Vexar CEF32M Quick start guide

For more information, visit www.desatech.com
PLEASE READ THIS MANUAL BEFORE INSTALLING
AND USING APPLIANCE.
WARNING: If the information in this manual is not fol-
-
ing property damage, personal injury or loss of life.
FOR YOUR SAFETY
 -

appliance.
 -



-


-
tured Home Construction and Safety Standards.

CONSUMER: Retain this manual for future reference.
ELECTRIC FIREPLACE
OWNER’S OPERATION AND INSTALLATION MANUAL
MODELS CEF32M and CEF36M

www.desatech.com 113470-01D2
SAFETY INFORMATION
TABLE OF CONTENTS
Safety Information ............................................... 2
Product Specication........................................... 3
Installation ........................................................... 3
Features and Operation....................................... 6
Accessory Installation.......................................... 7
Troubleshooting................................................. 10
Wiring Diagram...................................................11
Maintenance...................................................... 12
Technical Service............................................... 21
Replacement Parts............................................ 21
Illustrated Parts Breakdown and Parts List........ 22
Accessories ....................................................... 26
Warranty Information ...........................Back Cover
WARNING: Electrical wiring
    -

regulations to reduce the risk of

to persons.
WARNING: Do not use this
      

    -

replace any part of the electrical
system.
CAUTION: Extreme caution
is necessary when any heater is
-

left operating and unattended.
1. Read all instructions before using this
replace.
2. This replace is hot when in use. To avoid
burns, do not let bare skin touch hot sur-
faces. If provided, use handles when ac-
cessing replace controls. Keep combus-
tible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet from front of replace.
3. Extreme caution is necessary when any
heater is used by or near children or
invalids and whenever the heater is left
operating and unattended.
4. Always place main power switch in the off
position when not in use.
5. Do not operate replace if any part has
been damaged or is malfunctioning.
6. Any repairs to this replace should be
done by a qualied service person.
7. This replace is approved for installation
in bedrooms.
8. Under no circumstances should this
replace be modied. Parts having to be
removed for servicing must be replaced
prior to operating this replace.
9. This replace is not intended for use in
bathrooms, laundry areas and similar
locations where it would be subject to
excessive moisture.
10. This replace may not be installed out-
doors or in an unenclosed space where
exposed to the elements.
11. To disconnect this replace, turn off at
circuit breaker or fuse panel.
12. This appliance, must be electrically
grounded in accordance with local codes
and the National Electric Code, ANSI/
NFPA No. 70 or in Canada with CSA
C22.1 Canadian Electrical code.
13. Do not insert or allow foreign objects to
enter any ventilation or exhaust openings.
This may cause an electrical shock, re
or damage to replace.
14. To prevent a possible re do not block air
intakes or exhaust.
15. This fireplace has hot and arcing or
sparking parts inside. Do not use in areas
where gasoline, paint or ammable liquids
are used or stored. This replace should
not be used to dry clothing or for hanging
decorations.
16. Use this replace only as described. Any
other use not recommended by the manu-
facturer may cause re, electric shock or
injury to persons.
17. SAVE THESE INSTRUCTIONS.

www.desatech.com
113470-01D 3
PRODUCT SPECIFICATION
CEF32M = 155/8"
CEF36M = 17"
CEF32M = 161/4"
CEF36M = 175/8"
CEF32M = 221/4"
CEF36M = 241/4"
CEF32M = 293/8"
CEF36M = 35"
CEF32M = 7"
CEF36M = 8"
CEF32M = 61/2"
CEF36M = 51/4"
CEF32M = 183/8" CEF36M = 21"
CEF32M = 333/8" CEF36M = 37"
CEF32M = 363/8"
CEF36M = 43"
CEF32M = 353/8"
CEF36M = 42"
CEF32M = 345/8"
CEF36M = 411/4"
CEF32M = 325/8" CEF36M = 361/4"
CEF32M = 283/8" CEF36M = 313/4"
CEF32M = 327/8" CEF36M = 361/2"
17/8"
5/8"
TOP
FRONT
LEFT SIDE RIGHT SIDE
CEF32M = 321/8" CEF36M = 361/8"
CEF32M = 283/8" CEF36M = 313/4"
To Nail Location
To Nail
Location
CEF32M = 8"
CEF36M = 51/4"
ELECTRICAL SPECIFICATIONS
Voltage: 120 VAC, 60 Hz
Total Amps: 12.5 Amps
Total Watts: 1500 Watts
Heater Rating: 1100 Watts
Max. Bulb Rating: 100 Watts
Use only on 15 amp circuit
Figure 1 - Unit Dimensions
INSTALLATION
LOCATING FIREPLACE
Plan where to locate and frame replace.
Before installation consider the following:
1. Fireplace location must allow for wall and
ceiling clearances (see Installation Clear-
ances, page 4).
2. Fireplace screen should not be exposed
to direct sunlight from windows or doors.
3. A 15 amp, 120 Volt, 60 Hz circuit with
proper ground must be available. A dedi-
cated circuit should be provided to avoid
circuit breaker trips or blown fuses.
Flush Installations are recommended where
living space is limited or at a premium. Since
the space required to enclose the replace
would be located beyond an outside wall, this
installation would require additional planning
and construction. Check local codes for any
restrictions.
Projected Installations can extend any
distance into the room. A projection may
be ideal for a new addition on an existing,
nished wall.
Corner Installations make use of space
that may not normally be used and provides
a wider and more efcient viewing angle and
heat distribution.
Internal Wall Installations provide a discrete
option for room separation and can also be an
ideal addition to an existing wall.
Figure 2 - Possible Installation Locations
Internal Wall
Installation
Full Projection
Installation
Flush
Installation
Corner
Installation

