Vega D4-F User manual

Vega Light Control Systems ●Holland, Michigan 49424
D4 Post Top Retrofit Kit
INSTALLATION GUIDE
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
WARNING
!
•RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OF THIS RETROFIT ASSEMBLY REQUIRES A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTRICAL SYSTEM. IF NOT
QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.
•RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN THE LUMINAIRES THAT HAS THE
CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND
WHERE THE INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING OF THE
LUMINAIRE.
•RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRE WIRING AND ELECTRICAL PARTS MAY BE DAMAGED
WHEN DRILLING FOR INSTALLATION OF LED RETROFIT KIT. CHAECK FOR ENCLOSED WIRING AND PARTS.
•ONLY THOSE OPEN HOLES INDICATED IN THE PHOTOGRAPS AND/OR DRAWINGS MAY BE MADE OR
ALTERED AS A RESULT OF KIT INSTALLATION. DO NOT LEAVE ANY OTHER OPEN HOLES IN AN
ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS.
•DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL
COMPONENTS DURING KIT INSTALLATION.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR
OTHER SHARP OBJECTS.
•THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE
COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
•
•RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE. L’INSTALLATION DE CE NÉCESSAIRE DE MODERNISATION
EXIGE UNE PERSONNE FAMILIÈRE AVEC LA CONSTRUCTION ET LE FONCTIONNEMENT DU SYSTÈME
ÉLECTRIQUE DU LUMINAIRE ET DES RISQUES ASSOCIÉS. TOUTE PERSONNE QUI N’EST PAS QUALIFIÉE
NE DOIT FAIRE AUCUNE TENTATIVE D’INSTALLATION ET DOIT CONTACTER UNE PERSONNE QUALIFIÉE.
•RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE. N’INSTALLER CE NÉCESSAIRE QUE DANS LES
LUMINAIRES DONT LES CARACTÉRISTIQUES DE CONSTRUCTION ET LES DIMENSIONS SONT CONFORME
À CELLES ILLUSTRÉES DANS LES PHOTOS ET/OU LES DESSINS ET DONT LA PUISSANCE D’ENTRÉE
NOMINALE DU NÉCESSAIRE DE MODERNISATION NE DÉPASSE PAS CELLE DU LUMINAIRE.
•IL EST INTERDIT DE FAIRE OU DE MODIFIER UNE OUVERTURE DANS UN BOÎTIER DE CÂBLAGE OU DE
COMPOSANTS ÉLECTRIQUES AU COURS DE L’INSTALLATION DU NÉCESSAIRE.
•AFIN DE PRÉVENIR L’ENDOMMAGEMENT OU L’ABRASION DES CÂBLES, ÉVITER TOUT CONTACT ENTRE
CES DERNIERS ET LE BORD D’UN OBJET TRANCHANT TEL QU’UNE TÔLE.
•LE NÉCESSAIRE DE MODERNISATION EST ACCEPTÉ À TITRE DE COMPOSANT D’UN LUMINAIRE LORSQUE
LA PERTINENCE DE LA COMBINAISON DOIT ËTRE DÉTERMINÉE PAR PAR LES AUTORITÉS COMPÉTENTES
The D4 Post Top Retrofit Kits from Vega Light Control Systems
•Designed as an easy and reliable way to convert existing fixtures
•Alternative to HID lamps, up to 300W MH and 200W HPS
•Use for pole heights up to 30 feet
•Eliminates mercury & lead
•Reduce carbon footprint & light pollution.
•Tested to the most demanding industry standards:
oLM-79, LM-80, In-Situ, TM-21, and DLC
osurge testing to UL 1449 3rd edition
oUL 1598C 1st Ed. and CSA TIL B-79A
INS-00690-01 20181028
AVERTISSEMENT

