VARO POWERplus GardenPro POWXG3025 User manual

POWXG3025 EN
Copyright © 2015 VARO P a g e | 1www.varo.com
1APPLICATION ...................................................................................3
2DESCRIPTION (FIG. A).....................................................................3
3PACKAGE CONTENT LIST ..............................................................3
4SYMBOLS..........................................................................................4
5GENERAL SAFETY WARNINGS......................................................5
5.1 Work area ..................................................................................................................5
5.2 Personal safety .........................................................................................................5
5.3 Engine tool use and care..........................................................................................5
5.4 Service.......................................................................................................................6
6ADDITIONAL SAFETY INSTRUCTIONS FOR PETROL HEDGE
TRIMMERS.........................................................................................6
7SAFETY WARNINGS GASOLINE ....................................................6
8MACHINE′S SAFETY EQUIPMENT..................................................6
8.1 Throttle lockout.........................................................................................................7
8.2 Engine switch (Fig. 6) ...............................................................................................7
8.3 Vibration damping system (Fig. 7)...........................................................................7
8.4 Quick release.............................................................................................................7
8.5 Muffler........................................................................................................................7
9CUTTING EQUIPMENT (CUTTING ATTACHMENT & GRASS
TRIMMER)..........................................................................................8
9.1 Cutting attachment ...................................................................................................8
9.2 Sharpening grass cutters and grass blades ...........................................................8
9.3 Trimmer head............................................................................................................8
10 CUTTING EQUIPMENT (LONG REACH HEDGE TRIMMER)..........9
11 OPERATING INSTRUCTIONS..........................................................9
11.1 Prepare the machine.................................................................................................9
11.1.1 Assembling the Front handle.......................................................................................9
11.1.2 Connecting the tube (Fig. 12)......................................................................................9
11.1.3 Fitting blades and trimmer heads ................................................................................9
11.1.4 Fitting the guard extension..........................................................................................9

POWXG3025 EN
Copyright © 2015 VARO P a g e | 2www.varo.com
11.1.5 Fitting a blade guard, grass blade and grass cutter...................................................10
11.1.6 Fitting the trimmer guard and trimmer head (Fig. 18).................................................10
11.1.7 Fitting cutting head (Hedge trimmer) (Fig. 19)...........................................................10
11.1.8 Adjusting the harness (Fig. 20)..................................................................................10
11.2 Fuel handling...........................................................................................................11
11.2.1 Fuel safety................................................................................................................11
11.2.2 Transport and storage...............................................................................................11
11.2.3 Fuel...........................................................................................................................11
11.2.4 Petrol........................................................................................................................11
11.2.5 Two-stroke oil............................................................................................................12
11.2.6 Mixing .......................................................................................................................12
11.2.7 Fuelling.....................................................................................................................12
11.3 Using the machine..................................................................................................12
11.3.1 Check and starting....................................................................................................12
11.3.2 Starting and stopping................................................................................................13
11.4 General working instructions.................................................................................14
11.4.1 Basic working techniques..........................................................................................14
11.4.2 Grass clearing using a grass blade ...........................................................................15
11.4.3 Grass trimming with a trimmer head..........................................................................15
11.4.4 Trimming branch or leaves with Long-reach hedge trimmer......................................16
11.5 Routine maintenance..............................................................................................16
11.5.1 Air filter......................................................................................................................16
11.5.2 Fuel filter (Fig. 36).....................................................................................................16
11.5.3 Spark plug.................................................................................................................16
12 MAINTENANCE TIMESCALE.........................................................17
13 TECHNICAL DATA..........................................................................18
14 NOISE...............................................................................................19
15 TROUBLESHOOTING.....................................................................19
16 WARRANTY.....................................................................................20
17 ENVIRONMENT...............................................................................20

POWXG3025 EN
Copyright © 2015 VARO P a g e | 3www.varo.com
LONG REACH 3-IN-1 COMBI: BRUSH CUTTER, GRASS
TRIMMER, HEDGE TRIMMER 33CC
POWXG3025
1 APPLICATION
This appliance is designed for the following applications:
Brush cutter (when fitted with metal circular blade): The brush cutter is intended to cut
weed and climbing plants. Do not use it for other purposes, never use it for
cutting wood. Never cut objects with a diameter exceeding 13 mm.
Grass trimmer (when fitted with nylon line cutting head): The grass trimmer is intended for
trimming grass. Do not use it for other purposes.
Hedge trimmer (when fitted with reciprocating blade): The trimmer is intended to be used
for trimming hedges and bushes with diameter not more than 24 mm.
Do not use this appliance for other purpose than those described in this manual.
WARNING! Read this manual and general safety instructions carefully
before using the appliance, for your own safety. Your tool should only be
passed on together with these instructions.