www.desatech.com 113470-01D4
INSTALLATION CLEARANCES
Minimum clearances to combustible construc-
tion are:
• Top, Back and Sides of Recessed
Cabinet .....................0"Min.
• Drywall to Sides of Front Face . . .0" Min.
• Framing at Nailing Flanges . . . . . .0" Min.
• Ceiling to Opening. . . . . . . . . . . .36" Min.
• Floor .......................0"Min.
• Front ......................36"Min.
• Perpendicular Side Wall . . . . . . .10" Min.
Mantel Clearances
For mantel clearances see Figures 3 and 4.
INSTALLATION
Continued
Facing Material May
Be Noncombustible
Wall Treatments or
Combustible Wood
Combustible Wood
Mantels and Trims
May Extend Above
Profile Shown when
Maintained within 30°
Parameter Shown
Framed
Material
Top of Cabinet
Note: All Mantel Clearances
are Measured from Top of
Fireplace Opening
30°
16 5/8"
Ref.
9 5/8" Ref.
12" Ref.
13 3/4"
4 1/2"
1 1/2"
1 3/4"
10 1/2" Min.
10 1/2"
Figure 3 - Mantel Clearances
Top View of Fireplace
Safe Zone
5"
3"
30° 1 3/4" Max.
Minimum 10" from
Perpendicular Side Wall
Edge of Firebox
Opening
Combustible
MaterialMust
Not Overlap
Front Face
Figure 4 - Mantel Side Clearances
BUILT-IN INSTALLATION
Built-in installations require a framed enclo-
sure constructed of 2" x 2" or heavier lumber
and sized in accordance with Figure 5. This
allows unit to slide into opening and be nailed
to stud at sides and top nailing anges. These
anges accept 5/8" drywall or plywood board
to nish unit ush to face. Optional trim ac-
cessories are available that will extend 1/2"
over rough edge of wall opening (see Acces-
sories, page 26).
IMPORTANT: If installing a perimeter trim kit,
you must install shoulder screws before insert-
ing replace into opening. See instructions
included with trim kit. If installing a mantel,
you must follow clearance instructions (see
Installation Clearances, column 1).
A hearth extension is suggested for a more
pleasing appearance. The replace may be
raised on a wood or non-combustible platform
supporting its entire width and depth and
extending in front of the replace as long as
louvers are not obstructed.
Note: When installing replace in cold cli-
mates against a non-insulated exterior wall,
wall must be fully insulated in accordance with
local building code.
CEF32M = 34 5/8"
CEF36M = 41 1/4"
CEF32M = 15 7/8"
CEF36m = 17 1/4"
CEF32M = 32 5/8"
CEF36M = 36 1/4"
Platform/Subflooring
Figure 5 - Framing Dimensions
CEF32M = 37 5/8"
CEF36M = 42 3/8"
CEF32M = 26 5/8"
CEF36M = 29 3/8"
CEF32M = 52 3/4"
CEF36M = 58 1/4"
11 5/8"
These Dimensions
Allow for 11 5/8" of
Clearance to Side
Wall of Fireplace
and 10' Clearance
to Perpendicular
Side Walls
Figure 6 - Corner Dimensions

www.desatech.com
113470-01D 5
ELECTRICAL INSTALLATION
WARNING: Any electrical re-

 
-
cordance withlocalcodesand/or
in the U.S.A. with the current, Na-
tional ElectricalCodeANSI/NFPA
No 70 and in Canada with CSA
C22.1 Canadian Electric code.
    -