Vega Light Control Systems ●Holland, Michigan 49424
NOTICE
•TO AVOID ELECTRIC SHOCK, DISCONNECT POWER BEFORE ATTEMPTING INSTALLATION OR SERVICING.
•TO PREVENT ELECTRIC SHOCK THIS PRODUCT MUST BE PROPERLY GROUNDED.
•INSTALLATION MUST BE STRUCTURALLY SOUND TO PREVENT PERSONAL INJURY DUE TO FIXTURE COLLAPSE.
•USE CAUTION WHEN HANDLING DURING OR AFTER OPERATION AS IT MAY BECOME HOT AND CAUSE BURNS.
•FAILURE TO INSTALL THIS PRODUCT IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC), OR THE CANADIAN
ELECTRICAL CODE (CSA 22.1), ALL APPLICABLE FEDERAL, STATE AND LOCAL ELECTRIC CODES AS WELL AS THE
SPECIFIC UNDERWRITERS LABORATORIES (UL) SAFETY STANDARDS FOR THE INSTALLATION, LOCATION AND
APPLICATION MAY CAUSE UNSAFE SITUATIONS LEADING TO SERIOUS PERSONAL INJURY, DEATH, PROPERTY
DAMAGE AND/OR PRODUCT MALFUNCTION.
•THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
•FAILURE OF FIXTURE TO PROVIDE SUFFICIENT WEATHER PROTECTION VOIDS WARRANTY.
•TO PREVENT EARLY PRODUCT FAILURE, THIS PRODUCT SHOULD BE INSTALLED IN OPERATING ENVIRONMENTS WITH
MAXIMUM MEAN FIXTURE AMBIENT OPERATING TEMPERATURE FOR LED RETROFIT MODULE: 104°F (40C); MAXIMUM
AMBIENT OPERATING TEMPERATURE CANNOT EXCEED 140°F (60°C).
•INSTALLATION REQUIREMENTS MAY VARY DEPENDING ON THE LUMINAIRE RETROFITTED.
•IF UNCERTAIN, CONTACT VEGA LIGHT CONTROL SYSTEMS CUSTOMER SERVICE TO EVALUATE APPLICABILITY TO
FIXTURE. [email protected], PHONE: [phone]
1. PRODUCT OVERVIEW
1.1. D4 Post Top Retrofit Specifications
LED Light Engine
•30W, 40W, 60W, and 80W Versions
•2200K, 3000K, 4000K and 5000K CCT Available
•Type 3 and Type 5 Available
•True photometric performance through silicone optics
•Dimming Options:
•0-10vdc dimming available
•Timer based overnight schedules
Mechanical Details
•4.73” & 5.91” Diameter Light Engines fit ALL globes
•Telescoping center post for height adjustment, field settable
•Universal Mounting plates available in 4 sizes; 6.25”, 6.5”, 7” or 8” diameter
•Brand specific quick change mounting plates also available
•Power supply housing and bracket designs to mount above, midway, or below globe/fixture base
•Downlight light option for suspended LED engine in shoeboxes, pendants, and colonials.
Performance Details
•5 Year replacement warranty, extended warranties available
•18kA series surge suppression designed to UL1449 3rd edition
•Drivers qualified to:
•Life > 50,000 hours
•power factor of ≥0.9
•THD of ≤20%
•LEDs qualified to:
•DLC Premium models –L70 of 100,000 hours minimum, L90 of 36,000 hours min.
•DLC Standard models –L70 better than 50,000 hours

