NordicTrack NETL81810.0 User manual

Serial Number
Decal
Model No. NETL81810.0
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
QUESTIONS?
f you have questions, or if there are
missing parts, please contact us:
UK
Call: 08457 089 009
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
c/o HI roup PLC
Express Way
Whitwood, West Yorkshire
WF10 5QJ
UK
AUSTRALIA
Call: 1-800-237-173
E-mail:
[email protected]
USERʼS MANUAL
www.iconeurope.com

TABLE OF CONTENTS
WARNNGDECALPLACEMENT..............................................................2
MPORTANTPRECAUTONS ................................................................3
BEFOREYOUBEGN ......................................................................5
ASSEMBLY...............................................................................6
OPERATONANDADJUSTMENT ............................................................16
HOWTOFOLDANDMOVETHETREADMLL ..................................................24
TROUBLESHOOTNG .....................................................................25
EXERCSEGUDELNES ...................................................................28
PARTLST ..............................................................................30
EXPLODEDDRAWNG ....................................................................32
ORDERNGREPLACEMENTPARTS ..................................................BackCover
RECYCLNG NFORMATON.........................................................BackCover
This drawing shows the locations of the
warning decals. If a decal is missing or il-
legible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
WARNIN DECAL PLACEMENT
2
NordicTrack is a registered trademark of CON P, nc.

3
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 300 lbs. (135 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. When connecting the power cord (see page
16), plug the power cord into an earthed cir-
cuit. No other appliance should be on the
same circuit. When replacing the fuse in the
power cord adapter, insert an ASTA-approved
BS1362, 13-amp fuse into the fuse carrier.
12. If an extension cord is needed, use only a 3-
conductor, 14-gauge (1 mm2) cord that is no
longer than 5 ft. (1.5 m).
13. Keep the power cord away from heated sur-
faces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTIN on page 25 if the treadmill is
not working properly.)
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 18).
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
WARNIN : To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
IMPORTANT PRECAUTIONS

4
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and press the power switch
into the off position when the treadmill is not
in use. (See the drawing on page 5 for the lo-
cation of the power switch.)
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 24.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
22. Never insert any object into any opening on
the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. DAN ER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
26. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the revolutionary NordicTrack®
T7.0 treadmill. The T 7.0 treadmill offers an impres-
sive selection of features designed to make your work-
outs at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. f you have questions after read-
ing this manual, please see the front cover of this man-
ual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BE IN
Handrail
Upright
Tray
Key/Clip
Power Switch
Walking Belt
Platform Cushion
Foot Rail
dler Roller
Adjustment Bolts
Console
Pulse Sensor

6
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. f there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver ,
adjustable wrench , needlenose pliers , and scissors .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART L ST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: Some small parts may have been preassembled. To avoid dam-
aging parts, do not use power tools for assembly. Extra hardware may be included.
#8 x 3/4" Screw
(1)–10
3/8" Star
Washer (11)–6
#8 x 1" Tek Screw
(5)–4
3/8" Nut (10)–3
5/16" Star
Washer (13)–2
#10 Star
Washer (12)–4
#8 x 1" Screw
(53)–4
#10 x 3/4" Screw
(2)–4
3/8" x 1 1/2"
Patch Bolt (3)–2
5/16" x 1" Flat Head
Patch Bolt (14)–4
3/8" x 4" Patch Bolt (7)–4
1/4" x 1" Patch
Bolt (9)–4 3/8" x 2" Bolt (8)–3
5/16" x 1"
Patch Bolt (4)–2