circuit as other appliances may


is in operation.
A junction box with universal strain adaptor is
provided to hard wire unit to a 15 amp, 120
Volt 60 Hz grounded circuit. If necessary,
junction box may be relocated to route sup-
ply to left side.
1. Remove 2 screws and outer cover on right
side (see Figure 7).
2. Remove screw securing junction box to
inside of rebox.
3. Slide junction box up until mounting tab
is lined up to notch in outer cabinet.
4. Swing box out and slip retaining ange
out through slot in outer cabinet.
5. Remove 2 screws and outer cover on left
side and reattach on right side of outer
cabinet.
6. Swing junction box with harness to left
side while pulling sufcient length of har-
ness out through control panel cover to
reach mounting location on left side.
7. Reinsert retaining ange through slot and
swing screw mounting tab back through
notch as before.
8. Slide junction box down until mounting
holes line up and replace inner retaining
cover.
9. Pull end of 3 wire Romex supply line
through universal strain relief bushing in
remaining cover.
10. Strip back outer Romex to about 4” and
connect black, white and green wires ac-
cordingly using approved connectors.
11. Tuck tailing wires into junction box and
replace cover using 2 remaining screws.
12. Tighten down strain adjustment on uni-
versal bushing until Romex sheathing is
secured.
IMPORTANT: Inspect components and wir-
ing for damage before connecting power to
unit. If any components are found damaged,
contact an authorized dealer for original DESA
replacement part(s) or call DESA at 1-866-
872-6040 for referral.
IMPORTANT: Prior to operation remove foam
shipping brace located under motor mount
(see Figure 8, page 7).
Screws
and
Outer
Cover
Junction Box
Mounting
Tab
Notch
Retaining
Flange
Slot
Screws and
Outer Cover
from Other Side
Cover with
Universal
Strain Relief
Figure 7 - Relocating Junction Box to
Left
INSTALLATION
Continued
Junction Box

www.desatech.com 113470-01D6
INSTALLATION
Continued
LAMPS AND LAVA ROCK
Before operating replace, lamp bulbs must
be inspected and lava rock may be added if
desired.
1. Lift log bed off hearth base to gain access
to lamp xtures (log bed is attached with
contact magnets).
2. Turn on power to light circuit and check
that all bulbs are operating. Bulb place-
ment front left to right are red, yellow and
orange (see Figure 9).
Note: If bulbs need replacing there are 3 extra
light bulbs (one of each color) included, see
Replacing Light Bulbs, page 14. Be careful not
to tear or damage reective strips. If they have
come loose, ends can be easily reattached or
replaced at support brackets. See Replacing
Reective Ribbons, page 20.
3. Center log bed over opening between
viewing panel screen and grate.
4. Cover remaining hearth area with 1/4" of
lava rock (provided), if desired.
FEATURES AND
OPERATION
This electronic replace series features a
random ame effect, and a realistic log bed
with glistening embers that can be adjusted for
ame speed and light intensity. These models
have a circulating heater, rated at 1100 Watts
and include a hand detailed, textured, red-
brick lining as standard equipment.
Access controls by pulling two handle tabs
of upper louver until panel releases from
magnetic catches and swings down to open
position (see Figure 10).
Figure 11, page 7, shows control layout for
heater equipped models with main power
switch to ame controls and heater power
switch (when equipped) to heating unit. This
allows independent and efcient operation of
both features.
Once main power is turned on, ame speed
and brightness may be turned on and adjusted
independently.
Figure 8 - Removing Shipping Brace
Foam
Shipping
Brace
Figure 9 - Bulb Placement
Red
Yellow
Orange
Log Bed
Figure 10 - Accessing Controls
Motor
Mount
Grate
Viewing Panel
Screen

www.desatech.com
113470-01D 7
ACCESSORY
INSTALLATION
OPTIONAL GLASS DOORS
These models come equipped with basic-
black bifold glass doors that are fully operable
and will accept a full door panel in any of 4 trim
styles, (see Accessories, page 26).
Installing Bifold Glass Doors
Follow these steps to install left and right
operable panels:
1. With handle down, completely fold panel
on its hinges.
2. With handle facing center of rebox open-
ing insert lower pivot pin on door panel
into hole in bottom outer edge of rebox
opening (see Figure 12).
3. Keep folded door tilted and slide upper two
pins into guide track below upper facial
edge of rebox opening.
4. Tilt glass assembly fully vertical until outer
pivot pin snaps into mounting hole in up-
per spring clip.
5. Once top and bottom pins are secured,
unfold door into closed position.
6. Repeat steps 1 through 5 for opposite
door assembly.
7. To adjust doors, slide partially open. Using
a Phillips screwdriver, loosen hold-down
screws on spring clips (see Figure 13).
8. Close both doors until evenly joined at
middle and note gap as measured to outer
edges of front face.
9. Reopen each door one at a time and
retighten the hold-down screw while pre-
serving noted gap at each edge.
10. Repeat process until both doors are even-
ly joined, spaced and working freely.
FEATURES AND OPERATION
Continued
Figure 11 - Control Panel
Figure 12 - Installing/Removing Glass
Doors
Spring Clip
Depress Spring
Clip to Release
Pivot Pin
Remove Pivot Pin
From Bottom Face
While Sliding Door
Out of Upper Track
Pivot Pin
Fold Bifold Door
After Releasing
Spring Clip to
Slide Door Out of
Upper Track
Figure 13 - Adjust Glass Door
Spring Clip
Partially
Opened
Door
Side Front
Face
LOWLOW
MAIN
POWER HI- OFF
FLAME SPEED
HI- OFF
FLAME BRIGHTNESS
HEATER
ON/OFF
Switch Flame Brightness
Flame Speed
Heater Switch

