Venmar Connaisseure C700 SERIES User manual

GLASS PANELS
INSTALLATION INSTRUCTIONS
APPLIES TO THE FOLLOWING RANGE HOOD SERIES
C700, CC700, CIC700, CIS700,
IU600ES, IB700, IC700, IC700ES,
IK700 AND IS700
Venmar Ventilation Inc., 550 Lemire Blvd.
Drummondville QC J2C 7W9
1-800-567-3855
www.venmar.ca
09530 Rev. 02

WARNING
!
• ITIS RECOMMENDED TO WEAR SAFETY GLASSES AND GLOVES WHILE PREFORMING THESE INSTRUCTIONS.
• HANDLE GLASS PANEL WITH CARE.
• ALL TEMPERED GLASS CAN EXPERIENCE SPONTANEOUS BREAKAGE. IFBROKEN, TEMPERED GLASS FALLS
OUT OF IT’SOPENING IN INTERLOCKING CLUMPS. TEMPERED GLASS CAN, ON OCCASION, BREAK INTO
LARGE SHARDS RATHER THAN THE CLASSIC TINY PIECE PATTERN.
• RISK OF ELECTRICAL SHOCK. BEFORE INSTALLING OR REPLACING THE GLASS PANEL, SWITCH POWER OFF
AT SERVICE PANEL AND LOCK SERVICE DISCONNECTING MEANS TO PREVENT POWER FROM BEING SWITCHED
ON ACCIDENTALLY.
CAUTION
AFTER APOWER FAILURE OR DURING THE RANGE HOOD POWER UP, A5-SECOND BOOTING SEQUENCE
IS EXECUTED. WAIT FOR THE CONTROL BACKLIGHTING TO TURN OFF BEFORE USE.
IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
HO0181
Remove filters by pushing them
towards the back of the hood and
tilting them down. Set the filters
aside.
Remove the bottom panel 10 retaining
screws and set aside.
NOTE: Both light assemblies will
have to be disconnected in
order to remove the bottom
panel (see step ).
HO0174
SCREW
LOCATIONS
Slightly pull the bottom panel out.
Press on tabs and pull to disconnect
both light assemblies electrical
harnesses from light connectors.
Slide bottom panel out and set aside.
HO0176
- 2 -
C700 SERIES

Carefully remove the new glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
- 3 -
If need be, remove current glass panel
retaining nuts from both studs. Discard
glass panel and nuts.
Insert new glass panel studs in hood
front holes.
While holding glass panel, pre-tighten
previously removed nuts by hand.
Ensure glass panel is flush with top of
hood and centered from side-to-side.
Then, using a 3/8" socket, tighten nuts
completely.
HD0440
GLASS PANEL STUD
NUT
Insert bottom panel in the back of the hood and reconnect each light assembly electrical
harness to its light connector.
Secure bottom panel to the hood, using the 10 previously removed screws.
Reinstall baffle filters.
IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
HO0247
Remove filters by pushing them
towards the back of the hood and tilting
them down. Set the filters aside.
FOR 30” WIDE HOODS:
Remove the 7 screws (A only)
retaining the bottom panel, and set
aside.
FOR 36” WIDE HOODS:
Remove the 8 screws (A and B)
retaining the bottom panel and set
aside.
HO0246
A
B
Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
C700 SERIES (CONT’D)
IU600ES SERIES

- 4 -
If need be, remove current glass panel retaining nuts from both studs. Discard glass panel and
nuts.
Insert new glass panel studs in hood front holes.
While holding glass panel, pre-tighten previously removed nuts by hand. Ensure glass panel is
flush with top of hood and centered from side-to-side.
Then, using a 3/8" socket, tighten nuts completely.
HD0556
STUD
Reinstall the bottom panel to the hood, using 7 or 8 screws previously removed in step .
Reinstall filters.
FOR EACH GLASS PANEL, IF THE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 6 (CIC700 SERIES)
OR STEP 8 (IK700 SERIES) OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
HO0195
Remove filters by pushing them towards the back (opposite control side) of the hood and tilting
them down. Set the filters aside.
Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
HO0253
CIC700 SERIES IK700 SERIES
NUT
IU600ES SERIES (CONT’D)
CIC700 AND IK700 SERIES