Vega Light Control Systems ●Holland, Michigan 49424
1.2. Products Covered
P/N Format: D4 - (style)(watts) - (cct)K - T(type)M - (mounting) - (dimming)
Full Enclosure Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-F 30 -22K - T5M - 625 - STD Universal 6.25" plate
D4-F 40 -30K - T3M - 6S - DIM Universal 6.5" plate
D4-F 60 -40K -7S - PXYZ# Universal 7" plate
(80 NA) -50K -8N Universal 8" plate
-C### Other custom configurations
-H### "H" prefix is high output version
Typical Application: Generic shallowfitter where ballast was mounted under cover above fitter
Mid Mount Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-M 30 -22K - T5M - CHBTL - STD Hadco B Twistlock
D4-M 40 -30K - T3M - CHBSP - DIM Hadco B Pin & Screw
D4-M 60 -40K - CSBSC - PXYZ# Sternburg Spring Clips
D4-M 80 -50K - CSBTL Sternburg Twistlock
-H### "H" prefix is high output version
- #XX Universal Plates above also applicable
Typical Application: Deeper fitters such as petal style where ballast was mounted into fitter by top plate/cover.
Granville Classic Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-H 30 -22K - T5M - CGVC7 - STD Granville Classic 7" Fitter or 4" Fitter
D4-H 40 -30K (T3M- NA) - HGVC7 - DIM "H" prefix is high output version
D4-H 60 -40K - PXYZ#
(80 NA) -50K
Typical Application: Specific configuration for mounting in Granville Classic 7" and 4" fitters with 19" glass globes.
One piece assembly
Granville Premier Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-H 30 -22K - T5M - CGPCS - STD Granville Premier w/Photo Control Socket
D4-H 40 -30K (T3M- NA) - CGPNS - DIM Granville Premier w/o Photo Control Socket
D4-H 60 -40K -H### - PXYZ# "H" prefix is high output version
(80 NA) -50K
Typical Application: Specific configuration for mounting in Granville Premier fitters with 19" glass globes.
Two piece assembly.
Downlight Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-S 30 -22K - T5M - DNLT - STD 120mm Light Engine flexible Downlight Kit
D4-S 40 -30K - T3M - DNLT2 - DIM 150mm Light Engine flexible Downlight Kit
D4-S 60 -40K - CADJ1 - PXYZ# 14" to 23" span, Larger fixture Downlight Kit
D4-S 80 -50K -C### Other custom configurations
-H### "H" prefix is high output version
Typical Application: Shoebox, Pendant, and Colonial fixtures. Light Engine mounts separately on adjustable arms.
OEM Components Kit Style Watts - CCT - Type - Mounting - Dimming Mounting Code Details
D4-C 30 -22K - T5M - COEM1 - STD OEMCustomer, configuration 1
D4-C 40 -30K - T3M - CCC01 - DIM OEMCustomer CC, configuration 1
D4-C 60 -40K -CCC02 - PXYZ# OEMCustomer CC, configuration 2
D4-C 80 -50K -C### Other custom configurations
-H### "H" prefix is high output version
Typical Application: LED Light Engine and Power supply only. OEMprovides light engine mount.

Vega Light Control Systems ●Holland, Michigan 49424
1.3. D6 LED Retrofit Kit Product Description
Notes:
•Product has been properly packed to the protect during transit. Inspect and notify the distributor or shipping agent of any damage found.
•For additional information visit www.vegalightcontrolsystems.com, email [e-mail] or call 616-259-0700
* Side Brackets may be used to the span the width of a fixture or used to screw mount LED light engine to the hood of a light.
Part included in kit as needed:
Surge
Protector
Power Supply
Assembly
4.73”
[120 mm]
2.75”
[70 mm]
LED Light
Engine
Height
Adjustable
From 15”
Down
To 9.75”
D4-F Model
Fully Enclosed, 60W Max
Adapter Plate
D4-S Down Light Model
with Side Brackets*
D4-M Model
Mid-Mount Enclosed, 80W Max
4.73”or 5.91”
[120 or 150 mm]
Height
Adjustable
From 11”
Down
To 9.75”
Connected by 24”Cable w Connectors
6.6”[167 mm]
4.5”
[115 mm]
D4-C Model
Socket Replacement
4.73”or 5.91”
[120 or 150 mm]
6.6”
[167 mm]
4.5”
[115 mm]
Extrusion
(optional)
Tubing
Made to
order
D4-H CGVC Model
Granville Classic, 60W Max
4.73”or 5.91”
[120 or 150 mm]
7.9”
[201 mm]
D4-H CGVP Model
Granville Premier, 60W Max
7.2”
[183 mm]
Photo Control
Socket
(optional)
4.73”or 5.91”
[120 or 150 mm]
Required Tools and Hardware (Not provided)
•Flat and Phillips Head Screwdriver, Pliers,
Wire strippers, Screws retained from fixture
Hex Key 3/32”
Wire Nuts

