VentAHood EUROLINE User manual

Page 1L113 1210A
UL
CUS
R
Read and Save These Instructions
All Hoods Must Be Installed By A Qualied Installer
INSTALLATION INSTRUCTIONS
EUROLINE/EUROLINE PRO
ISLAND RANGE HOOD
Read All Instructions Thoroughly Before Beginning Installation
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be done by qualied person(s)
in accordance with all applicable codes and standards, including re-
rated construction. Switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally
during installation.
B. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
C. Ducted fans must always be vented to the outdoors.
D. Sufcient air is needed for proper combustion and exhausting of gases
through the ue (chimney) of fuel burning equipment to prevent back
drafting. Follow the heating equipment manufacturer’s guideline and
safety standards such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and local code authorities.
E. ASHRAE residential ventilation standard 62.2 limits exhaust fans (total) to
a maximum of 15 CFM per 100 square feet of occupiable space, unless a
back drafting test is performed or make-up air is provided. Consult a local
HVAC engineer for make-up air evaluation.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK

Page 2L113 1210A
Ducting Do’s and Don’ts
NEVER restrict the duct size. The island dual blower unit (T200) requires 8” round duct or
equivalent (50 square inches). The island cluster blower unit (T400) requires 12” round or
equivalent (113 square inches). Using the included Vent-A-Hood transition will ensure proper
efciency.
Do not use exible or corrugated duct. This type of duct will restrict airow and reduce
performance. Only use smooth, galvanized, metal duct. Observe local codes regarding special
duct requirements and placement of duct against combustibles. Make the duct run as short
and as straight as possible with as few turns as possible. Avoid sharp-angled turns. Instead,
use smooth, gradual turns such as adjustable elbows or 45 degree angled turns. For duct runs
over 20 feet, increase the duct diameter by one inch for every ten feet of duct. A 90 degree
elbow is equal to 5 feet of duct. Using Vent-A-Hood roof jacks or wall louvers (back page) will
ensure proper efciency. Airow must not be restricted at the end of the duct run. Do not use
screen wire or spring-loaded doors on wall louvers or roof jacks. Do not terminate venting into
an attic or chimney. Where possible, seal joints with duct tape. The hood must be ducted to the
outdoors without restrictions.
Blower Duct Size Sq. Inch Area Vent-A-Hood Transition
Island Dual (T200) 8” round or equivalent 50” VP565 (Included)
Island Cluster Blower (T400) 12” round or equivalent 113” VP564 (Included)
YES
NO
Smooth Duct Smooth Gradual Turn
Flexible Duct Sharp Angled Turns

Page 3L113 1210A






Installation Details
1) Read all instructions thoroughly before beginning installation. Note: These instructions apply to standard hoods only.
Custom hoods may require additional specication consideration.
2) When installing an island range hood, it is recommended that the bottom edge of the hood be located no more than
30” above the cooking surface. Exceeding recommended mounting height may compromise performance.
3) Load-bearing framework in the ceiling is necessary for the installation of an island hood.
Additional framework construction may be required. Do not attach an island hood to a structure
that cannot support twice the weight of the hood.
If applicable, remove the duct cover from its packaging and remove the hood-mounting
screws from the base of the duct cover. Install the duct cover to the load-bearing framework
in the ceiling using appropriate hardware through the four inside corner mounting anges
on the top of the duct cover.
4) Install the duct from the outside of the home down to the location of the exhaust outlet on the top of the transition plus
1”. This will allow the transition to engage 1” inside of the duct. Consult the connection diagrams (on next page) for
further details on exhaust outlet placement.
Use duct tape to seal all joints. A complete listing of available Vent-A-Hood ducting materials is listed on the back page
of this instruction sheet.
Transition heights are as follows:
Island Dual Blower (T200): 8” round duct connects to 9” tall VP565 transition (included).
Island Cluster Blower (T400): 12” round duct connects to 11 1/4” tall VP564 transition (included).
5) Prepare a protective surface on the oor or countertop for the hood. Remove the hood from its packaging and place
it upside-down on the protective surface for access to the inside of the hood.
Shown with duct cover installed (sold separately).