2 DESCRIPTION (FIG. A)
1. Trimmer head
2. Top protecting cap
3. Gear box
4. Fixing plate
5. Cutting attachment guard
6. Front drive shaft tube
7. Lock pin
8. Lock knob
9. Connector
10. Barrier
11. Front handle
12. Rear drive shaft tube
13. Engine switch
14. Throttle lock
15. Throttle trigger lockout
16. Auxiliary handle
17. Suspension ring
18. Output flange
19. Spark plug
20. Engine
21. Starter handle
22. Fuel tank
23. Choke knob
24. Primer bulb
25. Filter cover
26. Throttle trigger
27. Locking nut
28. Bottom Protecting cap
29. Bottom clamping plate
30. Metal blade
31. Top clamping plate
32. Carrying belt
33. Blade cover
34. Cutting blade
35. Grease nozzle
36. Transmission
37. Locking lever
38. Grip
39. Safety lever
40. Gear box
3 PACKAGE CONTENT LIST
Remove all packing materials
Remove remaining packaging and transit supports (if existing)
Check the completeness of the packing content
Check the appliance, the power cord, the power plug and all accessories for transportation
damages.
Keep the packaging materials as far as possible till the end of the warranty period.
Dispose it into your local waste disposal system afterwards.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 4www.varo.com
WARNING Packing materials are no toys! Children must not play with
plastic bags! Danger of suffocation!
LONG REACH 3-in-1 combi: brush cutter, grass trimmer, hedge trimmer 33Cc
Safety blade cover
Carrying belt
Manual
Spark plug wrench
When parts are missing or damaged, please contact your dealer.
4 SYMBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal injury or damage to the tool.
Read instructions carefully
Wear safety glasses and ear protection
Wear gloves
Wearing of protective shoes advised
Never operate the machine in the rain or in damp or wet condition. Moisture
is a shock hazard.
Warning! Flying objects
Don’t use the trimmer in any position that causes any part to come within 10m
of overhead electrical line
Keep hands away from blades, Don’t touch the blades when starting or while
operating the unit.
Keep a minimum distance of 15m between the machine and third parties
during use
Extremely hot surface. Do not touch a hot muffler, gear box or cylinder. You
may get burned. These parts get extremely hot from operation and remain hot
a short time after the unit is turned off.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 5www.varo.com
5 GENERAL SAFETY WARNINGS
Read all safety warnings and all instructions. Failure to follow all warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
5.1 Work area
Keep work area clean and well lit. Cluttered and dark areas invite accidents.
Do not operate tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a tool. Distractions can cause you to
lose control.
5.2 Personal safety
Stay alert, watch what you are doing and use common sense when operating a tool. Do
not use a tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating tools may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used whenever conditions require
will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have the switch on
invites accidents.
Remove any adjusting key or wrench before turning the tool on. A wrench or a key left
attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or long hair can be caught in moving
parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of these devices can reduce dust related
hazards.
5.3 Engine tool use and care
Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it was designed.
Store idle tools out of the reach of children and do not allow persons unfamiliar with the
tool or these instructions to operate the tool. The tools are dangerous in the hands of
untrained users.
Maintain tools. Check for misalignment or sticking of moving parts, breakage of parts and
any other condition that may affect the tool’s operation. If damaged, have the tool repaired
before use. Many accidents are caused by poorly maintained tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to stick and are easier to control.
Use the tool, accessories and tool bits etc., in accordance with these instructions and in
the manner intended for the particular type of tool, taking into account the working
conditions and the work to be performed. Use of the tool for operations different from
intended could lead to a hazardous situation.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 6www.varo.com
5.4 Service
Have your tool serviced by a qualified person using only identical replacement parts. This
will ensure that the safety of the tool is maintained.
6 ADDITIONAL SAFETY INSTRUCTIONS FOR PETROL HEDGE
TRIMMERS
Do not operate in a hazardous location. Such areas include where there is a risk of
explosion of petrol fumes, leaking gas or explosive dust.
Do not operate in a confined area. Exhaust gases, smoke or fumes could reach
dangerous concentrations.
Protect your tool. This hedge trimmer is NOT WEATHERPROOF and should not be
exposed to direct sunlight, high ambient temperature and damp, wet or high humidity
conditions.
Do not smoke while refueling. This is potentially dangerous as it may ignite the fuel and
cause an explosion.
Take care not to spill fuel. When refueling the hedge trimmer ensure that the motor has
been switched off. Prevent the spilling of fuel as this may also ignite with the hot motor.
Never refuel whilst the engine running.
Be careful where you store the hedge trimmer. Store the hedge trimmer in a dry area
away from flammable liquids.
