Veloteq CF-2104 User manual

1
User Manual

2
一、
1. This product is a Home Use Treadmill. Heart rate sensor does not belong to the
medical equipment, just for your reference.
2. When using this Treadmill, in its rear should be vacated 2m*1m as security zone, and
should not place any stuff within security zone.
3. The Treadmill is suitable to place indoor of avoiding damp, does not allow to splash
water or place any stuff on it.
4. When running the Treadmill, DC Motor may bring spark, should be kept away from
Inflammable and explosive materials.
5. In use, should ensure the Treadmill to put on plat ground, if not, to adjust the mat below
or using carpet、rubber sheet to make it smooth.
6. The voltage is 220V-240V, exceed the range of voltage, may it doesn’t’t work properly.
The power has to match the power line and single-phase, three-hole well-grounded
socket during using, the same power line avoid using other appliance.
7. Before using this Treadmill, please do 10 minutes of warm-up exercises, should wear
sweat suit、sports shoes and socks.
8. Do not stand on running belt when testing, and do not allow two or more than two
person using the Treadmill at the same time.
9. Should be cautious when up and down; before starting, have to hold the handle, put
two feet on both sides of decorative strips; Speed should from low up to high when
running; When leave the Treadmill, first to make the speed to the minimum in order to
avoid hurt that loss balance.
10. Safety Key have to clip cloths when running, if need to stop can pull-off switch, the
Treadmill will stop running to achieve security purposes. After using, unplug the power
plugs that ensure safety.
11. Need to have adult supervision if children use or near the Treadmill. Patients with heart
disease should not use the machine alone. Physical discomfort under the guidance of a
doctor to use.
12. The Treadmill should avoid solar、raining and moist. Should use cleaning rag to clean
machine in order to avoid the accumulation of dust.
13. Do not stand on Treadmill or placing stuff when not using.
14. Should avoid overload operation for a long time, it may cause damage of Motor and
Controller; Accelerated aging bearing and running belt.
15. When moving the Treadmill, first to fold the bottom frame. After locked, to hold the end
of bottom frame, then carefully move.
16. The treadmill designed for Home Use only, please do not used for organization or
commercial.
Attentions

3
17. Store your treadmill in a clean and dry environment, to make sure the power switch is
turned off and unplug it from the outlet.
二、
No.
name
specification
unit
QTY
1
Base Frame
SET
1
2
Left Side Post
SET
1
3
Right Side Post
SET
1
4
Incline frame
SET
1
5
Main frame
SET
1
6
Console Frame
SET
1
7
Handle Pipe L
SET
1
8
Handle Pipe R
SET
1
9
side post supporter
SET
1
10
Large flat head screws Hexagon
M8*15 BK
PCS
12
11
Large flat head screws Hexagon
M8*30 BK
PCS
1
12
Large flat head screws Hexagon
M8*35 BK
PCS
2
13
Large flat head screws Hexagon
M8*42 BK
PCS
3
14
Large flat head screws Hexagon
M8*55 BK
PCS
8
15
Large flat head screws Hexagon
M8*100 BK
PCS
1
16
Large flat head screws Hexagon
M10*45 BK
PCS
1
17
Lager flat head socket half tooth screw
∮9.8*M8*21.5 BK
PCS
4
18
Socket head socket screw
M8*60 BK
PCS
1
19
Socket head socket screw
M8*80 BK
PCS
2
20
Hexagon anti-skid screw
M8*20 BK
PCS
4
21
Hexagon anti-skid screw
M10*65 BK
PCS
1
22
Cross countersunk head screw
M6*25 BK
PCS
8
23
Cross countersunk head screw
M6*30 BK
PCS
2
24
Slt + phil flat head screw
M4*10 BK
PCS
3
25
Slt + phil cup head screw
M5*15 BK
PCS
2
26
Cross flat head self tapping screw
∮3*8 BK
PCS
41
27
Cross flat head self tapping screw
∮4*15 BK
PCS
33
28
Cross cup head self tapping screw
∮4*30 BK
PCS
4
29
Cross flat head self tapping screw
∮4*55 BK
PCS
2
Parts List