7
2. With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (55) so that the treadmill is more stable;
do not fully fold the Frame yet.
Remove and discard the two indicated bolts (B)
and the shipping bracket (C).
Cut the shipping tie securing the Upright Wire
(87) to the Base (95). Locate a plastic tie in the
indicated hole in the Base, and use the tie to pull
the Upright Wire out of the hole.
Attach two Base Feet (90) to the Base (95) in the
locations shown with two #8 x 1" Tek Screws (5)
and two Base Foot Spacers (94).
Then, attach the other two Base Feet (90) with
two #8 x 1" Tek Screws (5).
2
95
5
55
90
90
5
5
5
90
94
90
87
Hole
94
1.Make sure that the power cord is unplugged.
Remove the 3/8" Nut (10), the 3/8" x 2" Bolt (8),
and the shipping bracket (A) from the Base (95).
Repeat this step on the other side of the
treadmill.
The 3/8" Nuts (10) and the 3/8" x 2" Bolts (8) will
be used in assembly steps 3 and 6. Discard the
shipping brackets.
95
A
8
10
C
B
1

8
4. dentify the Right Upright (85), which is marked
with a “Right” sticker. Hold the Right Upright
near the Base (95) as shown.
See the inset drawing. Tie the wire tie in the
Right Upright (85) securely around the end of
the Upright Wire (87). Then, pull the other end
of the wire tie until the Upright Wire is routed
completely through the Right Upright.
Wire Tie
87
85
95
87
4
Wire
Tie
85
87
3. See the inset drawing. Cut the plastic tie near
the Upright Wire (87).
Attach a Wheel (96) to the Base (95) with the
3/8" x 2" Bolt (8) and the 3/8" Nut (10) that you
removed in step 1. Do not overtighten the Nut;
the Wheel must turn freely.
Press a Base Cap (89) into the Base (95).
95
8
10
3
96
89
Plastic Tie
Cut
87
5. Hold the Right Upright (85) against the Base
(95). Be careful not to pinch the Upright Wire
(87). nsert two 3/8" x 4" Patch Bolts (7) and a
3/8" x 1 1/2" Patch Bolt (3) with three 3/8" Star
Washers (11) into the Right Upright.
Tighten the 3/8" x 4" Patch Bolts (7) and the
3/8" x 1 1/2" Patch Bolt (3) until the heads of the
Patch Bolts touch the Right Upright (85); do not
fully tighten the Patch Bolts yet.
95
85
87
11
11
3
7
5

9
6. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (55) so that the treadmill is more stable;
do not fully fold the Frame yet.
Remove and discard the two indicated bolts (B)
and the shipping bracket (C).
Attach a Wheel (96) to the Base (95) with the
3/8" x 2" Bolt (8) and the 3/8" Nut (10) that you
removed in step 1. Do not overtighten the Nut;
the Wheel must turn freely.
Press a Base Cap (89) into the Base (95).
6
8
55
10
95
89
96
C
B
7. Hold the Left Upright (84) against the Base (95).
nsert two 3/8" x 4" Patch Bolts (7) and a 3/8" x
1 1/2" Patch Bolt (3) with three 3/8" Star
Washers (11) into the Left Upright.
Tighten the 3/8" x 4" Patch Bolts (7) and the
3/8" x 1 1/2" Patch Bolt (3) until the heads of the
Patch Bolts touch the Left Upright (84); do not
fully tighten the Patch Bolts yet.
With the help of a second person, tip the tread-
mill so that the Base (95) is flat on the floor.
84
7
95
11
11
3
7

10
8. dentify the Left Base Cover (88) and the Right
Base Cover (91). Slide the Left Base Cover onto
the Left Upright (84) and the Right Base Cover
onto the Right Upright (85).
91
85
84
88
8
9. dentify the Left Upright Cover (80). Slide the
Left Upright Cover onto the Left Upright (84).
dentify the Left Handrail (82). Remove the tie
from the bracket on the Left Handrail. f neces-
sary, press the 5/16" Cage Nut (38) back into
place.
Attach the Left Handrail (82) to the Left Upright
(84) with two 5/16" x 1" Flat Head Patch Bolts
(14), a 5/16" x 1" Patch Bolt (4), and a 5/16"
Star Washer (13) as shown. Do not tighten the
Patch Bolts yet.
82
4
14
13
84
80
9
38