Keep your distance. The hedge trimmer emits exhaust fumes. Ensure bystanders keep a
safe distance.
Ensure you use oil-mix fuel. Ensure that you mix 40 parts unleaded fuel to 1 part 2-stroke
oil. If not, the engine will overheat and cause damage to your hedge trimmer.
7 SAFETY WARNINGS GASOLINE
WARNING: Use extra care in handling fuels. They are flammable and the
vapours are explosive. The following points must be observed.
Use only an approved container.
Never remove the fuel cap or add fuel with the power source running. Allow engine
exhaust components to cool before refueling.
Do not smoke.
Never refuel the machine indoors.
Never store the machine or fuel containers inside, where is an open flame, such as a
water heater.
If fuel is spilled, do not attempt to start the power source, but move the machine away
from the area of spillage before starting.
Always replace and securely tighten the fuel cap after refueling.
If the tank is drained, this should be done outdoors.
8 MACHINE′S SAFETY EQUIPMENT
WARNING! Never use a machine with faulty safety equipment. The
machine’s safety equipment must be checked and maintained as described
in this section. If your machine fails any of these checks contact your
service agent to get it repaired.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 7www.varo.com
8.1 Throttle lockout
The throttle lockout is designed to prevent accidental operation of the throttle control.
When you press the lock-out (A) (i.e. when you grasp the handle) it releases the throttle
trigger (B). When you release the handle the throttle control and the throttle lockout both
move back to their original positions. This movement is controlled by two independent
return springs. This arrangement means that the throttle control is automatically locked at
the idle setting. (Fig. 1)
Make sure the throttle control is locked at the idle setting when (Fig. 2)
Press the throttle lockout and make sure it returns to its original position when you release
it. (Fig. 3)
Check that the throttle control and throttle lockout move freely and that the return springs
work properly. (Fig. 4)
See instructions under the heading Start. Start the machine and apply full throttle. Release
the throttle and check that the cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position then the carburetor idle
setting must be checked. (Fig. 5)
8.2 Engine switch (Fig. 6)
Press down the “O” side of the engine switch to stop the engine.
Start the engine and make sure the engine stops when you move the engine switch to the stop
setting.
8.3 Vibration damping system (Fig. 7)
Your machine is equipped with a vibration damping system that is designed to minimize
vibration and make operation easier.
Using incorrectly wound cord or a blunt or incorrect cutting attachment (wrong type or
incorrectly filed, see instructions under the heading Filing the blade) increases the level of
vibration.
The machine′s vibration damping system reduces the transfer of vibration between the engine
unit/cutting equipment and the machine′s handle unit.
Regularly check the vibration damping units for cracks or deformation.
Check that the vibration damping element is undamaged and securely attached.
8.4 Quick release
There is an easily accessible, quick release fitted near the suspension ring as a safety
precaution in case the engine catches fire, or in any other situation that requires you to free
yourself from the machine.
8.5 Muffler
The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away
from the user.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to the machine.
The inside of the muffler contain chemicals that may be carcinogenic. Avoid
contact with these elements in the event of a damaged muffler.
Bear in mind that: The exhaust fumes from the engine are hot and may
contain sparks which can start a fire. Never start the machine indoors or
near combustible material!

POWXG3025 EN
Copyright © 2015 VARO P a g e | 8www.varo.com
9 CUTTING EQUIPMENT (CUTTING ATTACHMENT & GRASS
TRIMMER)
This section describes how to choose and maintain your cutting equipment in order to:
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
IMPORTANT: Only use cutting attachments with the guards we recommend! See the chapter
on Technical data. Refer to the instructions for the cutting attachment to check the correct way
to load the cord and the correct cord diameter.
Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to
the instructions on the blade packaging.
Always stop the engine before doing any work on the cutting attachment.
This continues to rotate even after the throttle has been released. Ensure
that the cutting attachment has stopped completely and disconnect the HT
lead from the spark plug before you start to work on it. Using an incorrect
cutting attachment or an incorrectly sharpened blade increases the risk of
blade thrust.
9.1 Cutting attachment
Grass blades and grass cutters are intended for cutting coarse grass. (Fig. 8)
A trimmer head is intended for trimming grass. (Fig. 9)
General rules
Only use cutting attachments with the guards we recommend! See the chapter on
Technical data.
Keep the teeth of the blade correctly sharpened! Follow our instructions and use the
recommended file gauge. An incorrectly sharpened or damaged blade increases the risk
of accidents.
Check the cutting attachment for damage or cracks. A damaged cutting attachment should
always be replaced.
9.2 Sharpening grass cutters and grass blades
Sharpen blades and cutters using a single-cut flat file.
Sharpen all edges equally to maintain the balance of the blade.
