Veria Control T45 User manual

Veria Control T45
Installation guide
Installationsanleitung
Installasjonsveiledning
Installationsguide
Asennusopas
Installationsvejledning
EN
DE
NO
SE
FI
DK

23
Table of content
Introduction 3
Button and display description 4
Installing and wiring the thermostat 5
Basic functionality
- Select how to control your
 oorheatingsystem   6
 -Recommendedsettings  7
- Setting the clock 8
 -Settingthemaximumoortemperature8
 -Readingtheoortemperature 9
 -Frostprotectionmode 9
Timer functionality
 -ActivateTimerMode  10
 -Programmingthetimer 10
Technical specications 14
Veria Warranty   15
ENIntroduction
Veria Control T45 is an advanced digital timer thermostat, which
allowsyoutocontrolyouroorheatingsystembyeithertheoor
temperature,theroomtemperatureorcombined.
Pleasefollowtheinstructionsinthismanualtoensuremanyyears
oftroublefreeusage.
CongratulationswithyournewVeriaoorheatingsystem....
!Please notice that the thermostat must be installed by an
authorized electrician
EN

45
Button and display description
Currentroomtemperature
Heatingelement
warming
Day of the week
Thermostaton
On/off
Down
Up
Clock
Mode
Currentoortemperature
Installingandwiringthethermostat
Tomountthethermostattothewallbox/wallsocket,rstopenthe
thermostatbygentlypushingthetabsinthebuttomofthethermo-
stat.Toxthethermostat,screwinproperlysizedscrewsintothe
wallsocket/wallbox.
Whenproberlyfastendandcablesconnected(seediagrambelow),
mountthefrontpaneltothebackpartagain.
Electrical wall
box/socket
Wiring diagram
Remotesensor
Model: Veria Control T45
Mains voltage: 85-240V~
raIP ting: IP30
S1
L
Load
S2 L
N
Load
N
13A
Max. load:
Temperature: 0T30
85-240V~
Max
13A
ENEN
Timermodeactivated
Frostprotectionmodeactivated

67
Basic functionality
POWER ON/OFF
Toturnthermostatonoroffpress“ ”
SELECT HOW TO CONTROL YOUR FLOOR HEATING SYSTEM
YourVeriaoorheatingsystemcanbecontrolledeitherbythe:
• Floor temperature - program mode 2
Theheatingelementturnson/offaroundaoortemperature
setpoint(thetemperatureshowninthedisplayistheactual
oortemperature)
• Room temperature - program modes 1 & 4
Theheatingelementturnson/offaroundaroomtemperature
setpoint(thetemperatureshowninthedisplayistheactual
roomtemperature)
• Combined oor and room temperature - program modes
3 & 5
Theheatingelementturnson/offaroundaroomtempera-
turesetpointwitharequestedmax.oortemperature(oor
temperatureisprioritizedoverroomtemperature)
Change between the above oor heating modes:
Withthethermostatturnedoff.
Press “” and “ ”for6seconds
Selectmode1to5(seetableonnextpage)
Afterchoosingthedesiredmodedonotpressanyfurtherbuttonsand
thethermostatwillgobacktonormalstandbymode.
Basic functionality
RECOMMENDED SETTINGS
Veriarecommendsthefollowingsettingsfordifferenttypeofoor
constructions:
Top flooring
Programmode
Wooden
floor*
Tiled
floor**
1
(roomsensor)
Iftotaleffect:0W-1840W x
2
(floorsensor)
Iftotaleffect:0W-2990Wx x
3
(combinedfloorandroomsensor)
Iftotaleffect:1840W-2990Wx x
4
(roomsensor)
Iftotaleffect:1840W-2990Wx
5
(combinedfloorandroomsensor)
Iftotaleffect0W-1840W x x
*Topooringmadeofparquet,laminate,massivewood,carpet,
linoliumorthelike.
**Topooringoftiles,concrete,marbleorthelike.
ENEN

89
Basic functionality
SETTING THE CLOCK
Withthethermostatturnedon.
Press“ ”once,hourwillbeash.
UsetheUp/Downkeytoselectthehours.
Press“ ”again,minutewillbeash.
UsetheUp/Downkeytoselecttheminutes.
Press“ ”buttonagain,tilltheweekdayashes.
UsetheUp/Downkeytoselectthedayoftheweek.
After setting week day do not press any further buttons and the
thermostatwillgobacktonormaloperatingmodemode.
SETTING THE FLOOR TEMPERATURE MAX. LIMIT
Thisfunctionisusedforwoodenoorsmainlyandisonly available
inprogrammodesusingtheoorsensor(programmode3and5)
Thetemperaturesettingshouldbemaximum35C,whichisalsothe
defaultsetpointofthethermostat.
Ifyouchoosetocontroltheoortemperaturesolelybytheoor
sensor(programmode2)themax.oortemperatureissetfor35C
andcan‘tbechanged.
Change the oor temperature max. limit (program mode
3 and 5)
Withthethermostatturnedoff.
Holdthe“M”buttonfor10 seconds until the displayshows“ ”.
Nowletgoofthebutton“M”andthedisplaywillshow“SET”.
Youarenowpromptedtoenterthemaximumoortemperature
(temperaturerange20°C-45°C)
Basic functionality
READING THE FLOOR TEMPERATURE (only in program mode 3
and 5)
Withthethermostatturnedon.
Press“M”once,the“FT ”willbeashed,andthedisplaywill
showtheoortemperature.
Inprogrammode2(oorsensor)thedisplayalwaysshowsthecurrent
oortemperature.
Inprogrammode1and4(roomsensor)thedisplayalwaysshowsthe
currentroomtemperature.
FROST PROTECTION MODE
Toenablefrostprotectionmode.
Withthermostatturnedoff.
Press“M”for3seconds.
Select01(00=disabled)
Whenenabledandthermostathasbeenturnedoff,theheatingwillbe
activatediftheroom/oortemperatureislowerthan5°C; the heating
willbestoppediftheroom/oortemperatureishigherthan7°C.
Whenfrostprotectionmodehasbeenenabledthedisplaywillshow
“”.
ENEN