If need be, remove current glass panel
retaining nuts from both studs. Discard
glass panel and nuts.
Insert new glass panel studs in
appropriate hood holes (some parts not
illustrated to ease understanding).
NOTE: Install the glass panel with the
control pictogram on the front of
the hood.
While holding glass panel, pre-tighten
previouslyremovednutsbyhand.Ensure
glass panel is centered.
Then, using a 3/8" socket, tighten nuts
completely. HD0438
GLASS
PANEL STUD
NUT
Reinstall filters.
- 5 -
IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 (CC700 SERIES) OR
STEP 6 (CIS700 SERIES) OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
Remove filters by pushing them
towards the back (opposite control
side) of the hood and tilting them
down. Set the filters aside.
NOTE: CIS700 Series illustrated at
right and below; some details
of your hood may be slightly
different from the ones shown.
Using a Robertson or a Phillips no. 2
screwdriver, remove the 4 electrical
compartment cover retaining screws.
Set cover and screws aside.
HO0190
HD0437
SCREW
LOCATIONS
CIC700 AND IK700 SERIES (CONT’D)
CC700 AND CIS700 SERIES

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
If need be, remove current glass panel
retaining nuts from both studs. Discard
glass panel and nuts.
Insert new glass panel studs in
appropriate hood holes.
NOTE: For CIS700 Series, install
the glass panel with the control
pictogram on the front of the
hood.
While holding glass panel, pre-tighten
previouslyremovednutsbyhand.Ensure
glass panel is centered.
Then, using a 3/8" socket, tighten nuts
completely.
Repeat steps and for the second
glass panel installation. HD0439
GLASS
PANEL STUD
NUT
Reinstall electrical compartment cover and baffle filters.
IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
Remove filters by pushing them
towards the back (opposite control
side) of the hood and tilting them down.
Set the filters aside.
HO0251
Using a Robertson or a Phillips no. 2
screwdriver, remove the 5 electrical
compartment cover retaining screws.
Set cover and screws aside.
HD0560
SCREW LOCATIONS
- 6 -
CC700 AND CIS700 SERIES (CONT’D)
IB700, IC700 AND IC700ES SERIES

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
If need be, remove current
glass panel retaining nuts from
both studs. Discard glass panel
and nuts.
Insert new glass panel studs in
appropriate hood holes.
While holding glass panel,
pre-tighten previously removed
nuts by hand. Ensure glass
panel is centered.
Then,usinga3/8"socket,tighten
nuts completely. HD0561
GLASS PANEL STUD
NUT
Reinstall electrical compartment cover and filters.
- 7 -
IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 7 OF THE HOOD INSTALLATION GUIDE.
IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:
HO0249
Remove filters by pushing them
towards the back (opposite control side)
of the hood and tilting them down. Set the
filters aside.
Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory
installed) from both studs and set aside.
IB700, IC700 AND IC700ES SERIES (CONT’D)
IS700 SERIES

- 8 -
HD0568
HD0569
FRONT GLASS PANEL STUDS LOCATION
REAR GLASS PANEL STUDS LOCATION
HD0558
GLASS PANEL
STUD
NUT
If need be, remove current
glass panel retaining nuts
from both studs. Discard
glass panel and nuts.
Insert new glass panel
studs in appropriate hood
holes.
NOTE: Install the glass
panel with the
control pictograms
on the front of the
hood.
While holding glass
panel, pre-tighten
previously removed nuts
by hand. Ensure glass
panel is centered.
Then, using a 3/8" socket,
tighten nuts completely.
Repeat steps and 
for the second glass
panel installation.
Reinstall filters.
IS700 SERIES (CONT’D)