Always discard a blade that is bent, twisted, cracked, broken or damaged in
any other way. Never attempt to straighten a twisted blade so that it can be
reused. Only use original blades of the specified type.
9.3 Trimmer head
IMPORTANT: Always ensure the trimmer cord is wound tightly and evenly around the drum,
otherwise the machine will generate harmful vibration.
Only use the recommended trimmer heads and trimmer cords. These have been tested by the
manufacturer to suit a particular engine size. This is especially important when a fully
automatic trimmer head is used. Only use the recommended cutting attachment. See the
chapter on Technical data.
Smaller machines generally require small trimmer heads and vice versa. This is because
when clearing using a cord the engine must throw out the cord radially from the trimmer head
and overcome the resistance of the grass being cleared.
The length of the cord is also important. A longer cord requires greater engine power than a
shorter cord of the same diameter.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 9www.varo.com
Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the
correct length.
To increase the life of the cord it can be soaked in water for a couple of days. This will make
the line tougher so that it lasts longer.
10 CUTTING EQUIPMENT (LONG REACH HEDGE TRIMMER)
To ensure good cutting results it is important that the contact pressure between the blades is
correct. The contact pressure is adjusted by turning the screws on the underside of the bar
clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn. Lock the
screws using the locking nut on the top of the bar. Check that the screws are loose enough to
allow the washers under the screw heads to slide sideways.
When the blades are correctly adjusted the play between the blades should be 0,2–0,4 mm,
measured at the screws.
The edges of the blades are too hard to be filed. Dull blades should be sharpened using a
grinder.
Replace the blades if they are bent or damaged.
11 OPERATING INSTRUCTIONS
11.1 Prepare the machine
11.1.1 Assembling the Front handle
Fit the front handle absorber (A) on the rear tube (C). While aligning the hole (B) on the front
handle absorber、the position pin (F) on the barrier (E) and one position hole (D) of three on
the rear handle, fit the barrier on the rear handle and insert the position pin into the position
hole on the rear handle. Make sure the barrier on the left side of the machine. (Fig. 10)
Push down the front handle (G), and then turn four screws (H) clockwise to tighten the front
handle securely. (Fig. 11)
11.1.2 Connecting the tube (Fig. 12)
Align the hole (A1) on the front tube (A) and the lock pin (B). Then, Pull out the Lock pin, and
while inserting the front tube in the connector (D) to the end. After loosened the lock pin, it will
return to its original position automatically, and insert into the hole on the front tube.
Make sure the front tube can’t be rotated after the lock pin came back to its original position.
Turn the lock knob (C) clockwise to tighten the front tube securely.
11.1.3 Fitting blades and trimmer heads
When fitting the cutting attachment it is extremely important that the raised
section on the top clamping plate/support flange engages correctly in the
centre hole of the cutting attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or fatal personal injury.
Never use a cutting attachment without an approved guard. See the chapter
on Technical data. If an incorrect or faulty guard is fitted this can cause
serious personal injury.
11.1.4 Fitting the guard extension
The guard extension shall always be fitted when using the trimmer head and combination
guard. The guard extension shall always be removed when using the grass blade. (Fig.
13)

POWXG3025 EN
Copyright © 2015 VARO P a g e | 10 www.varo.com
Hook the blade guard/combination guard onto the fitting on the shaft and secure with three
bolts. (Fig. 13)
Enter the guard extension guide in the slot of the combination guard. Then click the guard
extension into position on the guard with some claws. (Fig. 14)
The guard extension is removed easily using a screwdriver, see illustration. (Fig. 15)
11.1.5 Fitting a blade guard, grass blade and grass cutter
Hook the blade guard/combination guard onto the fitting on the shaft and secure with three
bolts. Use the recommended blade guard. See the Technical data section. (Fig. 16)
CAUTION! Ensure that the guard extension is removed.
Fit the top clamping plate (B) on the output shaft.
Turn the blade shaft until one of the holes in the top clamping plate aligns with the
corresponding hole in the top protecting cap.
Insert the locking pin (A) in the hole to lock the shaft.
Place the blade (C), bottom clamping plate (D) and bottom protecting cap (E) on the
output shaft. (Fig. 17)
Fit the nut (F). The nut must be tightened to a torque of 35-50 Nm. Use the socket
spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as
possible. To tighten the nut, turn the spanner in the opposite direction to the direction of
rotation (Caution! left-hand thread).
Pull out the locking pin after all installation process has been finished.
11.1.6 Fitting the trimmer guard and trimmer head (Fig. 18)
Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with
three bolts.
Fit the top clamping plate (B) on the output shaft.
Turn the blade shaft until one of the holes in the top clamping plate aligns with the
corresponding hole in the top protecting cap (C).
