Vcomm resi-link RL-BV140A User manual

®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
ABN: 99 091 281 524
Vcomm Pty Ltd
RL-BV140A / RL-BV150B
AV Distribution Range
‘linx-AV’ Quad IR Composite AV Balun Transmitter (1:4)
Composite IR AV Balun Receiver
A RCA Video and Audio input
B Loop Through RCA
Video and Audio output
C IR Emitter output
D IR / Power LED’s
E 12V DC Power input
F RCA Video output
G RCA Audio output
H IR Target input
A
B
CD E FG
H
Cable Requirements
4 pair twisted cable
Hardware Connection
1. Ensure all power to equipment is switched off prior to
installation.
RL-BV140A
2. Connect RCA cable from terminals A of Transmitter to
the AV source.
3. Connect a second RCA cable from loop through
terminals B of Transmitter to the AV input of the local
device if required.
4. Connect RL-IR700/800* IR emitter to the output C of
Transmitter. Place the other end within 25cm of the IR
receiver on the AV source (depending on environmental
conditions).
5. Connect RJ45 socket (Output A) of Transmitter to RJ45
input of Receiver in zone A.
RL-BV150B
6. Connect Video lead (yellow to yellow) from RCA Video
Output F of Receiver to the yellow RCA Video input on
AV device (TV, etc).
7. Connect Audio lead L & R RCA connectors (R&W) from
output G on Receiver, to the corresponding RCA
inputs on the AV device (TV, etc).
8. Connect RL-BV500* IR target to input H on Receiver.
Flat target can be easily mounted (either directly using
adhesive backing, or by using RL-ACC150* Target
Mount) to the desired location, anywhere within the line
of sight of remote controls.
9. Repeat steps 5 - 8 for connection of zones B, C and D.
10. Connect supplied 12V DC switch mode power pack to
power input E on Transmitter.
11. Once installation is complete, switch on power to
all equipment. Check green PWR LED D on
Transmitter is illuminated.
RL-BV140A
IR
RL-BV150B
* Sold separately
www.resi-linx.com
INSTALLATION MANUAL
Transmitter Receiver
RJ45 Output RJ45 Input

®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV140A / RL-BV150B
AV Distribution Range
‘linx-AV’ Quad IR Composite AV Balun Transmitter (1:4)
Composite IR AV Balun Receiver
www.resi-linx.com
ABN: 99 091 281 524
Vcomm Pty Ltd
INSTALLATION MANUAL
Troubleshooting
IR LED indicator on RL-BV140A Transmitter illuminates
briefly upon receipt of IR commands.
NOTE: Some brands of TV/Monitors can reduce the
range of the IR Receiver head, which is outside the
scope of the warranty.
RL-BV140A/150B
Power - BV140A 12V DC 500mA Switch Mode
Maximum video input - BV140A 1.2V P-P
Return loss >15dB to 1,000 MHz
Common mode rejection >40dB @ 1,000 MHz
Maximum distance cable Up to 100m
Video Signal Composite
Audio Signal Analogue
Conguration 1:4
IR capability Yes
Loop Through capability Yes
Connections In/Out - BV140A
- BV150B
2 sets - 3 x RCA
4 x RJ45
1 x IR Emitter
3 x RCA
1 x RJ45
1 x IR Target
Zone A
RL-BV140A
RL-BV150B
Connection to zones B, C and D
as above
Loop Through terminals
to be connected to local
AV device if required
Remote
Control
RL-BV500
Output A