Ventura 60 User manual

1
Required material for VENTURA 60 litres
ŸM10 attachment set, article no. 1143-00
ŸDrilling machine with drill bit ø 10mm
ŸSpirit level
ŸSocket wrench, SW 17
Figure 2: Bore pattern
Set fixed anchors (see Figure 3). Remove the upper nut along with washer.
Place the container at the desired location and mark out the bore pattern. Alternatively, the bore pattern can be marked out as per Figure 2.
VENTURA 60: Drill ø 10mm holes to a depth of approx. 70mm.
VENTURA 110: Drill ø 12mm holes to a depth of approx. 90mm.
Adjust the lower nut to 25-30mm (the nuts must first be adjusted to the highest point on uneven ground).
Then level out the remaining nuts using the spirit level based on the first nut.
Put the container into position and screw it into place.
Insert the interior container and fix using the securing rod.
Figure 3: Cross-section of attachment
ø10 x 70 / ø12 x 90 25-30 *
45-55 *
* the stated size is only valid at the highest point on uneven ground
Required material for VENTURA 110 litres
ŸM12 attachment set, article no. 1145-00
ŸDrilling machine with drill bit ø 12mm
ŸSpirit level
ŸSocket wrench, SW 19
Figure 1: Remove the interior container
Open container, remove securing rod and interior container (Figure 1).
2
3
4
5
6
7
robi-ag.com
ROBI AG Kohlackerstrasse 17 CH-4323 Wallbach [phone] [phone]
Base assembly for VENTURA 60 / 110 waste bin 15789.2018.01.E.INT
ø10
292
170 (35)
VENTURA 60
240*
(275)
(415)
360*
ø12
380
220 (40)
VENTURA 110
300*
(350)
(500)
460*
* concrete foundation

Figure 1 Figure 2 Figure 3 Figure 4
1
Required material for VENTURA 60 litres
ŸStrapping system (e.g. «Bandimex»)
ŸAllen key 6mm
Required material for VENTURA 110 litres
ŸStrapping system (e.g. «Bandimex»)
ŸAllen key 8mm
Open container, remove securing rod and interior container (Figure 1).
2
3
4
5
Wall mounting for VENTURA 60 / 110 waste bin
Mount the container and screw into place (Figure 4).
Loosen pipe mounting (Figure 2).
Set the pipe mounting on the rod or on the candelabra to the desired height (Figure 3).
Insert the interior container and fix using the securing rod.
1Open container, remove securing rod and interior container.
2
3
4
5
Set fixed anchors (see Figure 2)
Mark out the bore pattern in accordance with Figure 1.
VENTURA 60: Drill ø 8mm holes to a depth of approx. 70mm.
VENTURA 110: Drill ø 10mm holes to a depth of approx. 90mm.
Put the container into position and screw it into place.
Insert the interior container and fix using the securing rod.
6
Required material for VENTURA 60 litres
ŸM8 attachment set, article no. 1144-00
ŸDrilling machine with drill bit ø 8mm
ŸSpirit level
ŸSocket wrench, SW 13
Required material for VENTURA 110 litres
ŸM10 attachment set, article no. 1143-00
ŸDrilling machine with drill bit ø 10mm
ŸSpirit level
ŸSocket wrench, SW 17
45 750
80
VENTURA 60
77 885
80
VENTURA 110
25-30*
* Minimum size with
uneven ground
Figure 1 Figure 2
ø8 ø10
ø8 x 70
ø10 x 90
Post mounting for VENTURA 60 /110 waste bin 15789.2018.01.E.INT
robi-ag.com
ROBI AG Kohlackerstrasse 17 CH-4323 Wallbach [phone] [phone]