VADO Omika OMI-300-CP User manual

Mono Basin Mixer
OMI-300-CP
OMIKA
Keep for future reference
Installation Guide
where inspiration flows
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com
This instruction booklet covers model:
OMI-300-CP
Version 1, 1-10-19

23
Please read these instructions carefully before starting installation and keep for
future reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
Important - please read
Operating Specifications
Operating Pressure
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
General installation
This fitting is a mixing device and therefore water supplies should be reasonably
balanced.
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email ([e-mail]) or telephone: [phone].
Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed
to remove debris. Failure to do so could result in damage or low flow from the mixer
unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Contents of Packaging
Installation guide &
User manual
Mixer
with base ring and O-ring
Fixing Kit
Flexible hoses Threaded rod Nut
Mono Basin Mixer
OMI-300-CP
OMIKA
Installation Guide
WHERE
INSPIRATION
FLOWS
OMIKA
Mono Basin Mixer
1
5
y
e
a
r
g
u
a
r
a
n
t
e
e
User Guide
Keep for fut ure reference
Metal/rubber washer

4 5
12
Valve dimensions Installation - Quick guide
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
2
1
5
4
6
3
60mm
33mm162mm
48mm
75mm
102mm
153mm

6 7
Notes:Installation
Before installing your new mixer, flush
through the pipe work to ensure removal
of debris, turn off the water supply.
Place the base ring onto the bottom of the
mixer make sure the O-ring is in place in
the underside of the base ring.
Position the mixer on the basin. From
the underside of the basin screw the
two flexible pipes to the hot and cold
connections in the mixer body, the hot
should be to the left and the cold to the
right, hand tighten only.
Screw the threaded rod into the small
hole inside the mixer body.
Slide the rubber/metal washer over the
rod, the rubber washer should be on top.
Screw on the nut and tighten to clamp the
mixer to the basin.
CAUTION: Do not over tighten the nut as
this may damage the basin.
Connect the water supply to the inlet
pipes. The hot water should be connected
to the left pipe and cold to the right.
CAUTION: When
installing the
flexible hoses do
not kink, or bend
them more than the
60mm diameter as
shown right.
60mm
Control
handle
O-ring
Base ring
Rubber/
metal
washer
Nut
Hot flexible
pipe (red)
Cold flexible
pipe (blue)
Threaded
rod