4
30
Storm screw
∮4*12.7 BK
PCS
14
31
Nut
M4 BK
PCS
3
32
Nut
M6 BK
PCS
2
33
Nut
M8 BK
PCS
14
34
Nut
M10 BK
PCS
2
35
Flat washer
∮ ∮
20* 8.5*T1.5 BK
PCS
38
36
Flat washer
∮ ∮
23* 10.8*T1.6 BK
PCS
2
37
Plastic washer
∮ ∮ ∮23* 12* 5*H5.3 BK
PCS
8
38
Plastic washer sleeve
∮ ∮8.5* 4.5*6 BK
PCS
2
39
Pressure rod
QDY22*10-662-292 40KG
PCS
1
40
Front Roller
∮ ∮ ∮90* 46* 17*525*580
SET
1
41
Rear Roller
∮ ∮
46* 17*495（570）
SET
1
42
KSS
6P3-4
PCS
1
43
KSS
6N-4
PCS
1
44
left Handle pipe spigot
54*60*30*T3.3
PCS
1
45
Right Handle pipe spigot
54*60*30*T3.3
PCS
1
46
Meter upper cover
505*787*110*T2.7
PCS
1
47
Meter bottom cover
455*380*64*T2.7
PCS
1
48
Loudspeaker cover
112*97*42*T1.8
PCS
2
49
Key board bracket left
102.5*79*13*T2.0
PCS
1
50
Key board bracket right
102.5*79*13*T2.0
PCS
1
51
Keypad left
18*18*12.7*T1.5
SET
1
52
Keypad right
18*18*12.7*T1.5
SET
1
53
Motor cover
638*341*130*T2.6
PCS
1
54
End cover left
152*106*114*T2.6
PCS
1
55
End cover right
152*106*114*T2.6
PCS
1
56
Cushion
∮25*M8*T20
PCS
4
57
Pad
∮ ∮M8*15* 40* 50 BK
PCS
4
58
Pad
∮M8*15* 28 BK
PCS
2
59
wheels
∮ ∮8.2* 52*T20 BK
PCS
4
60
Running belt
2920*460*T1.6
PCS
1
61
Drive Belt
200J
PCS
1
62
Side Rein
85*37*T3.0*1300
PCS
2
63
Electronic board
5" Blue backlit LCD Display
PCS
1

5
64
Keyboard plate
PCS
2
65
Power cord
L1800mm
PCS
1
66
Red connector wire
L150mm*14AWG
PCS
1
67
Green connector wire
L150mm*14AWG
PCS
1
68
White connector wire
L100mm*14AWG
PCS
1
69
Handle swith wire up segment
3P/250MM
PCS
2
70
Handle swith wire down segment
3P/500MM
PCS
2
71
Heart rate connect wire up segment
2P/310MM
PCS
2
72
Heart rate connect wire down segment
2P/800MM
PCS
2
73
Safety switch wire
2P/460MM
PCS
1
74
Power amplifier power cord
2P/250MM
PCS
1
75
MP3 sound source wire
3P/100MM
PCS
1
76
horn wire
2P/270MM
PCS
1
77
horn wire
2P/400MM
PCS
1
78
Speed sensor
2P/980MM
PCS
1
79
Controller wire up segment
L900mm*10pin
PCS
1
80
Controller wire down segment
L1500mm*10pin
PCS
1
81
Audio signal input wire
L350mm
PCS
1
82
Motor
PCS
1
83
Incline motor
JS-09 179+85
PCS
1
84
controller
PCS
1
85
Rocker switch
16A 250V
PCS
1
86
Safety key
33.5*51*8 800mm
PCS
1
87
Safety key plate
T4.6*18*7
PCS
1
88
overload protector
10A
PCS
1
89
toroidal core
∮ ∮
25* 15*H12mm
PCS
1
90
Heart rate handle
130*34*31.5
PCS
2
91
Power amplifiers
AM003-V10
PCS
1
92
Sound source conversion board
GLP3.5JACK
PCS
1
93
Incline
JC 4Ω 3W
PCS
2
94
Sponge sheath
∮46*T3.0*584
PCS
2
95
Running board
1290*630*T18
PCS
1
96
Rectangle pipe plug
25*50
PCS
2
97
Square pipe plug
40*40
PCS
2

6
98
Motor frame
100*160*30
PCS
1
99
Cross large flat head self tapping screw
∮4*10 BK
PCS
12
100
Bottom curtain board
620*147*T1.5
PCS
1
Assembly drawing