Insert the locking pin (A) in the hole to lock the shaft.
Screw on the trimmer head (D) in the opposite direction to the direction of rotation.
To dismantle, follow the instructions in the reverse order.
11.1.7 Fitting cutting head (Hedge trimmer) (Fig. 19)
Fit the cutting head (B) on the shaft tube (A) so that the screw hole on the cutting head is
aligned with the position hole (A1) on the shaft tube as shown. Then, tighten the lock screw (D)
and the position screw (C) securely.
Changing the hedge trimmer angle
Press the safety lever (E). Then press the lock lever (F), at the same time hold the grip (G)
and turn the cutting head to a desired angle (α).
11.1.8 Adjusting the harness (Fig. 20)
WARNING! When using the machine it must always be hooked securely to
the harness. Otherwise you will be unable to control the brush cutter safely
and this can result in injury to yourself or others. Never use a harness with
a defective quick release.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 11 www.varo.com
Single shoulder harness: Put on the harness. Hook the machine onto the harness support
hook. Adjust the length of the harness so that the support hook is roughly level with your right
hip.
11.2 Fuel handling
11.2.1 Fuel safety
Never start the machine:
If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.
If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of
your body that has come in contact with fuel. Use soap and water.
If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.
11.2.2 Transport and storage
Store and transport the machine and fuel so that there is no risk of any leakage or fumes
coming into contact with sparks or naked flames, for example, from electrical machinery,
electric motors, electrical relays/ switches or boilers.
When storing and transporting fuel always use approved containers intended for this
purpose.
When storing the machine for long periods the fuel tank must be emptied. Contact your
local petrol station to find out where to dispose of excess fuel.
Ensure the machine is cleaned and that a complete service is carried out before long-term
storage.
The transport guard must always be fitted to the cutting attachment when the machine is
being transported or in storage.
Secure the machine during transport.
In order to prevent unintentional starting of the engine, the spark plug cap must always be
removed during long-term storage, if the machine is not under close supervision and when
performing all service measures.
Take care when handling fuel. Bear in mind the risk of fire, explosion and
inhaling fumes.
11.2.3 Fuel
The machine is equipped with a two-stroke engine and must always been run using a mixture
of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed
to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
Fuel and fuel fumes are highly inflammable and can cause serious injury
when inhaled or allowed to come in contact with the skin. For this reason
observe caution when handling fuel and make sure there is adequate
ventilation.
11.2.4 Petrol
Always use a quality petrol/oil mixture at least 90 octane (RON). If your machine is equipped
with a catalytic converter (see chapter on Technical data) always use a good quality unleaded
petrol/oil mixture. Leaded petrol will destroy the catalytic converter.
Use low-emission petrol, also known as alkylate petrol, if it is available.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 12 www.varo.com
The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade
than 90 so- called knocking can occur. This gives rise to a high engine temperature, which can
result in serious engine damage.
When working at continuous high revs a higher octane rating is recommended.
11.2.5 Two-stroke oil
For best results and performance use two-stroke engine oil, which is specially formulated for
our air-cooled two-stroke engines.
Never use two-stroke oil intended for water-cooled engines, sometimes referred to as
outboard oil (rated TCW).
Never use oil intended for four-stroke engines.
A poor oil quality and/or too high oil/fuel ratio may jeopardize function and decrease the life
time of catalytic converters.
11.2.6 Mixing
Always mix the petrol and oil in a clean container intended for fuel.
Always start by filling half the amount of the petrol to be used. Then add the entire amount
of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.
Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.
Do not mix more than one month’s supply of fuel at a time.
If the machine is not used for some time the fuel tank should be emptied and cleaned.
11.2.7 Fuelling
Taking the following precautions, will lessen the risk of fire:
Do not smoke or place hot objects near fuel.
Always shut off the engine before refueling.
Always stop the engine and let it cool for a few minutes before refueling.
When refueling, open the fuel cap slowly so that any excess pressure is released gently.
Tighten the fuel cap carefully after refueling.
Always move the machine away from the refueling area before starting.
Always use a fuel container with an anti-spill valve.
Clean the area around the fuel cap. Contamination in the tank can cause operating
problems.
Ensure that the fuel is well mixed by shaking the container before filling the tank.
11.3 Using the machine
11.3.1 Check and starting
Never use the machine without a guard nor with a defective guard.
All covers must be correctly fitted and undamaged before you start the machine.
Petrol, litre
Two-stroke oil, millilitre
2.5% (1:40)
1
25
5
125
10
250
20
500

POWXG3025 EN
Copyright © 2015 VARO P a g e | 13 www.varo.com
Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the
centre hole. The most common reason why cracks are formed is that sharp corners have
been formed at the bottom of the teeth while sharpening or that the blade has been used
with dull teeth. Discard a blade if cracks are found.