Page 4L113 1210A
Centerline
Of Hood
5" x 16"
Exhaust
Opening
8" Transition
Opening
Centerline
Of Hood
Vent Holes
Electrical 7 ¾"
12" Transition
Opening 2 ¼”
Above Top of
Hood
8” Blower
Outlets Centerline
of Hood
Centerline
of Hood
Vent Holes
Electrical (2)
7 ¾”
10 ½”
9"
16"5"
8" Round 8" Round
2 ¼”
18”
18"
12" Round 12" Round
11 ¼"
8" Round 8" Round 8" Round
Brass Screws
A
Blower Wheel
B
Blower Housing
Installation Details Continued
6) Remove the blower shields (A) by loosening the two brass screws on the bottom of the shield. Gently close the back
draft dampers from the top side of the hood. To remove the blower housings, unsnap the suitcase latches (B) (one
on each side of the housing). The housings should be pulled forward and gently “tipped” to clear the blower wheels
and then out of the hood.
Warning: Make sure power is off and locked at the service disconnecting
means on the service panel during installation.
Connection Diagram (48”- 66” Widths)
Connection Diagram (36”- 48” Widths)
550 CFM T200 Dual Blower
(Top View)
1100 CFM T400 Dual Blowers
(Top View)
7) Remove the blower deck assembly by removing the 12 screws around the blower mounting plate. Unplug the electrical
connector(s) and set the blower assembly aside, taking care not to damage the blower wheels.
8) Install an appropriate 1/2” UL listed electrical wire clamp through the electrical strap(s) on top of the hood deck. Install
electrical wiring from the service panel to the hood location for each blower assembly. Consult the connection diagrams
(above) for further details on electrical placement. Support the hood beneath the location where it will hang and feed
the electrical wire(s) into the wire clamp(s). Tighten the wire clamp(s).
Transition Installed
(Side View)
VP565 Standard Transition
(Included)
VP564 Standard Transition
(Included)
Transition Installed
(Side View)
Model Volts Amps* Hz RPM CFM
[email protected]" Equivalent CFM•CFM [email protected]"
CFM
[email protected]"
CFM
[email protected]"
Minimum Round
Duct Size Sones#
T200 Island Dual 115 2.9 60 1550 550 900 507 471 431 8" (50 in.2) 6.0
T400 Island Cluster 115 5.8 60 1550 1100 1800 998 855 774 12" (13 in.2) 6.4
* Add 0.5 amp for each halogen light.
• BecausetheMagicLung®blowerusescentrifugalltrationratherthanconventionalbafeormeshlters,theMagicLung®blowercanhandlecookingequipmentwithhighercubicfeetperminute(CFM)requirementsandcandeliverequivalentCFMmuchmore
efcientlythanotherthanotherltrationsystems.WhencomparingtheMagicLung®withotherblowerunitsmadebyothermanufacturers,usethe“EquivalentCFM”.
# RatingsinaccordancewiththeStandardTestCodebytheEnergySystemsLaboratoryoftheTexasEngineeringExperimentStation.

Page 5L113 1210A
Installation Details Continued
9) Raise the hood to its nal position and attach it to the load-bearing framework in the ceiling using appropriate hardware
or to the duct cover using the screws previously removed in Step 3.
10) From inside the hood, using UL listed wire nuts, attach the “neutral” wire(s) to the white lead(s), the “hot” wire(s) to
the black lead(s), and the ground wire(s) to the green lead(s).
Warning: Do not operate hood without proper ground connection.
11) Attach the transition to the blower deck assembly and seal with duct tape. The transition must t inside the exhaust
collar on the blower deck assembly. Reconnect the electrical connector(s). For assemblies with two connectors, connect
the right harness to the front connector and the left harness to the back connector. While taking care to properly align
the duct connection between the transition and the duct in the ceiling, reinstall the blower deck assembly into the
hood using the 12 screws previously removed in Step 7.
12) Replace the blower housings and the blower shields. Make sure that the dampers open and close smoothly.
13) Refer to Owner Maintenance Guide Operating Instructions for proper hood operation. Test all blower and light functions
to ensure they are operating properly.

