Venstar T0051FS User manual

OWNER'S MANUAL
MODEL 33CS050/1-FS
Programmable
Digital Thermostat
SmartTemp Equipped
Digital Temperature Selection
Can Display Setpoint, Only
Thermoglow Backlight
Easy, Pushbutton Control
‘Hidden’ Setpoint Limiting
Auto-Changeover
Dry Contact Equipped
Peak Demand Reduction
Manual or Auto Fan Control
F or C Display
Includes Wall Hanger, J-Box Not Required
1 For All
Designed Specifically for the Lodging Industry
Warmer
On/Off
Fan Cooler
AUTO
74
Carrier Corporation 04/07
Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage
Electric Cooling & Gas Heating, Heat Pump, Electric or Hydronic Heat.
Venstar Inc. 12/07
Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage
Electric Cooling & 2 Stage Gas Heating, Heat Pump, Electric or Hydronic Heat.
COMMERCIAL
HEAT
COOL HEAT
PUMP
PROGRAMMABLE
PROGRAMMABLE
up to
& 2-cool
up to
& 2-cool
2-heat
2-heat
HOTEL THERMOSTAT
Backlit display
One For All Works with
Virtually All Equipment
‘O’ or ‘B’ Terminal
Non-Volatile Memory
‘Hidden’ Setpoint Limiting
Peak Demand Reduction
Manual or Auto Fan Control
Mounts Flush with the Wall
Thermostat
Thermostat
Digital
Digital T0051FS
Control up to 2 Heat & 2 Cool Stages
SmartTemp Equipped
Digital Temperature Selection
Optional Setpoint - Only Display
Easy Pushbutton Control
Auto-Changeover
Dry Contact Equipped
Display Either F or C
MULTI-STAGE
MULTI-STAGE
Warmer
Cooler
On/Off
Fan
WITH 48 HOUR
CLOCK BACKUP
Designed Specifically for the Lodging Industry
4Z95
INSTALLATION
INSTRUCTIONS

Table Of Contents
Step #1: Preparation
Step #2: Remove & Replace
Old Thermostat
Step #3: Wire Connections
Step #4: Test Operation
Troubleshooting
2
4
5
13
14
CAUTION Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER -
AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
P/N T0051FS
Venstar Inc. 12/07
Page 1

*‘Mud rings’ or Remodel boxes will not fit. The provided FlatStat
Wall Hanger may also be used. See page 3.
Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
Assemble tools & recommended
Junction Box*.
Flat Blade
Screwdriver
Wire cutter
& Stripper
Make sure your Heater/Air Conditioner
is working properly before beginning
installation of the thermostat.
Carefully unpack the thermostat.
Save the screws, wall anchors, and
instructions.
STEP #1
PREPARATION
Turn off the power to the Heating/Air
Conditioning system at the main fuse
panel. Most residential systems have
a separate breaker for disconnecting
power to the furnace.
EXTENDS
LESS THAN
3/8” FROM
THE WALL.
FLATSTAT
.366”
FlatStat
in Small
J-Box
WALL
WALL
Page 2

Installation Instructions - FlatStat Wall Hanger
TM
Again, making sure the wall bracket is straight up
and down, secure the bracket to the wall with the
two phillips screws provided.
The screws will go through the wall and steel tabs,
‘clamping’ the wall hanger securely to the wall.
When ready to mount the FlatStat to the wall
hanger, use the two # 6 machine screws
provided.
Mark the wall location using the inside opening of
the wall bracket as a template.
Make sure the rectangle is straight up and down
and there is nothing behind the planned opening
inside the wall before cutting.
Cut through the drywall just outside the outline.
Using your fingers, bend the steel tabs around
to the inside of the wall as shown.
INSTALLING FLATSTAT WALL HANGER
Page 3

Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
STEP #2
REMOVE & REPLACE OLD THERMOSTAT
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
Remove the white plastic wire connector
from the rear of the thermostat. Install
wires as directed. Press the wired
connector on the back of the thermostat.
Lift Connector straight up
to remove.
For best operation, install
the thermostat in a junction
box that is free from drafts
that originate inside the wall.
Page 4

STEP #3
WIRE CONNECTIONS
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below,
or the wiring diagrams that follow.
* C may not be used on all systems.
** O/B is used if your system is a Heat Pump.
Wire from the
old thermostat
terminal marked Function
Install on the
new thermos tat
connector marked
G or F Fan G
Y1, Y or C Cooling Y1
W1, W or H Heating W1,O,B
W1,O,B**
PowerRh, R, M, Vr, A R
C
O/b
C *
Common
Rev. Valve
Y2 Y2
W2 W2
2nd Stage Cool
2nd Stage Heat
RS+5 RS+5
Remote Sensor +5vdc
RS RS
Remote Sensor Signal
RS G GND
Remote Sensor Ground
Page 5

Sample Wiring Diagrams
*If using first stage electric heat, this option must be
selected ON (see page 15, step 13 of Owner’s Manual).
Gas or Electric Heat
5 Wire, 1 Stage Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat*,
Electric Cool, split systems & package
units
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
YW
GAS VALVE
or
STRIP HEAT
COMMON
C
FAN
G
Page 6