Check that the support flange is not cracked due to fatigue or due to being tightened too
much. Discard the support flange if it is cracked.
Ensure the locking nut has not lost its captive force. The nut lock should have a locking
force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.
Check that the blade guard is not damaged or cracked. Replace the blade guard if it is
exposed to impact or is cracked.
Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the
trimmer head or trimmer guard if they have been exposed to impact or are cracked.
11.3.2 Starting and stopping
The complete clutch cover and shaft must be fitted before the machine is started, otherwise
the clutch can come loose and cause personal injury.
Always move the machine away from the refueling area before starting. Place the machine on
a flat surface. Ensure the cutting attachment cannot come into contact with any object.
Make sure no unauthorized persons are in the working area, otherwise there is a risk of
serious personal injury. The safety distance is 15 metres.
11.3.2.1 Cold starting:
A “cold” start of the engine means starting it after at least 5 minutes from when it was switched
off or after refueling.
Starting: Ignition: Press down the “I” side of the engine switch. (Fig. 21)
Primer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb. The bulb
need not be completely filled. (Fig. 22)
Choke: Set the choke knob in the choke position. (Fig. 23)
Throttle lock button: When pressing throttle trigger lock-out and throttle trigger, press the
throttle lock button simultaneously, and then release throttle trigger and throttle trigger
lock-out. (Fig. 24)
The throttle lock will automatically release by pressing the throttle trigger
again. If you manually turn the choke knob from choke position to run
position before releasing the throttle lock button, the cutting attachment
will start to rotate immediately when the engine is started.
Hold the body of the machine on the ground using your left hand (CAUTION! Not with your
foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel
some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never
twist the starter cord around your hand. Repeat pulling the cord until engine firing occur.
(Fig. 25)
Choke: Set the choke knob in the open position. (Fig. 26)
Repeat pulling the cord until engine start. When the engine starts, allow the engine to
warm up with the throttle lock engaged. Then, pressing throttle trigger to release the
throttle lock. (Fig. 27)
Do not pull the starter cord all the way out and do not let go of the starter handle when the
cord is fully extended. This can damage the machine.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 14 www.varo.com
Do not put any part of your body in marked area. Contact can result in burns to the skin, or
electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a
machine with damaged spark plug cap.
IMPORTANT If the starter rope is pulled repeatedly with the choke on,
it may flood the engine and make starting difficult.
If you happen to food the engine, repeat the hot start procedure a few times to eliminate any
excess fuel.
11.3.2.2 Hot starting
To hot start the engine immediately after it has stopped, follow steps a –b –d –g of the above
procedure, making sure the primer bulb is activated 2-3 times only.
11.3.2.3 Stopping: (Fig. 28)
Stop the engine by switching off the ignition.
11.4 General working instructions
IMPORTANT! This section describes the basic safety precautions for
working with brush cutters and trimmers.
If you encounter a situation where you are uncertain how to proceed you should ask an expert.
Contact your dealer or your service workshop.
Avoid all usage which you consider to be beyond your capability.
You must understand the difference between forestry clearing, grass clearing and grass
trimming before use.
11.4.1 Basic working techniques
Always slow the engine to idle speed after each working operation. Long periods at full throttle
without any load on the engine can lead to serious engine damage.
Sometimes branches or grass get caught between the guard and cutting
attachment. Always stop the engine before cleaning.
Machines fitted with grass blades can be thrown violently to the side when
the blade comes into contact with a fixed object. This is called blade thrust.
A blade thrust can be violent enough to cause the machine and/or operator
to be propelled in any direction, and possibly lose control of the machine.
Blade thrust can occur without warning if the machine snags, stalls or
binds. Blade thrust is more likely to occur in areas where it is difficult to
see the material being cut.
Avoid cutting with the area of the blade between the 12 o'clock and 3
o'clock positions. Because of the speed of rotation of the blade, blade
thrust can occur if you attempt to cut thick stems with this area of the
blade.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 15 www.varo.com
11.4.2 Grass clearing using a grass blade
Grass blades and grass cutters must not be used on woody stems.
A grass blade is used for all types of tall or coarse grass.
The grass is cut down with a sideways, swinging movement, where the movement from right-
to-left is the clearing stroke and the movement from left-to- right is the return stroke. Let the
left-hand side of the blade (between 8 and 12 o’clock) do the cutting.
If the blade is angled to the left when clearing grass, the grass will collect in a line, which
makes it easier to collect, e.g. by raking.
Try to work rhythmically. Stand firmly with your feet apart. Move forward after the return stroke
and stand firmly again.
Let the support cup rest lightly against the ground. It is used to protect the blade from hitting
the ground.