Page 6L113 1210A
VENTING ACCESSORIES
WALL LOUVER
6”
7”
8”
8 ⁄”
Back
View
1 ½” Flange
MODEL DIM
VP526
VP527
VP528
6” Round
7” Round
8” Round
WALL LOUVER
11”
11”
Back
View
1 ½” Flange
MODEL DIM
VP554 10” Round
WALL LOUVER
13”
13”
Back
View
1 ½” Flange
MODEL DIM
VP555 12” Round
RECTANGULAR WALL LOUVER
3 ¼”
10”
8 ½”
6”
1 ½” FLANGE
2” FLANGE
MODEL DIM
VP538
VP560
6” x 8 ½”
3 ¼” x 10”
LOW PROFILE ROOF JACK
(MAXIMUM 4/12 PITCH)
6 ½”
16 ¾”
16 ¾”
MODEL DIM
VP539
VP540
VP541
6” Round
7” Round
8” Round
LOW PROFILE ROOF JACK
(MAXIMUM 4/12 PITCH)
10 ½”
22 ½”
20 ¾”
MODEL DIM
VP552
VP553
10” Round
12” Round
ROUND DUCT PIPE
36”
6”
7”
8”
MODEL DIM
VP500
VP501
VP502
6” Round
7” Round
8” Round
3 ¼” RECTANGULAR DUCT PIPE
30”
10”
12”
16”
3 ¼”
MODEL DIM
VP504
VP505
VP506
3 ¼” x 10”
3 ¼” x 12”
3 ¼” x 16”
6” RECTANGULAR DUCT PIPE
24”
8 ½”
6”
MODEL DIM
VP507 6” x 8 ½”
OFFSET L & R TRANSITION
FOR ISLAND BLOWERS
8”
12”
5”
16”
MODEL DIM
VP542
VP543
Top Left
Top Right
SIDE VENT TRANSITION L & R
FOR ISLAND BLOWERS
19”
8”
16” 5”
MODEL DIM
VP544
VP545
Side Left
Side Right
“Y” TRANSITION
18”
10”
12”
MODEL DIM
VP517
VP518
VP551
8” & 8” to 12”
6” & 8” to 12”
6” & 8” to 10”
11 ½”
6” x 8 ½”
Opening
9”
WALL COLLARS
2” Larger
Than Cutout
6” Rnd
8” Rnd
2” Larger
Than Cutout
MODEL DIM
VP533
VP535
VP537
6” Round
8” Round
6” x 8 ½”
OFFSET KIT - ROUND
16”
11”
6”
7”
10 ½”
MODEL DIM
VP529 6” Rnd to 7” Rnd
OFFSET KIT - RECTANGULAR
16”
11”
6”
11”
3 ¼” 10”
MODEL DIM
VP550 6” Rnd to 3 ¼“ x 10”
STANDARD ISLAND TRANSITION
8”
9”
16” 5”
MODEL DIM
VP565 5” x 16” to 8” Rnd
CLUSTER BLOWER TRANSITION
18 ½”
12”
11 ¼”
MODEL DIM
VP564 8” & 8” to 12”
BACK/SIDE VENT ELBOW
12”
6”
16”
8” Round
8 ½”
MODEL DIM
VP561 8“ to 6” x 8 ½“
3 ¼” x 10” BACK VENT ELBOW
4 ¼” 10”
14”
3 ¼”
3 ¼”
MODEL DIM
VP559 3 ¼” x 10”
MULTI-BLOWER TRANSITION
VP562 - 17 ½”
VP563 - 16 ½”
10”
12”
VP562 - 23 ¼”
VP563 - 30 ½”
MODEL DIM
VP562
VP563
6” & 8” to 10”
8” & 8” to 12”
3 ¼” x 10”TO 7”TRANSITION
7”
7 ½”
3 ¼”
10”
MODEL DIM
VP521 3 ¼” x 10” to 7”
LOW PROFILE ROOF JACK
(MINIMUM 4/12 PITCH)
6 ½”
16 ¾”
16 ¾”
MODEL DIM
VP539-HP
VP540-HP
VP541-HP
6” Round
7” Round
8” Round
LOW PROFILE ROOF JACK
(MINIMUM 4/12 PITCH)
10 ½”
22 ½”
20 ¾”
MODEL DIM
VP552-HP
VP553-HP
10” Round
12” Round
ADJUSTABLE ELBOW
MODEL DIM
VP513
VP514
VP515
6” Round
7” Round
8” Round
6”
7”
8”
VP513 - 8 ½”
VP514 - 9 ⁄”
VP515 - 10 ⁄”