www.desatech.com 113470-01D8

Remove bifold doors for replacing or cleaning.
1. Partially open each door and press up on
upper spring clip with a screw driver until
outer top pivot pin is free of the clip.
2. Fully fold frame assembly and slide upper
edge towards center of rebox opening
until the guide pins are free of the frame
rail (see Figure 12, page 7).
Installing Fixed Glass Doors
1. Hold glass door rmly at both handles and
insert top pins into clips located below up-
per facial edge of rebox opening. Make
sure top pins snap securely into holes on
spring clips (see Figure 14).
2. Push up on glass against tension of spring
clips. Swing lower door into face until lower
pins clear bottom rail and set into locating
holes on each end (see Figure 14).
Note: If pins do not align into spring clips,
slightly loosen retaining screws on each clip
(see Figure 13, page 8). Reinsert panel into
each spring clip and align panel into lower
locating holes. Remove panel, tighten screws
and reinsert panel.
ACCESSORY
INSTALLATION
Continued
Figure 14 - Installing Fixed Glass Doors
Spring Clip
Locating
Hole
OPTIONAL BRICK LINERS

These models come standard with red brick
liners. There are white brick liners available
(see Accessories, page 26). These brick pan-
els may be installed any time after replace
installation is complete.
Follow these steps to install left and right
brick panels:
1. Remove glass doors (if equipped). Follow
instructions under Optional Glass Doors,
page 7.
2. Remove each retaining screw holding
screen rods and pull entire screen and rod
assembly out of locating hole on inside top
edge of rebox (see Figure 15).
3. Remove log bed from hearth pan and
place in a safe area. Log bed is attached
with contact magnets only.
4. Remove two screws holding each refrac-
tory bracket to rebox. Pull up and lift out
of positioning slot at bottom of hearth pan
(see Figure 16, page 10). Note: CE36M
model requires removal of additional
hearth brackets and face panels which
are held in place by 2 screws on hearth
pan and one screw at top retainer bracket
(see Figure 16, page 9).
Figure 15 - Removing Screen/Rod
Assembly
Screen
Rod
Retaining
Screw
Locating
Holes

www.desatech.com
113470-01D 9
ACCESSORY
INSTALLATION
Continued
5. Insert brick panel, beveled edge first,
through rebox opening. Tilt and angle top
edge into brick retainer until beveled edge
contacts imager and panel is at against
rebox (see Figure 17).
6. Align hearth pan bracket over holes near
lower edge of brick panel and secure with
2 pan screws provided.
7. Replace refractory bracket using 2 screws
removed in step 4, page 8.
8. Repeat steps 5 through 7 for opposite
panel assembly.
9. Replace each screen assembly by po-
sitioning screen rod into locating holes
under top edge of rebox and securing
with 2 Phillips screws removed in step
2, page 8. Note: Rods may have to be
angled into locating holes at the top of
each screen pocket. Once inserted, pull
free end of rod forward until it lines up
over farthest mounting hole respectively
so rods overlap.
10. Replace log bed over hearth opening
and center between grate and viewing
screen.
11. Replace glass doors if removed. See
Optional Glass Doors, page 7.
Figure 16 - Removing Refractory Bracket
and Hearth Pan Bracket
Face Panel
(Model CE36M
Only)
Hearth Pan Bracket
(Model CE36M Only)
Refractory
Bracket
Figure 17 - Installing Brick Panels and
Brackets
Refractory
Retainer
Bracket
Hearth Pan
Bracket
Refractory
Bracket

www.desatech.com 113470-01D10
TROUBLESHOOTING
Note: Before troubleshooting system, make sure power to circuit from breaker or fuse panel
is turned ON.
The three most common causes of a malfunctioning electric replace are:
1. Tripped circuit breaker or blown fuse.
2. Loose or burned out light bulb.
3. Obstructed or clogged fan blower.
POSSIBLE CAUSE
1. No power to replace
2. Defective switch lamp
3. Defective wiring
1. Tangled or loose flame
pennants
2. Obstructed or clogged fan
blower
3. Damaged or dislodged fan
blower wheel
1. Burned out or loose light
bulb
2. Broken lamp xture
3. Loose or missing reective
ribbons
1. Obstructed heater blower
2. Burned out heat element
or blower fan
3. Defective heater switch or
wiring
REMEDY
1. Check circuit breaker or fuse
2. Replace defective switch.
See Servicing Control Pan-
el, page 15
3. Check connections from
main power harnesses to
terminals on control panel.
See Servicing Control Pan-
el, page 15
1. Inspect ame pennants. Un-
tangle or replace if neces-
sary. See Servicing Flame
Pennants, page 17
2. Check fan blower for de-
bris. Vacuum areas around
blower wheel and remove
any obstructions. See Main-
taining Motors, page 14
3. Remove and inspect fan
blower housing See Servic-
ing Fan Blower, page 17
1. Inspect light bulbs; tighten
or replace light bulbs as
necessary. See Replacing
Light Bulbs, page 14
2. Remove and replace broken
lamp xture. See Replacing
Lamp Fixtures, page 19
3. Inspect reective ribbons.
Reattach or replace as nec-
essary. See Replacing Re-
ective Ribbons, page 20
1. Clear heater fan of debris
or blockage; vacuum area
around blower intake and
remove any obstructions
in the discharge area. See
Maintaining Motors, page 14
2. Removing and replace
blower heater assembly.
To access and remove
see Heater/Blower Unit,
page 12
3. Inspect wiring connections
from switch to blower. Re-
place switch if defective.
See Servicing Control Pan-
el, page 15
OBSERVED PROBLEM
No operation or indicator light
at power/heater switch
Poor ame motion; ame pat-
tern is sporadic or uneven in
viewing area
Dull ame appearance or inac-
tive ember bed effect
No heat or intermittent heat
output. (If equipped with a
heater)

