VentAHood PYD18 User manual

FOR PYD18 EUROPA VENT-A-HOODS
INSTALLATION INSTRUCTIONS
A. Installation Work and Electrical Wiring Must Be Done By
Qualified Person(s) In Accordance With All Applicable
Codes And Standards, Including Fire-Rated Construction.
B. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
C. Ducted fans must always be vented to the out-
doors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
D. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturers guideline and safety
standards such as those published by the NationaI Fire
Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and local code authorities.
Read and Save These Instructions
Turn Page For More Instructions
All Hoods Should Be Installed By A Qualified Installer
Step 1 . . .
Step 3 . . .
Step 2 . . .
Step 5 . . .
Step 4 . . .
Set hood on floor with
wood pallet still attached
to top.
Remove blower deck, light
assembly and transition from
hood.
Run 8 diameter duct and
wiring through ceiling with
section long enough to
reach transition on hood.
Install duct cover to load
bearing framing in
ceiling. For additional
stability in duct covers
over 24 tall, use 1/4 all-
threaded rods.
Attach hood to bottom of duct cover
and re-install blower and light units.
LOAD BEARING FRAMING
(furnished by others)
MOUNTING PLATES ON EACH CORNER
DUCT COVER
4 MOUNTING HOLES
LOCATED IN CORNERS
HOOD
LOAD BEARING FRAMING
CEILING
8 DUCT
TRANSITION
DECK
T200 BLOWER
5 x 16 to 8 DIAMETER
VP546
TRANSITION
FURNISHED
WITH HOOD

1000 N. Greenville Ave. = P.O. Box 830426 =Richardson, TX 75083 =[phone]
Methods of Ducting Your Vent-A-Hood
Venting Materials Available from Vent-A-Hood
- Step 6.  Connect ducting. 
1. Attach venting (before replacing deck if necessary). Do not restrict ducting anywhere
including roof jacks or wall louvers. Do not turn sharp turns with ducting. Make gradual turns
or 45°angles.
- Step 7.  Connect electrical. 
Follow label instructions and remove motor plate. Unplug motor and remove, being careful to not damage blower wheel. Connect electrical, black to
black, white to white and ground to lug provided. Replace motor(s) and dont forget to plug them back in. Replace blower front and be sure it is secured
properly and blower wheel(s) turn freely. Model T200, 3.4 Amps. Hoods with heat lamps and/or halogen lamps, 8.0 Amps.
Observe All Governing Codes and Ordinances
Proper transition is
furnished with hood.
dia.
Mounts under furr-down
Mounts to 8 ceiling
Standard Details
Transition to 8 round
duct furnished
Lip 3
Slope 6
Offset
1
2
/
1 
Blower
Minimum Round
Duct Size
Square
Inches
T-200 Dual 600 CFM 8 (or equivalent) 50
For use on all T-200
blowers with 8 duct
8 8
5 16
12
Other transitions by Special Order
Caution: To reduce the risk of fire or electrical shock, do not use this fan with any solid state variable speed control device.
Roof Jack
tape
8 LP Roof Jack
17
17 1
2
/
6
Round Vent Duct
30
6,7,8,9
8 Adjustable Elbow
8
8
5
8
/
8
8 Wall Louver
Offset L&R Transition
11
16
8
5
16
Side Vent Transition L & R
5
19
8
8
5
12
16
Island Transition
Wall Louver Venting
in 2-Story Dwelling
Hood
Floorline
(2nd floor)
Ceiling Line
(1st floor)
tape
Duct
Outside
Wall
Open
area --
no
screen
8 Roof Jack
/
18
18
161
2
specify
roof pitch
Europa Hoods
Motor Cooling Vent
Wiring Outlet
16
5
8
dia.
2 
/
1
2
7
/
1
2
C
L
C
L
2/25/99 II-PYD18