Ventur IDEO - 275 Ecowatt User manual

CTB
IDEO - 275 Ecowatt
Installation Manual

Before manipulating this device, disconnect the electricity supply.
During normal operation, never stop the ventilation system.

General Information
High-performance heat recovery dwelling unit
1 Introduction
This manual is destined for use with the IDEO 275 Ecowatt high
performance heat recovery unit and its
This
manual
is
destined
for
use
with
the
IDEO
275
Ecowatt
high
-
performance
heat
recovery
unit
and
its
peripheral fittings (conduits, inlets, regulators…).
Its aim is to provide the maximum information and safety during installation, set-up and use.
As our products are in constant evolution, Soler & Palau reserves the right to modify this manual without
prior notification.
1.2 Guarantee and civil liability
Guarantee
The IDEO 275 Ecowatt heat recovery unit is guaranteed for three years from the date of purchase. This
guarantee includes free supply of spare parts.
This guarantee does not cover:
Assembly and disassembly expenses
Any breakdowns which according to Soler & Palau are due to poor installation manipulation negligence
Any
breakdowns
which
according
to
Soler
&
Palau
are
due
to
poor
installation
,
manipulation
,
negligence
or accident.
Any breakdowns occurring after manipulation or repair by third parties without the authorisation of Soler &
Palau.
To return a faulty part, the user should first contact the installer.
Civil liability
The IDEO 275 Ecowatt has been designed for ventilation systems that enable the renewal of air in private
homes. Soler & Palau will not be held liable for damage produced by:
Misuse,
Normal wear and tear of components,
Non-observance of the instructions contained in this manual regarding safety, use and start-up,
The use of components not supplied by Soler & Palau,.
1.3 Safety
General safety rules
The IDEO 275 Ecowatt heat recovery unit has been designed to be incorporated into a ventilation
system.
After installation, there should be no safety, health or environmental hazards, in compliance with EC
regulations. This is also valid for the rest of the products used in the installation.
The following general instructions are important :
Follow the safety instructions to avoid any damage to the fans or harm to people
The technical characteristics of this manual must not be modified
The motor fans must not be modified
The motor fans must be connected to a single-phase 230 VAC / 50 Hz electricity supply
For the installation to be in com
p
liance with EC re
g
ulations
,
the IDEO 275 Ecowatt heat recover
y
must be
pg, y
connected to the electricity supply in compliance with current regulations.
The device must be installed in such a manner that, in normal operating conditions, there is no risk of
contact with moving and/or live parts.
The IDEO 275 Ecowatt complies with regulations on electrical devices.
Before any intervention on the device, always disconnect it from the electrical power supply.
Always use the right tools.
Only use the device for the purpose it was designed for
Only
use
the
device
for
the
purpose
it
was
designed
for
.

2 Technical information
2.1 General definition
The IDEO 275 Ecowatt provides optimum ventilation for a room with a minimum loss of energy. It
extracts air from spaces such as (Bathroom/s WC kitchen and washroom/s or shower room/s
and
extracts
air
from
spaces
such
as
(Bathroom/s
,
WC
,
kitchen
and
washroom/s
or
shower
room/s
,
and
supplies fresh air into the main rooms (Living rooms, bedroom/s, office, …).
The fresh and extracted airflows are separated and filtered. Only the energy from the extracted air is
transferred to the new fresh air introduced. Thanks to IDEO 275 Ecowatt ’s high efficiency heat
exchanger, performance can reach up to 95 %.
Condensation may occur at the moment of exchange, with the introduction of fresh air. This is
recovered in a container for condensate, which should be connected to a waste water drain.
100 %
O2
Thanks to its
100
%
by-pass, the IDE
O
2
75 Ecowatt enables you to cool your home in the summer.
2.2 Description of the IDEO-HR
Antenna
Filter access cover
D 160/150mm
Remote control module
User manual access cover

New fresh air inlet:
The conduit from the outside is connected here.
To avoid condensation, it is recommended to use insulated conduits.
The new fresh air inlet should be fitted sufficiently far from any source of strong
The
new
fresh
air
inlet
should
be
fitted
sufficiently
far
from
any
source
of
strong
contamination (Trees, combustion fumes, roads …).
Supply fresh air into the building:
The conduit blowing fresh reheated air into the building is connected here.
To avoid thermal losses it is recommended to use insulated tubes for moving the
To
avoid
thermal
losses
,
it
is
recommended
to
use
insulated
tubes
for
moving
the
warmed air.
Extracting air from the building:
The building’s air extraction conduit is connected here.
To avoid thermal losses and optimise the performance of the installation, it is
ddt i ltdtb f i th i
recommen
d
e
d
t
o use
i
nsu
l
a
t
e
d
t
u
b
es
f
or mov
i
ng
th
e warm a
i
r.
Discharge extracted air to outside:
The conduit for discharging the extracted air from the building to the outside is
connected here.
This conduit must be hermetic and thermally insulated to avoid condensation
This
conduit
must
be
hermetic
and
thermally
insulated
to
avoid
condensation
both on the inside and outside.
By-pass:
On having avoided the heat exchanger, the system of the by-pass 100 % of the
IDEO
275
Ecowatt
allows
the
introduction
of
the
fresh
air
in
the
night
without
IDEO
275
Ecowatt
allows
the
introduction
of
the
fresh
air
in
the
night
without
being warmed by the warm air accumulated in the house during the day. This
system works automatically or can be forced manually (See chapter 2-6-b).
Without By-pass
functioning
With By-pass
functioning

2.3 Dimensions
Central unit:
Weight: 51 Kg
Remote controls:
Programmable module Kitchen boost

Wall bracket
2.4 Placement
On a vertical wall:
On the floor:
It is recommended to locate IDEO in
heated house space. Otherwise it will
be necessary to insulate the
condensate drain pipework..

On the floor: An specific kit option
Support
It is recommended to locate IDEO in heated house space. Otherwise it will be
necessary to insulate the condensate drain pipework
necessary
to
insulate
the
condensate
drain
pipework
.
Tube cover:
4x
4x

DIAGRAM OF STANDARD ASSEMBLY TYPE “DELIVERY”
Kitchen
Outlet roof caps
CT 150
Toilets
BDOP 125 BDOP 80
Toilets
Air intake plenum
PAP
Air intake D150
Li i / itti
Or
PAF 150
Circular Air intake wall hoods
Li
v
i
ng
/
s
itti
ng room
&
Bedrooms
Or
Or
PAST
Air intake roof D150
10 spigots distributor

Outlet roof caps
DIAGRAM OF STANDARD ASSEMBLY TYPE “DISTRIBUTION”
Outlet
roof
caps
CT 150 Living/
sitting room
BDOP 125
Kitchen
BDOP 125
BDOP D80
+
+
RD80
Bedrooms
Toilets
BAR
+
Toilets
PAP
Air intake D150mm
BDOP D80
+
RD80
+
Or
PAF 150
Circular Air intake D150mm
Or
Or
PAST
Air intake roof hoods D150mm