VATOO VDP-100 User manual

VDP-100 USER MANUAL
VATOO INC

VATOO INC
Title
VDP-300 Intercom User Manual
Version
V1.0
Release
2014.01.20.
CONTENTS
1. VDP-100 INTERCOM FEATURES .................................................................................3
2. VDP-100 INTERCOM FUNCTIONS................................................................................4
2.1. BUTTONS.................................................................................................................................4
2.2. VOLUME CONTROL..................................................................................................................4
2.3. GROUP SETTING ......................................................................................................................4
2.4. ID SETTING .............................................................................................................................5
2.5. CHARGING BATTERY ................................................................................................................5
2.6. SPECIFICATIONS..................................................................................................................7

VATOO INC
Title
VDP-300 Intercom user Manual
Version
V1.0
Release
2014.01.20.
1. VDP-300 intercom Features
Power Switch
USB Charger Port
LCD
UP Button
Function Button
DOWN Button
Mode Button
AUX IN/OUT
Headset IN

VATOO INC
Title
VDP-300 Intercom User Manual
Version
V1.0
Release
2014.01.20.
VDP-300 intercom Functions
1.1. Buttons
Button
Function Description
Power Switch
Upward : Power ON
Downward : Power OFF
Mode
Talk channel On/Off
Function
To set group mode or ID mode
Up
VOL : To set volume level higher
Down
VOL: To set volume level lower
1.2. Volume Control
VDP-300 intercom has volume control function that serves user to change volume level wanted.
How to set
VOL is displayed right after power is turned on. The default mode is volume control
mode
In Volume mode, volume can be set with UP/DOWN button in the range of 0 ~ 8.
1.3. Group setting
VDP-300 intercom has group setting function that serves user to change group to communicate.

VATOO INC
Title
VDP-300 Intercom user Manual
Version
V1.0
Release
2014.01.20.
How to set
After turned on, phone is in volume control mode.
To change volume mode into group mode, press Up + Down buttons at the same
time.
In Group mode, group can be set with UP/DOWN button in the range of 0 ~ 39.
1.4. ID Setting
VDP-300 intercom has ID setting function to communicate with each other. Each intercom has to
have an unique Identification number in the same group and Master’s ID must be set “00”.
How to set
After turned on, phone is in volume control mode.
To change volume mode into group mode, press Up + Down buttons at the same
time
Press Function button to move ID change mode as below.
In ID change mode, ID can be set with UP/DOWN button in the range of 0 ~ 99.
1.5. TALK Function
VDP-300 intercom serves TALK function to let users start to talk with others. In case of Master, the
default talk mode in ON, and in case of Slaves the default talk mode is in inactive state. Therefore

VATOO INC
Title
VDP-300 Intercom User Manual
Version
V1.0
Release
2014.01.20.
Master can start to talk after power is turned on, Slaves are required to press Mode button then
Talk function is activated. Talk function is available in 6 phones including Master at the same time.
While 5 slaves are using Talk, if another slave tries to talk by pressing mode button, Master
release one of 5 slaves that accessed first and allows the latest one to use Talk. In this way 6
persons can keep talking.
1.6. Charging battery
VDP-300 intercom is put in lithium-ion battery.
User can charge battery with charger supplied through Micro USB port.
During charging battery, the red LED at the right top of front face is turned on.

VATOO INC
Title
VDP-300 Intercom user Manual
Version
V1.0
Release
2014.01.20.
1.7. SPECIFICATIONS
ITEM
SPECIFICATION
Radio Frequency Type
ISM 2403MHz ~ 2479MHz
Type
Wireless Microphone/Receiver Unit
Radio Interface
ISM 2.4GHz: GFSK Modulation with Frequency Hopping
Output Power: Class 1(100mW)
Voice Codec
16bit/16KHz
Tx Max Output Power
100mW
Rx Sensitivity
-95dBm
Voice Latency
< 30ms
Channel Spacing
2MHz
Data Rate
2Mbps
Freq. Bandwidth
2MHz
Battery
Li-ion Battery @3.7V/ TBD 1100mA
Antenna
Internal Chip Antenna
Talk Time for Microphone
15hr Typ.
Power Consumption(Microphone)
Avg. 100mA at Class 1(100mW)
Distance Range(LOS)
100M @ Class 1
Frequency response
50 Hz ~ 4 kHz
FCC NOTICE TO USERS AND PROCUCT
STATEMENTS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
The antennas used for this transmitter must be installed to provide a separation distance of at
least 25 mm from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this equipment near water.
6) Do not using near any heat sources such as radiators, heat resisters, stove, or other
equipment that produce heat.
European CE notice to users and product statements
This product is CE marked according to the provisions of the R&TTE
Directive(99/5/EC). Hereby, VATOO INC declares that this product is in
compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
For further information, please contact www.vatooinc.com
VATOO INC.
320rm, H, 270, Gyeonggigwagi-dearo 270 Siheung City Gyeonggi-do 429-792,
korea
Tel: [phone] / Fax: [phone]
URL: www.vatooinc.com

CONTACT INFORMATION
Manufacturer Address : 320rm, H, 270, Gyeonggigwagi-dearo 270 Siheung City Gyeonggi-do 429-792, korea
To locate in-country VATOO INC distributors of the Wireless Intercom
please refer to the VATOO INC, Website http:// www.vatooinc.com
These distributor(s) represent local contacts for this product.
CORPORATE HEADQUARTERS:
VATOO INC
320rm, H, 270, Gyeonggigwagi-dearo 270 Siheung City Gyeonggi-do 429-792, korea
Tel: [phone]
Fax: [phone]
Web: http:// www.vatooinc.com
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is Subject to the following two condition: (1) this device may not cause interference
,and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.

EUROPEAN UNION “DECLARATION OF CONFORMITY”
DECLARATION OF CONFORMITY
VATOO INC
320rm, H, 270, Gyeonggigwagi-dearo 270 Siheung City Gyeonggi-do 429-792, korea
declare under our sole responsibility that the product(s)
Wireless Intercom – VDP-300
to which this declaration relate(s) is in conformance with the following standards:
EN 301 489-1 V1.9.2:2011
EN 301 489-17 V2.2.1 :2012
EN60950-1:2006
EN 300 328 V1.7.1:2006
following the provisions of the 1999/5/EC Directives.