www.desatech.com
113470-01D 11
WIRING DIAGRAM
YELLOW LAMP
WHT
HARNESS 4" BLK
HEATER
POWER
FRONT HARNESS TO LAMP CIRCUIT
RED LAMP
SPLICE CONNECTION
MALE CONNECTION
FEMALE CONNECTION
GRN
BLK
WHT
BLK
SUPPLY
ORANGE LAMP FAN MOTOR
FLAME PROJECTOR - ELECTRICAL DIAGRAM
WHT
BLK
CONTROL PANEL - ELECTRICAL DIAGRAM
BLK
HARNESS 24"
WHT BLK
GRN
GRN
WHT
FLAME
CONTROL
TERMINAL
CD AB
BLK
5 L
4 LN 1
BLK
GRN
BLK
FAN
CONTROL
CD B
TERMINAL
HARNESS 4" BLK
REAR HARNESS TO
MOTOR CIRCUIT
BLK
BLK
BLK
A
WHT
5 L
BLACK
BLK 4 LN 1 MAIN
HEATER ASSEMBLY - ELECTRICAL DIAGRAM
HEATER
COIL
RED
RED
BLK
BLK
MOTOR CUTOUT
WHT
CAUTION: USE SUPPLY WIRES SUITABLE FOR 105°C OR EQUIVALENT
CAUTION: DISCONNECT FIREPLACE FROM THE ELECTRICAL SUPPLY
BEFORE REMOVING THIS COVER
POWER
CONNECTION
HARNESS
4" WHT
BLK
WHT
BLK
WHT
WHT - ALTERNATE
CIRCUIT
Figure 18 - Wiring Diagram

www.desatech.com 113470-01D12
MAINTENANCE
HEATER/BLOWER UNIT
WARNING: Disconnect
   
maintenance or cleaning to re-
     
shock or personal injury.
Any electrical repairs work
     
    
in accordance with national and
local codes.
These models come equipped with a blower/
heater installed. Service or replace blower/
heater as follows:
1. Open upper control door (see Figure 10,
on page 6) and remove 2 Phillips screws
below heater grill on control panel (see
Figure 19).
2. Remove 2 Phillips screws holding control
cover to control panel inside rebox (see
Figure 19).
3. Slide control cover to the right and swing
out locking tabs from notched openings
on top (see Figure 19) .
Figure 19 - Disassembling Blower Mount
Control
Panel
Control
Cover
Blower
Mount
Control
Cover
Screws
Hex
Screws
Notches for
Control Cover Blower Mount
Notch (1 of 4)
Screws
Figure 20 - Mounting Heater/Blower
Figure 21 - Mounting Alternate Heater/
Blower
Harness
Strap
Heater/
Blower
Assembly
Blower
Mount
Mounting
Screws
Mounting
Screws
Heater/
Blower
Assembly Blower
Mount
4. Let control cover hang down off har-
nesses. Be careful not to damage any
wiring. If necessary, unscrew harness
strap at blower mount to gain slack.
5. Remove 2 hex screws at rear of blower
mount (see Figure 19).
6. Disconnect White wire from terminal
marked A-B and black and red wires from
terminals N-1 and L-4 on heater power
switch. See Figure 22.
7. Slide blower mount towards rear of rebox
until locking tabs line up with notched
openings and blower mount down and
away (see Figure 19).
8. Remove old blower/heater assembly from
blower mount (see Figure 20 and 21).
9. Align new blower assembly over hole pat-
tern on blower mount and attach with 4 pan
head screws provided.