11
10. Slide the Right Upright Cover (86) onto the
Right Upright (85). Remove the tie from the
bracket on the Right Handrail (83). f necessary,
press the 5/16" Cage Nut (38) back into place.
Hold the Right Handrail (83) near the Right
Upright (85). nsert the Upright Wire (87)
through the bracket on the bottom of the Right
Handrail. Pull the Upright Wire out of the end of
the Right Handrail.
Attach the Right Handrail (83) to the Right
Upright (85) with two 5/16" x 1" Flat Head Patch
Bolts (14), a 5/16" x 1" Patch Bolt (4), and a
5/16" Star Washer (13) as shown. Do not
tighten the Patch Bolts yet.
38
83
Bracket
14
4
13
86
85
87
10
11. Set the console assembly face down on a soft
surface to avoid scratching the console assem-
bly. Remove the two #8 x 3/4" Screws (1). Lift
off the Crossbar (107).
11
107
Console
Assembly
1

12
12. IMPORTANT: To avoid damaging the
Crossbar (107), do not use power tools and
do not overtighten the #10 x 3/4" Screws (2).
Orient the Crossbar (107) as shown. Attach the
Crossbar to the Handrails (82, 83) with four #10
x 3/4" Screws (2) and four #10 Star Washers
(12); do not tighten the Screws yet.
nsert the Console Frame (102) into the
Handrails (82, 83). Attach the Console Frame
with four 1/4" x 1" Patch Bolts (9); do not
tighten the Patch Bolts yet. Be careful not to
pinch the Upright Wire (87).
Tighten one #10 x 3/4" Screw (2) in each end
of the Crossbar (107); do not overtighten the
Screws. Then, tighten the other #10 x 3/4"
Screw (2) in each end of the Crossbar.
Tighten the four 1/4" x 1" Patch Bolts (9).
12
107
12
9
2
83
102
82
87
9
12
2
First
First
13. Firmly tighten two 5/16" x 1" Patch Bolts (4) and
the four 5/16" x 1" Flat Head Patch Bolts (14)
(only one side is shown).
With the help of a second person, hold the con-
sole assembly near the Right Handrail (83) and
the Left Handrail (not shown).
Connect the Upright Wire (87) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. f they do not, turn one connector and try
again. IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMA ED WHEN YOU TURN ON
THE POWER. Remove the wire tie from the
Upright Wire.
Connect the ground wire from the console as-
sembly to the Console Ground Wire (52).
Console
Assembly
13
Console
Wire
Wire
Tie Ground Wire
83
87
4
52
87
Console
Wire
14

13
14. Set the console assembly on the Left and Right
Handrails (82, 83). Be careful not to pinch any
wires. nsert the excess Upright Wire (87) into
the Right Handrail.
Attach the console assembly to the Crossbar
(107) with six #8 x 3/4" Screws (1). Start all six
Screws, and then tighten each of them.
Attach the two Console Clamps (105) to the
console assembly with four #8 x 1" Screws (53).
14
83
105
53
87
1111
Console
Assembly
82
107
15. Hold the Right Upright Cover (86) against the
console assembly. Align the holes in the Right
Upright Cover with the holes in the Right Upright
(85). Attach the Right Upright Cover with two #8
x 3/4" Screws (1).
Attach the Left Upright Cover (80) to the Left
Upright (84) in the same way.
See steps 5 and 7. Tighten the 3/8" x 4" Patch
Bolts (7) and the 3/8" x 1 1/2" Patch Bolts (3).
15
85 84
11
80
86
Console
Assembly