Sample Wiring Diagrams
Gas or Electric Heat
4 Wire, 1 Stage Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat*,
Electric Cool, split systems & package
units
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
YW
GAS VALVE
or
STRIP HEAT
FAN
G
*If using first stage electric heat, this option must be
selected ON (see page 15, step 13 of Owner’s Manual).
Page 7

Sample Wiring Diagrams
Gas or Electric Heat
6 Wire, 2 Stage Cooling, 1 Stage Gas Heat Residential two stage cooling with
Gas or Electric Heat*.
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
YW
GAS VALVE
or
STRIP HEAT
COMMON
C
FAN
G
2nd STAGE
COOLING
Y2
*If using first stage electric heat, this option must be
selected ON (see page 15, step 13 of Owner’s Manual).
Page 8

Sample Wiring Diagrams
Gas or Electric Heat
6 Wire, 1 Stage Cooling, 2 Stage Heat Residential & commercial 1 Stage Cooling,
with 2 Stage Gas or Electric Heat*
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
YW
GAS VALVE
or
STRIP HEAT
COMMON
C
FAN
G
2nd STAGE
HEATING
W2
*If using first stage electric heat, this option must be
selected ON (see page 15, step 13 of Owner’s Manual).
Page 9

Commercial Gas or Electric Heat *,
Electric Cool, split systems & package units
including Commercial Heat Pumps **
Sample Wiring Diagrams
Gas or Electric Heat
7 Wire, 2 Stage Cooling, 2 Stage Heat
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
YW
GAS VALVE
or
STRIP HEAT
COMMON
C
FAN
G
2nd STAGE
HEATING
W2
*
selected ON (see page 15, step 13 of Owner’s Manual).
** Commercial heat pumps do not have the heat pump turned
ON in advanced setup (see page 15, step 11 of Owner’s Manual).
If using first stage electric heat, this option must be
2nd STAGE
COOLING
Y2
Page 10

Sample Wiring Diagrams
*This option must be selected ON during advanced setup
(see page 15, step 11 of Owner’s Manual).
** This option must be selected O or b during advanced setup
(see page 15, step 12 of Owner’s Manual).
Heat Pump
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
Y O/b
REVERSING VALVE**
COMMON
C
FAN
G
5 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump* with O or b reversing valve**.
Residential Heat Pumps, split systems & package units, with no auxiliary heat.
Page 11

Sample Wiring Diagrams
Heat Pump
CK1
GND
RS
RS+5
W2
Y2
C
G
Y1
W1-O-B
R
POWER
R
COMPRESSOR
Y O/b
REVERSING VALVE**
COMMON
C
FAN
G
6 Wire, 1 Stage Cooling, 2 Stage Heat-Heat Pump* with O or b reversing valve**.
Residential Heat Pumps, split systems & package units, with auxiliary heat.
2nd STAGE
HEATING
W2
*This option must be selected ON during advanced setup
(see page 15, step 11 of Owner’s Manual).
** This option must be selected O or b during advanced setup
(see page 15, step 12 of Owner’s Manual).
Page 12

STEP #4
TEST OPERATION
Press the MODE button repeatedly until
the HEAT icon appears on the display.
Press the UP or DOWN buttons until the set
temperature is 10 degrees above room
temperature. The HVAC unit should
energize in the heating mode.
Press the MODE button repeatedly until
the COOL icon appears on the display.
Press the UP or DOWN buttons until the set
temperature is 10 degrees below room
temperature. The HVAC unit should
Turn the power on to the Heating/Air
Conditioning system.
energize in the cooling mode.
Press the UP button until the setpoint is
equal to the room temperature. Press the
FAN button to Fan On. The fan should turn
on and run continuously.
NOTE: Most equipment has a time delay
of 5 minutes between cool cycles. This
feature is defeatable on the thermostat
(see page 16, step 17 of Owner's Manual).
Page 13

SYMPTOM: When using 4 wires (R, G, W, Y),
the air conditioning equipment tries
repeatedly to turn on, but cannot. At
times the display dims or disappears.
CAUSE: There is not enough power available
to "power share".
REMEDY: Connect a 250 ohm, 10 watt power
resistor at the furnace as shown below.
TROUBLESHOOTING
SYMPTOM: The air conditioning does not
attempt to turn on.
CAUSE: The compressor timer lockout may
prevent the air conditioner from
turning on, for a period of time.
REMEDY: See page 16 of the Owner's Manual
and configure step 17 to defeat the 5-
minute compressor lockout.
R G W Y C
TR300-10w
SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure power is turned on to
the furnace and 24vac between R& W.
If Cis used, 24vac between R& C.
Page 14

SYMPTOM: When controlling a residential heat
pump, and asking for cooling, the heat
comes on.
CAUSE: Heat pump is not selected "ON" in the
Advanced Setup.
REMEDY: See page 15 of the Owner's Manual
and configure step 11 to enable heat pump
operation.
TROUBLESHOOTING
SYMPTOM: When calling for cooling, both
the heat and cool come on.
CAUSE: The thermostat is configured to
control a heat pump and the HVAC
system is a "conventional" (non-heat
pump) system.
REMEDY: See page 15 of the Owner's Manual
and set step 11 to OFF to enable gas
electric operation.
Page 15
4Z95
P/N 88-701
Rev. 1
C
c
F
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
FlatStat T0051FS