7
四、
Assembling Steps

8
Picture 1
Step1 (as picture 1 show)
1. Unpack the carton and take out all loose parts etc.
and place outside of the carton, take out the treadmill
on the ground and untie it.
2. Fold the treadmill and use the Pressure rod to lock
it.(As picture 1 show)
Step2 (as picture 2 show)
1. Attach Left Side Post (2) into left pipe (1) of base frame, adjust the hole
location aligned. Open hardware bag; take out M8X15L screw (10), flat
washer (35), use correct tools to tight the screw.
2. Across the frame pipe out controller wire (80) through right post (3). Then
insert the right post(3) to the right base pipe(1).Adjust the hole location
aligned ，take out M8X15L screw (10) ,flat washer(35), use correct tools to
tight the screw.
Picture 2

9
Step3 (as picture 3 show)
1. Take out console (46), connect right
controller wire (79) to the wire (80)
from right post (3), and make sure the
connecting is firm.
2. Put the connected wire through the
right post(3)pipe, put the console on
both right post (3)and left
post(2),adjust the hole location
aligned，Open hardware bag, take out
M8X15L screw(14),flat washer(35),
use correct tools to tight the screw.
Step4 (as picture 4 show)
1. take outside post supporter（9）, put
it in the middle of two side posts（2）
（3）,adjust the hole location aligned,
Open hardware bag, take out
M8X15L screw (10) ,flat washer(35),
use correct tools to tight the screw.
Step5 (as picture 5 show)
1. Take out right handle（8), connect wire
(69)(71) from right handle with
wires(70)(72)from right post, and keep
firm.
2. Put the connected wires into console
(46), put right handle (8) on right of the
console, take out M8X55L screw (14),
flat washer (35), and use correct tools
to tight the screw through below of the
console.。
3. Left handle (7) assembling the same
way as right handle (8).
Picture 3
Picture 4
Picture 5

10
六、
1、Instruction Of Keyboards
Panel
Design
5" Blue backlit LCD Display,
two sets humanized touch
keyboards,MP3 audio output
Panel
Display
Time, distance ,speed,
incline, calorie, heart
rate
Running
Area
460*1375MM
Belt
Standard
1.6MM
Max Load
110KG
Treadmill Net
Weight
78KG
Treadmill
Dimensions
Unfolded 1785×805×1330 MM
Folded 1065×805×1580 MM
Treadmill
Gross
Weight
88KG
Technical Parameter
Operating Instruction
1) SELECT Key：In standby mode, can set time, distance,
calorie.
2) STOP Key：The key pressed, motor stop working, be in
standby mode.
3) INCLINE UP/DOWN Key：When treadmill running can
adjust inclines by this Key.
4) ON/OFF FAN Key：Open or close Fan.
5) 0%、4%、6%、8%、10%、12%、14% Key：Incline fast key,
when treadmill running, adjust the incline as the key show.
6) MODE Key：In standby mode, this key pressed can choose
procedure P1-P12.
7) START Key：This key pressed, start the treadmill (3
seconds countdown delay start), start at 1KM/H.
8) SPEED FAST SLOW Key：In SELECT mode choices, can
adjust time、distance、calorie or adjust the running speed.
9) ON/OFF MP3 Key：MP3 audio start and stop.
10) 2、4、6、8、10、12、14Km/h Key：Speed fast key. When
treadmill running, the keys pressed, adjust the speed to the
key show
Picture 6
Picture 7

11
2、Windows display
3、Procedure Instruction
3.1、Normal procedure (P1)
Insert safety key first, turn on power , windows will be in light and with one long
"BEEP", windows display all the numbers is initial value 0, it's the normal mode.
Press START key: after 3 seconds countdown with 3 "BEEP", motor start to work, start
with initial speed 1KM/H.
Press FAST/SLOW key: when treadmill running, it adjust the speed.
Press UP/DOWN key: when treadmills start, adjust the incline.
Press 2、4、6、8、10、12、14KM/H key: when treadmill is working, adjust the speed as
the set value show.
Press 0%、4%、6%、8%、10% 、12%、14% key：when treadmill is working, adjust the
incline as set value show
Press STOP key:：motor stop slowly, wait motor to stop(the original value remain)
3.2、Target Mode（In standby mode operate P2-P6）
Only in standby mode can set this mode;
SELECT Key：In regular turn can set time、distance、calorie，the window blink when the
mode set.
1) 、Time Set
Press FAST/SLOW Key：Default time 30 minutes，can adjust time（5：00-99：00）；
Press START Key：Work mode start（start after 3 seconds countdown）；
2）、Distance Set
SPEED window：display speed；
INCLINE window: display incline
TIME window：display time；
DISTANCE window：display distance；
PULSE window：display heart rate；
CALORIE window：display calorie；
PROGRAM window：display program