www.desatech.com
113470-01D 13
10. With discharge pointing towards you, guide
assembled blower mount into replace
and center rear mounting anges between
standoff brackets at rear of the replace.
11. Lift blower mount up and position 4 locking
tabs through notched openings in rebox
top. Slide assembly forward until locked
into position.
12. Connect white heater wire to neutral con-
nection marked 'B' or 'A' on terminal block.
See partial wiring diagram, Figure 22.
13. Connect black heater wire to terminal
marked 'N-1' on heater power switch (see
Figure 23). Note: On alternate style heaters
white and black wires are connected com-
mon to terminal 'N-1' (see Figure 24).
14. Connect red heater wire to terminal
marked 'L-4' on heater power switch (see
Figure 23 or 24.
15. Replace 2 hex screws on rear anges of
blower mount removed in step 5, page 9.
16. Remount harness strap to blower mount,
if removed.
17. Make sure all wires are clear of heater
discharge area, line up mounting holes
on front blower mount to holes in control
panels and replace the 2 black pan head
screws.
18. Raise control cover up and position 2
locking tabs through notched openings in
rebox top, then slide to left until locked
into position (see Figure 19, page 12).
BLK
BLK
TERMINAL
WHT
BLK
GRN
BLK
D C
CONNECTION
SUPPLY
RED
RED
N 1
4 L
5 L
HEATER
COIL
AB
HEATER
POWER
MOTOR
WHT
CUTOUT
WHT
WHT
WIRES TO HEATER CIRCUIT
WHT - ALTERNATE
BLK
HARNESS 4" BLK
Figure 22 - Heater Circuit Diagrams
Rocker
Switch
Red (L-4) Black (N-1)
Heater/
Blower
White
(A-B)
Terminal Block
Figure 23 - Connecting Heater Wires
Rocker
Switch
Red (L-4)
White (N-1)
Heater/
Blower
White
(A-B)
Terminal Block
Figure 24 - Connecting Alternate Heater
Wires
MAINTENANCE
Continued
19. Tuck any excess slack in harnesses into
control cover. Swing cover down to line
up mounting holes on control panel and
replace 2 Phillips screws removed in
step 2, page 9.
20. Restore power to unit and check operation
of the heater.
IMPORTANT: Be sure to inspect components
and wiring for damage before connecting
power to unit. If any components are found
damaged, contact an authorized dealer for
original DESA replacement parts(s) or call
DESA at 1-866-872-6040 for referral.

www.desatech.com 113470-01D14
WARNING: Do not exceed
-
    
-
ing property damage, personal
injury, or loss of life.
REPLACING LIGHT BULBS
There are (3) colored lamps rated at 120V,
100 Watts, for use in a medium sized socket.
These bulbs are located under the log bed
and can be replaced as follows:
1. If you are unsure which bulb needs
replacement, defective bulbs may be
visually located as any of 3 bulbs colored
- Red, Yellow and Orange starting from
the left (see Figure 9, page 6). Defective
bulbs can be replaced individually or for
convenience you may want to replace all
bulbs at the same time; even if only one
is defective.
2. Disconnect power to unit at main breaker
or fuse panel.
3. Lift log bed off hearth base to gain access
to lamp xtures. Log bed is attached with
contact magnets only.
4. Remove each defective bulb from its
socket and replace with appropriate color
and size bulb.
Note: Be careful not to tear or damage reec-
tive ribbons. If they have come loose, they
can be easily reattached or replaced at the
support brackets. See Replacing Reective
Ribbons, page 20.
5. Return power to circuit and turn main power
switch and lamp power on to check opera-
tion of bulbs before replacing log set.
6. If all bulbs are working properly, replace
the log bed over the center opening in
between rear screen and front grate.
CAUTION: Make sure power
is turned off at supply prior to

MAINTAINING MOTORS
Motors used on fan and heater assembly are
permanently lubricated and do not require
lubrication. Annual cleaning and/or vacuuming
around heater and fan unit is recommended.
REMOVING/REPLACING CONTROL
DOOR
The upper control door may be removed for
service or replacement when necessary:
1. Open upper control door (see Figure 10,
page 6).
2. Remove 4 Phillips screws from deector
shield. Angle deector shield out of open-
ing (see Figure 25).
3. Remove 4 Phillips screws from magnet
assemblies.
4. Lift up on inner control door and push
in each end until pivot pins are free of
notches located on each side of access
opening (see Figure 25).
5. Rotate control door up into control com-
partment and slide on end into side of
compartment.
6. Tilt out one end rst then pull remaining
door assembly through opening.
7. Replace door, by starting with door upside
down, pins up and facing unit. Follow step
5 in reverse until pins are rmly set back
in notches and door will close.
8. Replace discharge deector and magnet
assemblies.
SERVICING CONTROL PANEL
The control panel can be serviced from inside
the unit by removing rear control cover on
inside of rebox. Follow steps 2 through 4
under Heater/Blower Unit, page 12.
Figure 25 - Removing/Replacing Control
Door
Deector
Shield
Control
Door
Magnet
Assembly
Push
Door Up
and
Back
Angle
Door and
Slide
Out of
Housing.
MAINTENANCE
Continued