10 11
ACTIVATE TIMER MODE
Whenusingthetimermode,youmustrstactivatethetimermode:
Withthethermostatturnedon,holdthe“M”buttonfor3seconds.
Youcanselectbelowsettings:
00=Override(disabletimerfunctionality)
01=Programmable.Andthedisplaywillshow“ ”.
Leavethethermostatanditwillgobacktonormaldisplaying.
PROGRAMMING THE TIMER - Mode 01
WhenprogrammingyouneedtoselectProgrammablefunctionand
thedisplaymustshow“ ”(seeabove)
Youcannowsettheheatingprograms.Thethermostatmusthave
4 heating periods for the weekdays and 4 heating periods for the
weekend.
Pleasenoticethattheprogrammingofthewholecalendarweek
must take place in one continuous process,soitisagoodideato
havetheperiodswrittendownforreferencewhenprogramming
thethermostat.
Note, for the weekend you will also need to program 2 periods. You
can choose one of the periods to be very short or in extension of
the other.
Timer functionality
Example, weekdays:
Period1startingat07.00-Temperaturesetting22C
Period2startingat08.30-Temperaturesetting18C
Period3staringat17.00-Temperaturesetting22C
Period4startingat23.00-Temperaturesetting18C
Example, weekend:
Period1staringat09.00-Temperaturesetting22C
Period2staringat23.00-Temperaturesetting18C
Period3staringat23.01-Temperaturesetting22C
Period4staringat23.02-Temperaturesetting18C
My settings:
Week days:
Period1on °C
Period 2 on °C
Period 3 on °C
Period 4 on °C
Weekend:
Period1on °C
Period 2 on °C
Period 3 on °C
Period 4 on °C
Timer functionality ENEN

12 13
How to progamme the timer:
Holdthe“ ”for3seconds,thenumber1and
“MoTuWeThFr”aredisplayed.
Thisindicatesthatyoucanprogramtherstswitchingtimeforthe
week-day.
UseUp/Downkeytosettherequiredstarttime.
Press“ ”toacceptthissetting.
UsetheUp/Downkeytosettherequiredtemp.
Press“ ”toacceptthissetting.
Repeatforswitchingtimes2-4week-day.
Afteryouhaveprogrammedtimes1-4fortheweekday,youarenow
abletosettheswitchingtimesforweekend“SaSu”willbedisplayed.
UseUp/Downkeytosettherequiredstarttime.
Press“ ”toacceptthissetting.
UsetheUp/Downkeytosettherequiredtemp.
Repeatforswitchingtimes2-4fortheweekend.
Todisablethetimer,select“Override”(Mode01)
How to override settings in TIMER MODE
Atanytimeyoucanchangethepresettimertemperaturesettings
by pressing the Up/Downkey.
Yourmanualoverridewillapplyuntilthestartofthenexttimercycle.
Thereafterthethermostatwillresumeyourprogrammedsettings.
Timer functionality ENEN Notes

14 15
Technical specications
Externalsensor: NTC10kOhmat25°C
Sensorvalues:
15°C
18°C
20°C
22°C
14,8kOhm
13,1kOhm
12,1kOhm
11,2kOhm
Display: LCD
Powerconsumption: <2W
Set-pointrange: Room:5°C to 35°C
Floor:20°C to 35/45°C
Accuracy: ±1°C
Buttons: Touch pad
Switchcurrentrating: <13A(resistiveload)
Mainsvoltage: 85-240V~
Dimensions: 86x86x13mm(WxHxD)
Fixingscrewwidth: 60mm
Housing: ABS+PCFlameRetardent
Operatingrating: 0~30°C,5~95%RH(non-con-
densing)
Veria warranty
Warranty certificate
Electrician/installer:
Thermostatname:
Installationdate:
Articlenumber:
Stamp:
Stamp:
Please notice!
InordertoobtaintheVeriawarrantyanauthorizedelectrician/
installermustllinthebelowelds.
Name:
Telephone:
Address:
Zipcode/City:
ENEN