Extend and distribute Ethernet and PoE
OUTREACH QUAD and OUTREACH QUAD LITE let you extend and expand
your Ethernet network, with the flexi ility and relia ility of Power over
Ethernet (PoE) power.
OUTREACH QUAD (ORQ) is a five-port Ethernet switch that can forward
PoE to up to four IP cameras or similar devices. This is shown in the
diagram elow:
Installing OUTREACH QUAD dou les the range of the network, and allows
extra PoE devices to e installed rapidly, with no local AC power required.
OUTREACH QUAD LITE (ORQ-LITE) is a five-port Ethernet switch that is
powered y PoE. It provides four remote non-PoE Ethernet ports from a
single PoE-ena led Ethernet connection.
Connections and mounting
Technical specification
Power 3 watts (typical)
PoE In IEEE 802.3af/at Class 4 device (ORQ)
IEEE 802.3af Class 2 device (ORQ-LITE)
PoE Out IEEE 802.3af, PowerPromiseTM managed (ORQ)
Ethernet 10BASE-T or 100BASE-TX, negotiated automatically
Compati le with oth patch ca les and crossover ca les
Switch Unmanaged, store-and-forward switch fa ric
VLAN and jum o packets are supported
Dimensions
( WxDx )
82 x 82 x 21 mm ( 3.23 x 3.23 x 0.83” )
110 x 85 x 21 mm ( 4.33 x 3.35 x 0.83“ ) inc. screws and ta s
Weight 225g ( 7.6 oz )
Environmental Operating temperature: -10 to 50OC ( 14 to 122OF )
Humidity: up to 85%, non-condensing
LED Indicators – Ports 1 to 4
Network status PoE Out status (ORQ only)
On Link On PoE Out ena led
Flashing Activity Flashing Budget exceeded / fault
Off No link Off No PoE requested
LED Indicators – Port 5
PoE In status Network status
Green PoE source connected On Link
Red PoE Plus detected (ORQ only) Flashing Activity
Off No power Off No link
Power budgeting (ORQ only)
Veracity's advanced PowerPromiseTM technology (patent pending) Iimits
the num er of PoE devices that can e ena led at the same time, in order
to prevent any overload or undervoltage conditions in operation.
OUTREACH QUAD has a maximum power budget availa le, which it
allocates according to the power class of any PoE devices connected. This
is the power requested y each device, which may e higher than the
power it actually requires for operation.
You can use the ta les elow to plan your installation. Key:
Class 1 or 2 PoE device (up to 7 watts)
Class 3 device (up to 15 watts)
The first ta le lists how many PoE devices can e connected to OUTREACH
QUAD, according to which type of PoE power source is used:
PoE Source Budget Number of PoE devices supported
PoE 7 watts
OUTSOURCE 15 watts or
PoE Plus 22 watts or
OUTSOURCE PLUS 30 watts or
or
For even longer-reach applications, a single OUTREACH PLUS may e used
to extend the connection etween the PoE source and OUTREACH QUAD.
This reduces the num er of devices that can e connected, however:
PoE Source Budget Number of PoE devices supported
PoE 0 watts (no PoE availa le)
OUTSOURCE 7 watts
PoE Plus 7 watts
OUTSOURCE PLUS 22 watts or
Notes:
1. Some PoE devices are Class 0 (unclassified). OUTREACH QUAD treats these as
Class 2 devices, to avoid udget limit issues in common applications.
2. OUTREACH may e used to extend network connections from OUTREACH
QUAD's PoE Out ports, ut only if OUTSOURCE PLUS is used as the PoE source.
OUTREACH is treated as a Class 3 device
3. All network ports can e always e used as regular (non-PoE) Ethernet
connections, regardless of PoE udget availa ility
4. Operating OUTREACH QUAD with an exceeded udget is not recommended,
as different com inations of devices may e ena led following a reset
INSTALLATION MANUAL
PLEASE READ CAREFULLY
7mm (0.28”) mounting holes
centres 95mm (3.74”) apart
To a 10/100
Ethernet
network
PoE required
from a midspan
injector or PoE
switch
To 10/100
Ethernet
devices
PoE forwarded
(to compliant
devices,
ORQ only)