www.desatech.com
113470-01D 15
If control assembly needs complete replace-
ment, proceed to remove the entire control
assembly as follows:
1. Remove the glass doors (if equipped).
Follow instructions under Optional Glass
Doors, page 7.
2. Remove each retaining screw holding
screen rods and pull entire screen and rod
assembly out from locating hole on inside
top edge of replace (see Figure 26).
3. Remove log bed from hearth pan and
place in a safe area. Log bed is attached
with contact magnets only. This step is
included to keep logs from being damaged
during panel replacement.
4. Remove 2 Phillips screws holding control
cover to control panel inside rebox (see
Figure 19, page 12).
5. Slide control cover to the right and swing
out locking tabs from notched openings on
top. See detail Figure 19, page 12.
6. Pop out bushings on control cover and slip
power harnesses free from control cover
(see Figure 27).
7. Remove magnet assemblies, deector
shield and control door. See Removing/
Replacing Control Door, page 14.
8. Tilt entire control assembly forward to
clear lower ange at upper door rail and
slide assembly down through space be-
tween the front face and rebox mount
(see detail Figure 28).
9. Angle control panel out through opening
(see Figure 28).
10. Follow these instructions in reverse order
to reassemble control panel assembly.
Note: Be certain that all wires, harnesses and
bushings are returned to their normal position
and free of damage before reconnecting sup-
ply power to the replace.
CAUTION: Note the location
of all wires prior to disconnect-
ing. Be sure to reconnect wires
to their proper locations. If you

locations, follow the wiring dia-

ACCESSING IMAGING UNIT
The imaging unit can be accessed from inside
replace for servicing as follows:
1. Remove glass doors (if equipped). See
Optional Glass Doors, on page 7.
2. Remove screens, grate, hearth pan brack-
ets and brick liners. See Figure 29, page
16 and instructions under Optional Brick
Liners, page 8.
3. Remove 4 Phillips screws holding hearth
pan to replace and 2 screws located at
lower frame rail (see Figure 30, page 16).
MAINTENANCE
Continued
Figure 27 - Detaching Power Harnesses
LOWLOW
MAIN
POWER
FLAMESPEED FLAME BRIGHTNESS
HEATER
Panel Screws
Figure 26 - Panel Screws Location
Figure 28 - Removing Control Panel
Control
Panel
Power
Harnesses
Bushings
Control
Cover

www.desatech.com 113470-01D16
4. Lift rear ends of hearth pan up until front
edge clears lower frame rail then slide
up on end and angle out of replace
opening.
5. Remove 4 Phillips screws holding face
extensions at top refractory clips (see
Figure 30).
6. Remove viewing screen from cabinet
face. Viewing screen is attached by mag-
nets (see Figure 31).
Note: Do not scratch viewing screen. Place
on a nonabrasive surface away from work
area. When replacing viewing screen painted
side must face inside of cabinet with pattern
facing up.
7. Remove 4 Phillips screws on base cover
and lift cover off cabinet base. See Figure
32, page 17.
Note: Only CE32M series models have Face
Extensions that require removal to access
Imaging Unit. Model CE36M series has in-
ner Face Panels that also require removal to
access Imaging Unit.
MAINTENANCE
Continued
Figure 29 - Accessing Imaging Unit
Refractory
Brackets
Grate
Hearth Pan
Bracket
Hearth Pan
Bracket Brick Liner
Brick
Liner
Figure 30 - Removing Hearth Pan and
Face Extensions (Extensions for E32
Series Only)
Hearth Pan
Face Extensions
Refractory Clip
Viewing Screen
Figure 31 - Removing Viewing Screen

www.desatech.com
113470-01D 17
SERVICING FAN BLOWER
To remove fan blower:
1. Follow instructions under Accessing Imag-
ing Unit, page 15.
2. Remove 3 light bulbs from lamp xtures
(see Replacing Light Bulbs, page 14).
3. Disconnect two 1/4" blade connectors at
from posts on motor unit.
4. Remove 4 hex nuts and washers located
on blower mounts at base of cabinet (see
Figure 33).
5. Lift entire fan assembly off of mounts and
tilt out of unit.
6. Remove screws with washers and hex
nuts from fan housing.
7. Mount new fan to blower mount in reverse
order.
8. Slide blower assembly with spacers over
mounting lugs and replace washer and
nut at each lug. Do not over tighten.
9. Attach blade connectors to posts on
motor mount. Note: Wire connectors for
fan motor are non-polarized and may be
connected to either terminal for proper
operation.
SERVICING FLAME PENNANTS
If ame pennants should become tangled or
detached reattach or replace.
1. Locate affected ame pennant. Slip hem
at base of ame pennant over proper
hanger bracket position. See Figure 34,
page 18, for proper location.
2. Pull ame cord up to proper hook location,
use a slip knot to adjust cord length and
attach cord to hook.
3. Tie another knot over slip knot and trim
away excess cord.
MAINTENANCE
Continued
Figure 32 - Removing Base Cover
Base
Cover
Figure 33 - Removing Fan Assembly (Shown without Firebox for Clarity)
Washer
Hex Nut
Fan Assembly
Blower
Mount
(1 of 4)
Washer Hex
Nut
Screw
Spacer
Posts for Blade
Connectors

www.desatech.com 113470-01D18
8"
7"
3 1/2"
1 1/2"
Figure 34 - Locating Flame Pennants
Flame Cord
Flame
Pennant
Flame
Spacer
MAINTENANCE
Continued
Note: Flame pennant should not be twisted or tangled and should hang slightly loose to allow
free movement. If cord is too short or pennant is torn you must obtain a replacement ame
assembly (see Replacement Parts, on page 21).
4. After connecting and adjusting ame cords, soak each knot with a drop of white wood
glue or clear nail polish to prevent unraveling.
Hook

