Vello BG-C9 User manual

BG-C9
BATTERY GRIP
Designed For The Canon 5D
Mark III SLR Camera
USER’S MANUAL

Introduction
Thank you for choosing Vello and congratulations
on your new BG-C9 battery grip purchase. Enjoy
the many benefits that a battery grip offers, such as
extended shooting time and more control and comfort
when shooting in a vertical (portrait) orientation.
The Vello BG-C9 is compatible with the Canon 5D
Mark III SLR camera. The BG-C9 accepts two Canon
LP-E6 rechargeable batteries, or six AA batteries
(alkaline, Ni-MH, lithium, or nickel-manganese) can
be used instead for added convenience. The BG-C9
is equipped with an alternate shutter-release button,
AF start button, AF point selection, AE lock/FE lock
button, multi-controller button, multi function button,
and main dial for shooting in a vertical position.
Please read through this entire manual before using
the BG-C9 battery grip.
2

Precautions
1. The BG-C9 should only be used with compatible
devices specified in this manual.
2. Only use with batteries and battery holders
recommended in this manual.
3. Cover the power terminals with the contact cap
when the BG-C9 is not in use. This prevents
electrical shorts caused by metal objects touching
the power terminals.
4. When the battery holder is removed from the
grip, remove the batteries or place the holder in
a container to prevent electrical shorts caused by
contact with other metal objects.
5. If you notice smoke, an unusual smell or noise from
the battery pack, discontinue use immediately.
Remove the batteries and take the device to a
Vello authorized reseller.
6. Turn the grip power off when not shooting
vertically.
7. The battery level may not display properly if
batteries are inserted before mounting the grip.
8. Remove batteries from the grip when not in use.
9. Do not attempt to disassemble.
10. Avoid water or extreme humidity and keep in a
dry and cool place.
11. Keep out of reach of children.
3
OVERVIEW INTRODUCTION
ASSEMBLY

Overview
4
67
11 12 13
114
18
19
9
2
5
8
20 21
3
17
1516
10
4

1
Contact Cap
Protects grip contacts. Keep covered
when the grip is not in use.
2Electrical Contacts
Communicates with the camera
electronics.
3
Mounting Screw
Aligns with the camera’s tripod
socket.
4Guide Pin
Helps align the camera to the grip.
5Battery Tray Lever
Locks and unlocks the battery
compartment door.
6Battery Tray Compartment
Houses the battery tray.
7DC Coupler Cord Mount
Groove for use with the Canon AC
Power Adapter (ACK-E6).
8Attachment Wheel
Secures the grip to the camera.
9Grip Power ON/OFF
10 Multi-Controller Button*
11 AF Point Selection/Magnify Button*
12
AE Lock/FE Lock/Index/Reduce
Button*
13
AF Start Button
14 Shutter-Release Button*
15 Multi Function Button*
16
Main Dial*
17 Camera Battery Chamber Cover
Holder
Stores the cover when the grip is
mounted.
18 Hand Strap Mount
19 Tripod Socket
20 Battery Tray
Holds up to two Canon LP-E6
batteries.
21 AA Battery Tray
Holds up to six AA batteries.
* Performs the same function as on the
camera.
OVERVIEW INTRODUCTION
ASSEMBLY
5

Attaching The Grip
1. Ensure that the power is
turned off on the camera
and that the power switch
is set to OFF on the
battery grip.
2. Remove the battery
from the camera battery
compartment.
3. Open the camera
battery chamber cover
and remove as indicated
above.
6

4. To prevent loss, place the
camera battery chamber
cover into the BG-C9
battery chamber holder.
as indicated above. Swing
the battery chamber cover
shut so that it locks into
place
5. Remove the protective
cap and connect the BG-
C9 grip to the camera,
while aligning the grip’s
mounting screw with the
camera’s tripod socket.
6. Rotate the attachment
wheel in the direction
shown by the arrow until
it is firmly tightened.
1
2
3
When removing the grip,
turn the camera power off,
remove batteries, and replace
protective contact cap.
7
OVERVIEW INTRODUCTION
ASSEMBLY

Inserting Batteries
1. Ensure that the power is
turned off on the camera
and the grip. Use your
fingernail to protrude the
battery tray lever so you
can rotate and pull as
indicated above, and slide
the battery tray out of the
grip.
2. Canon LP-E6 Batteries:
Insert up to two batteries
by placing them into either
slot in the battery tray,
while ensuring the correct
orientation as shown on
the tray.
3. AA Batteries: Place six
new AA batteries of the
same type into the AA
battery holder as shown,
while ensuring that they are
in the correct orientation.
8

4. Rotate the battery tray
lever counterclockwise
and slide the battery
tray all the way into the
grip. Rotate the lever as
indicated above and push
the it back into place to
lock the tray.
5. Switch the grip power
to ON and then turn
on the camera’s power.
Check the battery level
in the control panel or
viewfinder.
6. Household Power Outlet:
The Canon ACK-E6
AC Power Adapter Kit
(sold separately) can be
connected to the grip.
Place the DC coupler
through the small groove
on the back of the grip.
Ensure that the cord
doesn’t get pinched by the
battery holder.
9
OVERVIEW INTRODUCTION
ASSEMBLY

Specifications
Power Source 1. One or two Canon LP-E6 rechargeable batteries
2. Six AA/LR6 Alkaline batteries
3. Works with the Canon AC Adapter Kit ACK-E6 (sold separately)
Operating Temperature 32 – 104 °F (0 – 40 °C)
Dimensions Approximately 6.0 × 4.5 × 3.4 in. (153.1 × 113.3 × 85.7 mm)
Weight Approximately 10.4 oz. (294.8 g) (excluding battery tray and batteries)
* Approximate measurements.
Specifications and design are subject to change without notice.
AA batteries do not provide as much shooting time as LP-E6 rechargeable batteries. Performance of AA batteries may also be dependent
on brand and storage conditions. AA batteries may not function under 68º F (20º C).
Please note: When using the AA battery tray, the battery indicator will only work with Ni-MH batteries.
This product is not compatible with Duracell®brand alkaline batteries.
10