Vega Light Control Systems ●Holland, Michigan 49424
1.4. Fixture Considerations
1. Do not use a Type 3 LED Light Engine in a Refracted Globe. Type 3 Refracted globes will effectively convert
the T5M retrofit kit into a Type 3 distribution in globes such as the Lindy Type 3 and the Granville Type 3.
2. Do not mount LED Light Engine too high in the globe. The LED Light Engine needs adequate air space
above it to dissipate heat. Additional air space may be needed for Tc limits as shown below.
3. The arc tube height of the previous HID system is typically the proper height for the LED mounting. This is
especially true for refracted globes to maintain the proper pattern of light to the ground and avoid excessive up
light.
4. Example Globes vs LED height settings:
✓LexaLite Lindy 424 globe arc tube height is designed at 11.3” from the base of the globe.
✓LexaLite Lindy 408 globe performs best at LED height set 8” from the base of the globe.
✓Crown 88266-CL has an optimum output when set 13” from the base of the globe.
5. Measure the maximum temperature achieved at the locations shown below after at least 2 hours under power
inside fixture. Take that temperature and add the difference between room temperature and 40C to calculate
the maximum Tc.
✓For example: Room is 22C, Tc measured is 62C, the compensated maximum Tc is 80C
6. When using Type 3 LED Retrofit Kits orient the LED Light Engine as shown below
LED Light Engine
Tc Point < 90C
Osram Power Supply
Measured at marked Tc Point < 85C
Remove power supply cover as needed to reach Tc point on power supply
Meanwell Power Supply
Tc Point < 85C
Measured at center of label
When the arc tube
height is unknown,
place the LED height at
the center of the globe.
This LED surface is
should be installed at the
previous arc tube height.
150mm 80W LED Light Engine
120mm 30-60W LED Light Engine
Street Side
Arrow
House
Side
House
Side
Street
Side
Street
Side

Vega Light Control Systems ●Holland, Michigan 49424
2. INSTALLATION INSTRUCTIONS
•Refer to fixture installation manual for fixture mounting procedures
•Please refer to www.vegalightcontrolsystems.com for additional install instructions
2.1. STEP 1: Prepare fixture for installation
•Turn power off before attempting installation
•Remove lamp, original optical components, socket, and ballast
•Remove internal reflectors or Lite Lid
•If photocell-controlled, connect unit after external control
WARNING
!Risk of electric shock
Disconnect power before servicing
WARNING
!Risk of burn
Allow unit to cool fully before servicing
POST-TOP
Note: Failure to remove original components
including ballast will void product warranty.
Original optical
components
(reflectors)
Fixture Dome Top
Ballast
Socket
Lamp
Fixture Base
Fixture Globe
Note: Kits are available for specific
targeted luminaries
Holophane:
Granville Premier cat. No. GVP
Granville Classic cat. No. GV
SHOEBOX
Fixture Cover
Remove:
•Fixture cover
•Original ballast
•Reflector housing
•Ballast bracket
Save all mounting screws
Note: Minimum Total
Fixture Dimensions
✓Width –12”
✓Depth –17”
✓Height –6”
Reflector
Housing
Original Ballast
Note: Kits are available for specific
targeted luminaries
RUUD model PR series
Granville Classic cat. No. GV

Vega Light Control Systems ●Holland, Michigan 49424
SIDE BRACKET MOUNTING
Recommended Fixtures:
•Shoebox
•Pendant
•Colonial
Standard Side Brackets shown.
Other configurations available.
2.2. STEP 2: Fitting of LED Retrofit Kit into Fixture
•Review the various mounting configurations on the following pages and select the most applicable model
•Select and install appropriate mounting accessories if needed
•Based on the fixture type, configure power supply assembly, brackets, and height (see 1.4.2-5)
Notes:
•Center Pole Mounting height can be adjusted using the included hex key to loosen set screw and slide LED to
needed position. Be sure to also pull or push LED cable into position while adjusting height. After adjusting height,
tighten set screw enough to hold tube, then tighten another ½ turn with hex key. (see 1.4.2-4)
•Side brackets can be adjusted, bent, trimmed, or special ordered to span or offset LED mounting height.
•Allow adequate space around all sides of LED Light Engine from fixture or globe. (see 1.4.5)
•Order a lower wattage of kit if install is still exceeding Tc limits with LED kit properly positioned.
•Assembled Retrofit Kit may be special ordered configured ready to drop into light fixture. These options include:
oSize and position of mounting plate and or custom mounting plates
oHeight of Light Engine set to specified height
oAccessory Brackets attached
•Contact Matech with any mounting questions or concerns.
Height
Adjustable
From 15”
Down
To 9.75”
CENTER POLE MOUNTING
Recommended Fixtures:
•Post Top
Height
Adjustable
From 11”
Down
To 9.75”
Socket Replacement
Height Made to Order
Mounting Plates
available for most fitters