12
Press FAST/SLOW Key：Default distance is 1.0KM，can adjust time range
（1.0km-99km）；
Press START Key：Work mode start（start after 3 seconds countdown）；
3) 、Calorie Set
Press FAST/SLOW Key：Default calorie is 500 Kcal，can adjust calorie range
（10Kcal-990Kcal）；
Press START Key：Work mode start（start after 3 seconds countdown）；
3.3、PROGRAM mode
Press MODE Key：Press this key in standby mode to choose P1-P2 program；
Press SELECT Key：Default time is 30 minutes，can adjust time range（5：00-99：
00）；
Press START Key：Work mode start（start after 3 seconds countdown）；
Working mode
According set time change every execute phase, take 90 minutes for example, turn to
next phase in every 3 minutes；
When execute next phase, force back to built-in speed value；
Press STOP Key：Motor stop slowly；
4、Other instructions
When running, press STOP key, speed grind to a halt, incline return to the starting
point ；
Unplug the safety key when running, speed turn to 0, incline return to starting point,
insert the safety key, all data eliminated
5、Daily care and maintenance
5.1、Clean
Keep the appearance clean, make sure the power off before clean the treadmill,
running belt and appearance can be cleansed by soft cloth, attention not leave water on
running belt or display window and the shield;
5.2、Lubrication of Running belt
In using of the treadmill, need to use special lubricant to lubricate the running decking
under the running belt. Suggestion ：
Less than 3 hours every week,：lubrication twice a year；
3-6 hours every week：lubrication every 3 months；
More than 6 hours every week：lubrication every month。
Attention：Use the free lubricant with the treadmill in the packing box.Extra silicone you can
buy from your local shop.
Warning：Stop the treadmill and unplug the safety key before lubricate the treadmill
decking.

13
How to lubricate the running decking?
Find the silicone bottle. In the hardware bag come with the treadmill.
Find a straw can put into the silicone bottle, as picture show
Spray silicone evenly on treadmill deck as the drawing shows.
(ATTENTION: The treadmill MUSTBE STOPPED before applying
the silicone lubricant. This is to prevent injury, otherwise the edge
Of the running belt may cut you or your fingers could be crushed
by the rollers. ) Do not put too much silicone on the deck. Excessive
lubricant may cause slippage of the belt on the rollers.
5.3、Belt Adjustment
All running belts are properly set at the factory，if off-center occur, maybe caused by
followed reasons:
Treadmill is not stable;
User's feet are not in the center of the running belt;
User push off harder with one foot than with another.
If the off-center phenomenon caused by user, can return to normal after a few minutes
running with no loading, If the running belt remains consistently off-center, you will need to
center the running belt manually, If toward the left side of the deck, Using wrench, turn the
left adjustment bolt clockwise 1/2 turn and check ,if toward the right side, turn back a little,
till return to center. (As picture followed)
5.4、Running belt "Slipping"
You may need to adjust the running belt during the first few weeks of use... It may
stretch, appearance is normal when no loading, “slipping" or hesitating when runner plant
the foot during a run, when this phenomenon occur, turn both adjustment bolts clockwise
1/2 turn, make sure the turn of both sides is the same, and every time 1/2 turn, till no
"slipping" and no off-center, Be careful not to tighten the running belt tension too much as
you can create excessive pressure on the front and rear roller bearings. An excessively
tightened running belt may damage the roller bearings that would result in bearing noise
from the front and rear rollers.
5.5、Lubricate rollers
Regularly add drops of silicone to the rollers and shafts to keep the good performance.
5.6、Bolts fastening
Regularly check the bolts、screws and nuts, if any loose, please fasten immediately with
tools.

14
6、Trouble shooting
6.1. Speed error：Show“E1”, after 10s speed signal detected, machine stop automatic.
Solution：1) Adjust the position of speed sensor wire
2) Replace the speed sensor wire
6.2. The safety key is not connected: show“E0”, “SAFETY KEY OFF”
Solution：1）Adjust the position of the safety key.
2）Replace the switching line of safety key.
七、