Vanguard 1111AML User manual

Operation Manual
Covering Models:
1111AML, 1112AML,
1113AML & 1115AML
1100AML Series

Eyepieces
Head
Diopter
Adjustment
Mechanism
Nosepiece
Objectives
Mechanical Stage
X-Y Controls
Condenser
Iris Diaphragm
Adjustment Lever
Coarse Focus
Control
1100AML Series Parts
Base
Stand
Mechanical
Stage
Slide Holder
Mechanical Stage
Release Knob
Fine Focus
Control
Substage
Illuminator
ON/OFF
Power
Switch
Diopter
Adjustment
Mechanism
Variable
Illumination
Control
Head Set Screw
Swing-In
Dispersion
Filter
2

Thank you for purchasing a VanGuard Microscope. With the user in mind, VanGuard Microscopes are built from
modern designs and should provide a lifetime of reliable performance. We recommend you read this entire manual
carefully before beginning to use the instrument.
Warranty information and a registration card can be found at the following web address. We encourage you to ll
this out and send in so that we have a record in case you should need to receive technical support in the future.
www.veegee.com/pages/technical-support-service
Assembly
Lighting and Power
1
2
3
4
5
1
2
General Operation
3
Focusing and Mechanical Stage Mechanisms
1
2
3
Interpupillary and Diopter Adjustment
1
2
3
Interpupillary adjustment (the distance between eyepieces) is made through a “sliding” action. Slide the eye-
pieces until they are the proper distance apart for comfortable use.
Diopter adjustment allows for proper optical correction based on each individual’s eyesight. This adjustment
is easily made and is recommended prior to use.
Using the 40X objective and a sample slide (i.e. one which produces an easily focused image), close your left
eye and bring the image into focus in your right eye with the coarse and ne focus controls. Once the image
is well-focused using only your right eye, close your right eye and check the focus with your left. If the image
is not perfectly focused, make ne adjustments with the diopter adjustment mechansim located on the left
eyetube. Once complete, the microscope is corrected for your vision.
Focusing adjustment is achieved by turning the coarse and ne focus control knobs. The large knob is used
for coarse adjustment, while the smaller knob is used for ne adjustment. Focusing tension can be adjusted
by turning the focus tension adjustment ring located just inside of the left coarse focus control knob.
To ensure long life, always turn the focusing knobs slowly and uniformly.
The mechanical stage X-Y controls provide easy and accurate positioning of the sample.
Connect the power plug to a suitable power supply; turn on substage illuminator with the ON/OFF switch
located on the right side of the base.
The VanGuard 1100AML Series microscopes incorporate an internal LED light source for long life and low
power consumption. The LED illuminator is designed to last the life of the instrument therefore replacement
of the lamp is unnessesary.
After removing the microscope parts from the protective foam packaging and checking it over for all components
and accessories, you can begin assembly.
Place the stand on a stable surface.
Place the head on top of the stand so that the dovetail ange slides into place. Secure with the knurled head
set screw. NOTE: Do not release the head until it is rmly secured with the head set screw.
Slide the eyepieces into the eyetubes.
After removing the objectives from their storage containers, individually install each one into the nosepiece
by twisting them clockwise into the threaded holes of the nosepiece.

General Operation
Substage Adjustments
Adjustments to the substage condenser are crucial for proper illumination and performance. There are three basic
adjustments which need to be made: Centering, Vertical Focusing, and Aperture Adjustment. Also, the condenser
features a swing-in dispersion lter to cut down on excessive lamp glare should it be necessary.
Centering:
The condenser is factory-centered and xed and therefore does not require any centering adjustments.
Vertical Focusing:
The condenser can be raised and lowered with the condenser adjustment lever to focus the light for optimal illumination.
Aperture Adjustment:
The light path can be adjusted with the iris diaphragm adjustment lever located just below the condenser. Aperture
adjustments are made to induce contrast into a specimen, not to adjust light intensity.
1
2
3
Model 1111AML
Monocular Head (1 ea.)
Stand (1 ea.)
Brighteld Condenser (1 ea.)
10X Eyepiece (1 ea.)
4X Achromatic Objective (1 ea.)
10X Achromatic Objective (1 ea.)
40X Achromatic Objective (1 ea.)
100X Achromatic Objective (1 ea.)
Model 1113AML
Binocular Head (1 ea.)
Stand (1 ea.)
Brighteld Condenser (1 ea.)
10X Eyepiece (2 ea.)
4X Achromatic Objective (1 ea.)
10X Achromatic Objective (1 ea.)
40X Achromatic Objective (1 ea.)
100X Achromatic Objective (1 ea.)
Model 1115AML
Trinocular Head (1 ea.)
Stand (1 ea.)
Brighteld Condenser (1 ea.)
10X Eyepiece (2 ea.)
4X Achromatic Objective (1 ea.)
10X Achromatic Objective (1 ea.)
40X Achromatic Objective (1 ea.)
100X Achromatic Objective (1 ea.)
Note on Oil Immersion Objectives
The 100X objective which comes with this microscope must be used with immersion oil in order to maintain
image quality. After use, the objective tip needs to be wiped clean so that no oil residue remains. Under no cir-
cumstances should an oil immersion objective be left sitting in oil for an extended period of time. Exceptionally
long immersion periods can cause oil to penetrate the objective’s sealant and obscure the optics, which is not
covered under warranty.
Printed in the USA No. VGMNL070319-1100AML
Maintenance
The eyepiece and objective lenses on VanGuard Microscopes contain a special optical surface coating and
therefore should never be wiped while dry as any dirt or dust will scratch the coating.
The surfaces should either be blown off with an air canister, or blown and cleaned with an air-bulb and camel-hair
brush. It is recommended to then use a lens cleaner. Apply with a cotton swab for a minimum of wetting, then
wipe the surface clean with a quality lens tissue. Xylene, since it breaks down the bonding material holding the
lenses, should never be used as a cleaner.
Periodically your VanGuard Microscope should be fully serviced by a qualied service technician.
For information about parts, accessories, or service -- contact your dealer directly or contact VanGuard
Microscopes at 1-800-423-8842.
Model 1112AML
Dual Monocular Head (1 ea.)
Stand (1 ea.)
Brighteld Condenser (1 ea.)
10X Eyepiece (2 ea.)
4X Achromatic Objective (1 ea.)
10X Achromatic Objective (1 ea.)
40X Achromatic Objective (1 ea.)
100X Achromatic Objective (1 ea.)
4