Vega Light Control Systems ●Holland, Michigan 49424
2.3. STEP 3: Install retrofit kit in fixture
Power Supply Above or Mid Mount
Power Supply Down below Mounting Plate
Notes:
•For Type 3, ensure LED head is rotated with “Street Side” of light engine facing the street (see 1.4.6)
•Re-use screws previously holding HID ballast to fixture to attach Retrofit Kit when possible. Additional hardware
maybe required.
•For Post Top fixtures, LED Light should be installed to maintain cooling clearance above heatsink and at arc
tube height of replaced HID. (see 1.4.5)
•Restore the original light fixture sealing for water and insect control. Rain water must not enter the wiring
compartment.
CENTER POLE MOUNTING

Vega Light Control Systems ●Holland, Michigan 49424
2.4. STEP 4: Make electrical connections
•Connect line voltage wires using wire nuts as shown in the wiring diagram in Section 3
➢Strip wires appropriately for the wire nuts utilized, 3/8” for those included in the kit.
➢The surge protector and power supply are universal voltage.
➢The white wire may be either Neutral or Line.
➢Green/Yellow wire is tied to grounding conductor.
•Connect low voltage wires if they are separated during install.
➢Plug connectors together when supplied with 2 pin Molex connectors between LED and driver.
➢If loose wires connect White LED wire to positive driver lead (Red) and Gray LED wire to negative driver
lead (Black or Blue) using pre-installed Lever Nuts.
•If photocell-controlled or remote controlled, connect Retrofit Kit to output of the control
2.5. STEP 5: Secure fixture components
•Secure fixture components and restore original light fixture sealing for water and insect control.
Notes:
•Additional hardware maybe required to mount LED Retrofit Kit in fixture
•Re-use screws previously holding HID ballast to fixture to attach Retrofit Kit when possible.
•LED Light should be installed to maintain cooling clearance above heatsink (see 1.4.5)
•For Type 3, ensure “Street Side” of light engine faces the street
Note: Screws used to mount LED module and power supply
in fixture are existing screws from previous HID system.
For a Post Top Fixture
SIDE BRACKET MOUNTING
Note: Screws used to mount LED module and power supply
in fixture are existing screws from previous HID system.
For a Shoe Box fixture

Vega Light Control Systems ●Holland, Michigan 49424
3. ELECTRICAL INSTRUCTIONS
3.1. Wiring diagram after installation
4. RELATED INFORMATION
4.1. Maintenance and Cleaning
•Periodic cleaning of fixture will ensure operation at maximum optical efficiency
•Refer to fixture installation instructions for maintenance and cleaning guidelines
•Even though LED Retrofit Kit may continue to light after the specified lifetime has passed, it must be replaced in
order to maintain appropriate light levels
4.2. List of applicable and related Documents
•D4 LED Retrofit Kit Product Information Brochure
5. Troubleshooting
Condition
Possible Reason(s)
Recommended Action
AC surge protector
damaged
Surge protector unable to protect
unit
1. Verify AC voltage at both input and output of surge protector.
2. If within warranty period, contact VEGA sales representative for RMA.
3. If out of warranty period, contact VEGA sales representative for
information to replace surge protector.
LEDs are dim or not lit
1. DC Cable is unplugged.
2. Power supply has failed
3. LED board is damaged
1. Connect the DC Cable by plugging together the two Molex connectors
2. To identify failed power supply, use clamp meter (tongs) to measure
output current. Replace if below rated current. Before replacing power
supply, verify AC voltage through surge protector.
3. If within warranty period, contact VEGA sales representative for RMA.
If not within warranty period, LED Light Engine should be replaced as it
is not user serviceable.
Difficulty experienced
during mounting
---
Contact VEGA representative for recommended action
[e-mail]
616-259-0700
OR visit www.vegalightcontrolsystems.com for additional reference designs.
AC POWER SIDE
120-277 VAC
LED SIDE 36 VDC.
18AWG Wires
Note: AC surge protector to power supply is prewired