Reduce the risk of material wrapping around the blade by following these instructions:
Always work at full throttle.
Avoid the previously cut material during the return stroke.
Stop the engine, unclip the harness and place the machine on the ground before you start to
collect the cut material.
11.4.3 Grass trimming with a trimmer head
11.4.3.1 Trimming (Fig. 29)
Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the
work. Let the cord work at its own pace. Never press the cord into the area to be cut.
The cord can easily remove grass and weeds up against walls, fences, trees and borders,
however it can also damage sensitive bark on trees and bushes, and damage fence posts.
Reduce the risk of damaging plants by shortening the cord to 10-12 cm and reducing the
engine speed.
11.4.3.2 Clearing (Fig. 30)
The clearing technique removes all unwanted vegetation. Keep the trimmer head just above
the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and
the like.
CAUTION! This technique increases the wear on the cord.
The cord wears quicker and must be fed forward more often when working against stones,
brick, concrete, metal fences, etc., than when coming into contact with trees and wooden
fences.
When trimming and clearing you should use less than full throttle so that the cord lasts longer
and to reduce the wear on the trimmer head.
11.4.3.3 Cutting (Fig. 31)
The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep
the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the
ground as this can ruin the lawn and damage the tool.
Do not allow the trimmer head to constantly come into contact with the ground during normal
cutting. Constant contact of this type can cause damage and wear to the trimmer head.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 16 www.varo.com
11.4.3.4 Sweeping (Fig. 32)
The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord
parallel to and above the area to be swept and move the tool to and fro.
When cutting and sweeping you should use full throttle to obtain the best results.
11.4.4 Trimming branch or leaves with Long-reach hedge trimmer
Work with a swinging action from the bottom upwards when trimming sides. (Fig. 33)
Always work at full throttle. (Fig. 34)
When trimming a hedge the engine should always face away from the hedge. (Fig. 34)
Hold the machine as close to your body as possible to get the best balance. (Fig. 34)
Make sure that the tip does not touch the ground. (Fig. 34)
Do not rush the work, but work steadily until all the branches have been cut back cleanly.
(Fig. 34)
11.5 Routine maintenance
11.5.1 Air filter
The air filter must be regularly cleaned to remove dust and dirt in order to avoid:
Carburetor malfunctions
Starting problems
Loss of engine power
Unnecessary wear to engine parts
Excessive fuel consumption
Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.
11.5.1.1 Cleaning the air filter (Fig. 35)
Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure
that the filter is dry before refitting it.
An air filter that has been in use for a long time cannot be cleaned completely. The filter must
therefore be replaced with a new one at regular intervals. A damaged air filter must always be
replaced.
11.5.2 Fuel filter (Fig. 36)
When the engine runs short of fuel supply, check the fuel cap and the fuel filter for blockage.
11.5.3 Spark plug
The spark plug condition is influenced by:
Incorrect carburettor adjustment.
An incorrect fuel mixture (too much or incorrect type of oil).
A dirty air filter.
These factors cause deposits on the spark plug electrodes, which may result in operating
problems and starting difficulties.
If the machine is low on power, difficult to start or runs poorly at idle speed: always check the
spark plug first before taking any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0,6-0,7 mm.
The spark plug should be replaced after about a month in operation or earlier if necessary.
Recommended Spark plug type:
Always use the recommended spark plug type! Use of the wrong spark plug can damage the
piston/ cylinder. Check that the spark plug is fitted with a suppressor.

POWXG3025 EN
Copyright © 2015 VARO P a g e | 17 www.varo.com
12 MAINTENANCE TIMESCALE
The following intervals apply to normal operating conditions only. If
your daily working time is longer or operating conditions are difficult
(very dusty work area, etc.), shorten the specified intervals
accordingly.