www.desatech.com
113470-01D 19
Figure 35 - Replacing Fixtures (Shown without FIrebox for Clarity)
Screws and
Washers
Hanger
Screws
Reective
Ribbon
Lamp
Fixture
Crimp
Connectors
Screws
Reective
Ribbon
Cellophane
Tape
Base
Cover
REPLACING LAMP FIXTURES
Lamp xtures may be replaced as follows:
1. Turn off all power to replace at circuit
breaker or fuse.
2. Locate any of 3 defective lamp xtures
and trace wiring to crimp connectors in
harness and disconnect.
3. Remove 2 crimp connectors in harness
and disconnect white and black wires on
defective xture. See Wiring Diagram, Fig-
ure 18 on page 11, for proper locations.
4. Remove 2 Phillips screws at base of
defective xture (see Figure 35).
5. Remove old xture and mount new xture
with 2 Phillips screws removed prior.
6. Twist bare ends of white and black wires
to corresponding wires in main harness
and secure them with 2 crimp connectors
provided.
MAINTENANCE
Continued
Note: There should be no exposed bare
wire at any connection. Wiring should be
secured with wire ties, as short as possible,
and kept away from fan blades. If additional
parts are required, see Replacement Parts,
on page 21.
7. Replace each light bulb with proper color,
(see Replacing Light Bulbs, page 14).
8. Restore power and check lamp circuit
operation before reassembling imaging
unit.
9. Reassemble imager. See Accessing
Imaging Unit, page 15.
Make sure power is turned off

this unit.
IMPORTANT: Be sure to inspect components
and wiring for damage before connecting
power to unit. If any components are found
damaged, contact an authorized dealer for
original DESA replacement part(s) or call
DESA at 1-866-872-6040 for referral.
Upper Hanger
Bracket
Bottom Hanger
Bracket
Ribbon Support
Bracket

www.desatech.com 113470-01D20
MAINTENANCE
Continued
14. Center log bed over opening between
viewing panel screen and grate.
15. Cover remaining hearth area with 1/4" of
lava rock (provided), if desired.
CLEANING VIEWING SCREEN
Clean viewing screen with an alcohol based,
nonabrasive, residue free cleaner (premoist-
ened hand wipes are ideal). Do not use glass
cleaners with ammonium, abrasive scrubs or
degreaser solvents of any kind.
ACCESSING IMAGING UNIT FOR
REPLACEMENT
The imaging unit can be removed from inside
the rebox for servicing or replacement:
1. Follow steps under Accessing Imaging
Unit, on page 16.
2. Remove 4 hex screws on lower louver
panel and detach louver assembly from
front face (see Figure 36).
3. Rotate top edge of lower frame rail inward
and lift upward until locking tabs detach
from front face (see Figure 36).
4. Slide entire imaging unit forward and lift
out through front opening (see Figure 37,
page 21).
Note: An additional 3 feet of harness is tucked
behind imager to permit removal without dis-
connecting any control wiring.
REPLACING REFLECTIVE RIBBONS
If reective ribbons become damaged or loose
they may be replaced as follows:
1. Turn off all power to replace at circuit
breaker or fuse.
2. Locate defective ribbon; there are 3 strips
mounted on rear cabinet and 3 mounted
in base (see Figure 35, page 19).
3. If upper back cabinet ribbons need re-
placing, remove 4 Phillips screws holding
corresponding bottom and top hanger
brackets (see Figure 35, page 19).
4. Remove any loose or damaged ribbon
material.
5. Cut an 18” strip of reective ribbon and
position top end about an inch above top
bracket position (see Figure 35, page 19).
Note: Ribbon material should be ap-
plied with reective side up, should not
be twisted or tangled, and should hang
slightly loose to allow free movement.
If additional parts are required, see Re-
placement Parts, page 21.
6. Replace top hanger bracket using 2 Phil-
lips screws removed in step 2 and tighten
until reective ribbon is held in place.
7. Replace bottom hanger bracket using 2
remaining Phillips screws to secure lower
end of reective ribbon.
8. If replacing reective ribbons located in
base, remove screws and washers at
damaged ends of ribbon.
9. Cut a 9" long strip of ribbon and apply
across each ribbon support bracket with
shiny side facing up (see Figure 35,
page 19).
10. Secure ribbon to brackets by replacing
each washer at end of the ribbon and re-
threading screws through the ribbon into
each hole located on support brackets.
11. If replacing top reective ribbons on base
cover, cut a 3" section of ribbon and split
down the middle. With shiny side up, attach
with cellophane tape into rear edge of base
cover opening (see Figure 35, page 19).
12. Readjust ame pennants (if removed). See
Servicing Flame Pennants, page 17.
13. Reassemble imager. See Accessing
Imaging Unit, page 15.
Figure 36 - Removing Lower Louver
Panel and Frame Rail
Lower Panel
Lower
Frame
Rail
Lower Frame
Rail
Locking Tab