14
16. f necessary, press the Left Tray (103) and the
Right Tray (104) into the console assembly.
103
104
16
Console
Assembly
17. Raise the Frame (55) to the position shown.
Have a second person hold the Frame until
this step is completed.
Orient the Storage Latch (51) so that the large
barrel and the latch knob are oriented as shown.
Attach the Latch Bracket (6) and Storage Latch
(51) to the Base (95) with two 3/8" x 2" Bolts (8)
and two 3/8" Nuts (10).
Attach the upper end of the Storage Latch (51)
to the bracket on the Frame (55) with a 3/8" x 2"
Bolt (8) and a 3/8" Nut (10). Note: t may be
necessary to move the Frame back and forth to
align the Storage Latch with the bracket.
Lower the Frame (55) (see HOW TO LOWER
THE TREADM LL FOR USE on page 24).
17
18. Make sure that all parts are properly tightened before you use the treadmill. f there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is
used to adjust the walking belt (see pages 26 and 27).
51
95
10
Large
Barrel
8
55
10
6
8
Latch Knob

15
If you purchase the optional chest pulse sensor (see page 23), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1.Make sure that the power cord is unplugged.
Remove the indicated #8 x 3/4" Screw (1) from
the Access Door (108) on the back of the con-
sole assembly.
2. See the inset drawing. Hold the receiver so
that the antenna is oriented as shown. Peel
the paper backing off the pad on the bottom of
the receiver. Press the receiver onto the Access
Door (108) in the location shown.
3. Connect the wire on the receiver to the wire ex-
tending from the console assembly. Make sure
that no wires are pinched. Reattach the
Access Door (108) with the #8 x 3/4" Screw (1).
Discard the other wires included with the re-
ceiver.
Console
Assembly
108
1
Wires
Receiver
Antenna
108

16
THE PRE-LUBRICATED WALKIN BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking belt
or the walking platform. Such substances will dete-
riorate the walking belt and cause excessive wear.
HOW TO PLU IN THE POWER CORD
This product must be earthed. f it should malfunc-
tion or break down, earthing provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a power cord
having an equipment-earthing conductor and an earth-
ing plug. IMPORTANT: If the power cord is dam-
aged, it must be replaced with a manufacturer-
recommended power cord.
Follow the steps below to plug in the power cord.
1. Plug the indicated end of the power cord into the
socket on the treadmill.
2.If you are plugging in the power cord in
Australia, go to step 3.
If you are plugging in the power cord in the UK,
first press the pins on the power cord into the metal
clips in the adapter as shown. Close the adapter
cover over the end of the power cord and tighten the
screw in the adapter. IMPORTANT: Make sure that
the screw is tightened into the adapter cover.
Then, go to step 3.
3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all
local codes and ordinances.
DAN ER: Improper connection of
the equipment-earthing conductor can result
in an increased risk of electric shock. Check
with a qualified electrician or serviceman if
you are in doubt as to whether the product is
properly earthed. Do not modify the plug pro-
vided with the product—if it will not fit the
outlet, have a proper outlet installed by a
qualified electrician.
OPERATION AND ADJUSTMENT
Socket on Treadmill
Metal
Clips
Pins
Screw
Adapter
Outlet
UK Australia
Adapter
Cover
Outlet
Power Cord

17
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable.
When the manual mode of the console is selected, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even mea-
sure your heart rate using the handgrip pulse sensor or
the optional chest pulse sensor.
n addition, the console offers sixteen preset work-
outs—eight quick calorie burn workouts and eight
quick timed workouts. Each workout automatically con-
trols the speed and incline of the treadmill as it guides
you through an effective exercise session.
The console also features the iFit interactive workout
system. The iFit system accepts iFit cards with work-
outs that help you achieve specific fitness goals. For
example, lose unwanted pounds with the 8-week
Weight Loss workout. iFit workouts automatically con-
trol the treadmill. iFit cards are available separately. To
purchase iFit cards at any time, go to www.iFit.com
or call the telephone number on the front cover of
this manual. iFit cards are also available at select
stores.
You can even listen to your favorite workout music or
audio books with the consoleʼs premium stereo sound
system while you get in shape.
To turn on the power, see page 18. To use the man-
ual mode, see page 18. To use a preset workout,
see page 21. To use an iFit workout, see page 22.
To use the information mode, see page 23. To use
the stereo sound system, see page 23.
IMPORTANT: If there is a sheet of plastic on the
console, remove the plastic. To prevent damage to
the walking platform, wear clean athletic shoes
while using the treadmill. The first time the tread-
mill is used, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 27).
CONSOLE
DIA RAM

