VADO SYNERGIE SYN-100 User manual

Mono Basin Mixers
100
100E
SYNERGIE
Keep for future reference
Installation Guide
where inspiration flows
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com
This instruction booklet covers models:
SYN-100 & SYN-100E.
Version 1, 1-9-17

23
Please read these instructions carefully before starting installation and keep for
future reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
General installation
Operating Specifications
Important - please read
Operating Pressure
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
This fitting is a mixing device and therefore water supplies should be reasonably
balanced.
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email ([e-mail]) or telephone: [phone].
Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed
to remove debris. Failure to do so could result in damage or low flow from the mixer
unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Contents of Packaging
Valve body 100 or 100E
(100 shown)
Mono Basin Mixers
100
1000E
SYNERGIE
Keep for future reference
Installation Guide
SYNERGIE
Mono Basin Mixer
User Guide
Keep for fut ure reference
WHERE
INSPIRATION
FLOWS
Installation guide &
User manual
(100 shown) Flexible hoses
(Red for hot,
Blue for cold)
Metal washer
Hex key
Fixing kit box
(Nuts, Threaded rods, Base seal,
Rubber washer, Metal washer & Hex key)
FIXING KIT BOX
Rubber washer
Base seal
Threaded rods
(100 shown)
(100E 2 x short)
Nuts

4 5
Valve dimensions - 100
38mm
73mm
139mm 46mm
G1/2
88mm
110mm
130mm
Valve dimensions - 100E
38mm
73mm
199mm 46mm
G1/2
88mm
270mm
290mm

7
6
Installation
NOTE: For illustrative purposes only
the 100 tap installation is shown.
Please follow the same procedure to
install the 100E tap.
Before installing your new mixer, flush
through the pipework to ensure removal
of debris, turn off the water supply.
Place the seal in the slot on the
underside of the mixer body.
Position the mixer on the basin. From
the underside of the basin screw the
two flexible pipes to the hot and cold
connections in the mixer body, the hot
should be to the front and the cold to
the back, hand tighten only.
Screw the two threaded rods into the
body the short rod to the front and long
at the back. Both rods are the same for
the 100E.
Clip together the rubber and metal
washers and slide over the rods, the
rubber washer should be on top. Screw
on the nuts and tighten to clamp the
mixer to the basin.
CAUTION: Do not over tighten the nuts
as this may damage the basin.
Connect the water supply to the
inlet pipes. The hot water should be
connected to the front pipe and cold to
the back.
60mm
Installation - Quick guide
1
2
3
Max - 5 Bar
1
2 3
4
0 5
Min - 1 Bar
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
3
1
4
5
6
7
2
Rubber
washer
Metal
washer
Hot flexible
hose (red)
Cold flexible
hose (blue)
Seal
Threaded
rods
Nuts