Verde Energy Group LED REGAL Series Instruction sheet

Nov21
Product Instructions
VERDE LED REGAL SERIES Power Adjustable Linear Fixture
USER GUIDE：
The purpose of this user guide is to explain the necessary steps for the proper use of a LED REGAL light and
to assure peak performance of this product. It is intended for use as reference by a fully qualified
electrician or technician. This document should never be considered a substitute for any provision of a
regulation or national and/or local code. Please read this entire manual to fully understand and safely use
this product. Specifications are subjected to change without notice. Please visit
www.verdeenergygroup.com for the most recent technical data.
GETTING STARTED This guide contains important information about installing and operating your new LED
REGAL light safely and accurately.
Product description:
MODEL
VER-EB1500-XXPA-840
Power:
Dimensions
(AxBxC)
VER-EB1500-20PA-840
20W
1495 x 155 x 52mm
VER-EB1500-25PA-840
25W
VER-EB1500-31PA-840
31W
VER-EB1500-36PA-840
36W
Declaration of the product:
Each package box includes LED REGAL Power Adjustable light 1pc.
CAUTION:
1. Risk of fire or electric shock. Ensure that the power supply is off when installation is carried out.
2. The light source of this luminaire shall be only replaced by the manufacturer or his service agent
or a similar qualified person.
3. The control gear of this luminaire shall be only replaced by the manufacturer or his service agent
or a similar qualified person.
4. At least double insulation shall be maintained between control conductors and LV supply.
5. Before installation, the fully qualified installer must determine whether the power supply is in
the electrical input range stated in the Product Parameters table (see below) of the luminaire.
6. Do not remove the LED REGAL cover.
7. The LED driver is inside the luminaire.
8. Any constructive change of the luminaire or driver is not permitted.
9. Lamp suitable for 50Hz or 60Hz operation.
10. The device should be installed and operated by a qualified electrician or technician in accordance
with relevant local codes.
11. Do not use sharp tools near or on the surface of the device.
12. Ingress grade IP20.
13. Do not install the light in touch with insulating material under any circumstances.
14. All VERDE products comply with surge immunity as specified by EN 61547:2009. However, the
Verde Warranty also requires additional surge protective devices to be installed on-site against
the effects caused by remote lightning strikes, inductive or capacitive coupling, and switching
surge voltages. These are typically installed at the main distribution and sub-distribution panels
and are to be maintained and operational always. Refer to industry experts such as
www.phoenixcontact.com for further surge protection advice
15. This product contains a light source of energy efficiency class ‘’B’’

Nov21
Unpacking:
1. Unpack and carefully examine the product.
2. Report any damage and save all packing materials if any part of the product was damaged during
transportation.
3. Do not attempt to use the apparatus if it is damaged.
User Responsibilities:
The responsibility to comply with all national and local laws, ordinances, and regulations regarding the
installation, maintenance and operation of the device lies with the buyer and handler of the device. These
parties may include, but are not limited to the contractor, installer, purchaser, owner, and user of the
product. Consult Lighting Application Engineering services as needed.
Product parameters:
Model number
VER-EB1500-XXPA-840
Input Voltage (AC)
Frequency (Hz)
Power
Optics
Working
Temperature (°C)
VER-XB1500-20-840
220-240V 50/60Hz
20W
110°
-20°C to 40°C
VER-XB1500-25-840
220-240V 50/60Hz
25W
110°
-20°C to 40°C
VER-XB1500-31-840
220-240V 50/60Hz
31W
110°
-20°C to 40°C
VER-XB1500-36-840
220-240V 50/60Hz
36W
110°
-20°C to 40°C
Properties:

Nov21
INSTALLATION INSTRUCTIONS:
1. Remove the end cap
2. Open the fitting

Nov21
3. Select the power output on the LED Driver (Default power 36W)
4.Installation
4.a Wiring (side entry)

Nov21
4.b Wiring (back entry)
5. Mounting types
5.a Standard mounting (surface mounting)
5.b Optional accessories for mounting