18
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 16). Next, locate the
power switch on the tread-
mill frame near the power
cord. Press the power
switch into the reset
position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and press the power
switch into the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
23 to turn off the demo mode.
Next, stand on the foot
rails of the treadmill.
Find the clip attached
to the key (see the
drawing at the right)
and slide the clip onto
the waistband of your
clothes. Then, insert
the key into the console. After a moment, the displays
will light. IMPORTANT: In an emergency situation,
the key can be pulled from the console, causing
the walking belt to slow to a stop. Test the clip by
carefully taking a few steps backward; if the key is
not pulled from the console, adjust the position of
the clip. Note: The first time you insert the key into the
console, the incline will automatically rise to the maxi-
mum incline level and then return to the minimum in-
cline level.
Note: The console can display speed and distance in
either kilometers or miles. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE NFORMAT ON MODE on page
23. For simplicity, all instructions in this section refer to
kilometers.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
When the key is in-
serted, the manual mode
will be selected and a
track will appear in the
matrix. f a preset work-
out has been
selected, remove the
key and then reinsert it.
3. Start the walking belt.
To start the walking belt, press the Go button, the
Speed increase button, or one of the speed but-
tons numbered 1 through 18.
f you press the Go button or the Speed increase
button, the walking belt will begin to move at 2
Km/H. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time you press
one of the buttons, the speed setting will change
by 0.1 Km/H; if you hold down the button, the
speed setting will change in increments of 0.5
Km/H. Note: After you press the buttons, it may
take a moment for the walking belt to reach the se-
lected speed setting.
f you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Go button, the
Speed increase button, or one of the speed but-
tons numbered 1 through 18.
Reset
Key
Clip

19
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
ncline increase and de-
crease buttons or one
of the numbered incline
buttons. Each time you
press the incline increase or decrease button, the
incline will change by 0.5%. f you press one of the
numbered incline buttons, the treadmill will adjust
to the selected incline setting. Note: After you
press the buttons, it may take a moment for the
treadmill to reach the selected incline setting.
5. Monitor your progress with the matrix and the
displays.
The matrix—When the
manual mode is se-
lected, the display will
show a track that repre-
sents 1/4 mile (400 me-
ters). As you exercise,
the indicators around
the track will light in succession until the entire
track is lit. The track will then darken and the indi-
cators will again begin to light in succession.
Time display—When
the manual mode is se-
lected, this display will
show the elapsed time.
When a workout is se-
lected, the display will
show the time remaining in the workout rather than
the elapsed time.
Distance/Incline dis-
play—This display
shows the distance that
you have walked or run.
This display will also
show the incline setting
for several seconds, each time the incline changes.
Calories/Pulse
display—This display
shows the approximate
number of calories you
have burned. The dis-
play will also show your
heart rate when you use the handgrip pulse sensor
or the volume level when you press the Volume in-
crease or decrease button.
Speed display—This
display shows the speed
of the walking belt.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.

20
6. Measure your heart rate if desired.
Note: If you use the handgrip pulse sensor and
the optional chest pulse sensor at the same
time, the console will not display your heart
rate accurately. For information on the optional
chest pulse sensor, see page 23.
Before using the
handgrip pulse
sensor, first re-
move the sheets
of plastic from
the metal con-
tacts. n addition,
make sure that
your hands are
clean.
To use the handgrip pulse sensor, stand on the
foot rails and hold the metal contacts for at least
ten seconds—avoid moving your hands. When
your pulse is detected, your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
7. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmillʼs electrical components may
wear prematurely.
Contacts