Before starting working
After finishing work daily
After each refueling stop
Weekly
Monthly
Every 12 months
If problem
If damaged
If required
Complete machine
Visual inspection (condition, wear,
leaks)
*
*
Clean
*
Control handle
Check operation
*
*
Air filter
Clean
*
*
*
Replace
*
*
Filter in fuel tank
Check
*
Replace filter
*
*
*
Spark plug
Readjust electrode gap
*
Replace after 100 hours of operation
Cooling inlets
Clean
*
Guide bar
Check
*
Repair or replace
*
*
Blade
Check
*
Repair or replace
*
*
All accessible screws
Check
*
Retighten
*
Anti-vibration elements
Check
*
*
*
Replace1)
*
Safety labels
Replace
*
Muffler
Clean1)
*

POWXG3025 EN
Copyright © 2015 VARO P a g e | 18 www.varo.com
13 TECHNICAL DATA
Rotation Speed (n) grass trimmer
11000min-1
Blade Size
450mm
Cylinder Capacity
33cc
Engine Power
1.0kW
Cutting width grass trimmer
430mm
Cutting width brush cutter
255mm
Cutting width hedge trimmer
390mm
Engine type
Powerplus 2-stroke engine
Oil tank capacity
0.8l
Fuel tank capacity
0.45l
Knife distance
25mm
Quick stop
Yes
Thread lengthening type
Tap&Go
Spool diameter
2.4mm
Spool length
6m
Low vibration system
Yes
Easy start
Yes
Heavy duty clutch
Yes
Fuel mixing ratio
40:1
Crank Engine
Yes
Carburetor type
Hualong
Number of teeth/ blades
12x2
soft grip
Yes
Safety guard
Yes
Handle type
Fixed
Second handle type
Adjustable auxiliary handle
Shaft type
Straight
Adjustable head
Yes
Flower protection
Yes
Laser cut blade
Yes
Two hand operation
Yes
Double action blade
Yes
E10 fuel proof
yes

POWXG3025 EN
Copyright © 2015 VARO P a g e | 19 www.varo.com
14 NOISE
Noise emission values measured according to relevant standard. (K=3)
Acoustic pressure level LpA
96 dB(A)
Acoustic power level LwA
110 dB(A)
ATTENTION! Wear hearing protection when sound pressure is over 85
dB(A).
aw (Vibration)
3.89m/s²
K = 1,5 m/s²
15 TROUBLESHOOTING
What to do when….
Source of problem
Corrective action
Source of problem
Corrective action
1. The engine will not start or will not
keep running
4. The engine runs irregularly and
lacks in power when revved
Incorrect starting
procedure
Follow the
instructions (see
chapter 3)
Dirty spark plug or
incorrect distance
between the electrodes
Check the spark
plug (see chapter
5)
Dirty spark plug or
incorrect distance
between the
electrodes
Check the spark
plug (see chapter 5)
Carburation problems
Contact your
Dealer
5. The engine makes too much
smoke
Incorrect composition
of the fuel mixture
Prepare the fuel
mixture
according to the
instructions (see
chapter 2)
Air filter clogged
Clean or replace the
filter (see chapter 5)
Carburation
problems
Contact your Dealer
2. The engine starts but is lacking in
power
Carburation problems
Contact your
Dealer
6.The machine starts to vibrate
abnormally
Air filter clogged
Clean or replace the
filter (see chapter 5)
Damaged or loose
parts
Stop the
machine and
disconnect the
spark plug cable.
Inspect for
damage. Check
for and tighten
any loose parts.
Have all checks,
repair work and
replacements
carried out by a
specialized
Centre only.
Carburation problem
Contact your Dealer

POWXG3025 EN
Copyright © 2015 VARO P a g e | 20 www.varo.com
16 WARRANTY
This product is warranted for a 36-month period effective from the date of purchase by the
first user.
This warranty covers all material or production flaws excluding : batteries, chargers,
defective parts subject to normal wear & tear such as bearings, brushes, cables, and
plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects
resulting from maltreatment, accidents or alterations; nor the cost of transportation.
Damage and/or defects resulting from inappropriate use also do not fall under the
warranty provisions.
We also disclaim all liability for any bodily injury resulting from inappropriate use of the
tool.
Repairs may only be carried out by an authorised customer service centre for Powerplus
tools.
You can always obtain more information at the number 00 32 3 292 92 90.
Any transportation costs shall always be borne by the customer, unless agreed otherwise
in writing.
At the same time, no claim can be made on the warranty if the damage of the device is the
result of negligent maintenance or overload.
Definitely excluded from the warranty is damage resulting from fluid permeation, excessive
dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate
usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not
following the instructions given in the manual), inexpert assembly, lightning strike,
erroneus net voltage. This list is not exhaustive.
Acceptance of claims under warranty can never lead to the prolongation of the warranty
period nor commencement of a new warranty period in case of a device replacement.
Devices or parts which are replaced under the warranty therefore remain the property of
Varo NV.
We reserve the right to reject a claim whenever the purchase cannot be verified or when it
is clear that the product has not been properly maintained. (Clean ventilation slots, carbon
brushes serviced regularly, etc.).
Your purchase receipt must be kept as proof of date of purchase.
Your appliance must be returned undismantled to your dealer in an acceptably clean state,
(in its original blow-moulded case if applicable to the unit), accompanied by proof of
purchase.
17 ENVIRONMENT
Should your appliance need replacement after extended use, do not dispose of it with the
household refuse, but in an environmentally safe way.
Please dispose of used motor oil in a manner that protects the environment. We suggest you
take it in a sealed container to your local service station for recycling. Do not throw it into the
refuse or pour it on the ground.