EMI FCC Part 15 Subpart B classA EN55022 class A
EMS
IEC(EN)61000-4-2(ESD)
IEC(EN)61000-4-3(RS)
IEC(EN)61000-4-4(EFT)
IEC(EN)61000-4-5(Surge)
IEC(EN)61000-4-6(CS)
IEC(EN)61000-4-8
IEC 60068-2-27(Shock)
IEC 60068-2-32(Freefall)
IEC 60068-2-6(Vibration)
a. PWR1 PWR2
b. FAIL
c. RJ-45 1000 Base
10/100 Base
d. POE1 4 RJ-45 POE
5.9in5.9in
1.87in
3.93in3.93in
150.00150.00
47.6047.60
100.00100.00

1 2 3
. Installation
1.DIN-Rail
Tighten the rail to the device by screws
Push the bottom of the device rail to fixed rail.
Then push it into the rail slightly again
2. Wall Mounted
Tighten the metal fixation strip with screws as shown above.
Then hang the machine with locked metal strip on the wall
or machine cabinet.
UT-6405G-POE
10/100/1000M 5-Port Industrial POE Switch
User Manual
.Overview
UT-6405G-POE isa 5-port industrial grade unmanaged POE Gigabit
Ethernet switch with reverse polarity protection ofAC or DC input for
avoiding being standard snap-fit-mounting and wall-mounting installation,
so it's very easy to be installedand used in any industrial networks.
. Main Features
Standards:
Port:
Ethernet Port: 5x10/100/1000Base-TXRJ-45 ports(POE output)
Alarm co ntact: 1 c hannel relay output, NO NC capacity1A@ 24VDC
POE Power: +(1,2) pins; -(3, 6) pins
Power requirement:
Voltage Input : 46-57VDC, redundant dualpower input, 1A@24VDC
Terminal Block:1 pluggable 6-pin
Overload protection: Yes
Reverse Polarity Protection:Yes
Characteristics:
IP Rating:IP30
Installation: DIN-Rail/wall mounted
Environment:
Operating Temperature:
Storage Temperature:
Relative Humidity: 0%-95%(Non-condensing)
Industrial Standards:
IEEE 802.3af/at POE
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseT(X)
IEEE 802.3ab 1000BaseT(X)
-40 85
-40 85
EMI FCC Part 15Subpart B classA EN55022 classA
EMS
IEC(EN)61000-4-2(ESD)
IEC(EN)61000-4-3(RS)
IEC(EN)61000-4-4(EFT)
IEC(EN)61000-4-5(Surge)
IEC(EN)61000-4-6(CS)
IEC(EN)61000-4-8
IEC 60068-2-27(Shock)
IEC 60068-2-32(Freefall)
IEC 60068-2-6(Vibration)
. Dimension
. Indicator
a. PWR1, PWR2 on, it shows the power is on and normal
b. FAIL indicator on, it shows the power is break down or one
channel is disconnected
c. a.RJ-45: when access to Internet, green indicator on the left will be
on under 100 Base, but not for 10 Base; the yellow indicator on the
right indicates network data communication, when the device access
to Internet, yellow indicator is blinking; without access to Internet,
yellow and green indicators will not on.
d. POE1-8 indicators will be on when RJ-45 ports provides with POE output
. Power Connection
Industrial Ethernet switch supports 46-57V DC input, and it is with
reverse polarity protection.
a. Connect the positive/negative polarity to V+ and V-terminals
respectively
b.Tighten the screw to avoid bad connection Both side of is
for power alarm signal output, when the power is breakdown, or
1 channel is without power on, it will be alarmed.
5.9in5.9in
1.87in
3.93in3.93in
150.00150.00
47.6047.60
100.00100.00