VFARM VGROW Tower 3.0 User manual

1
VF@RM User Manual
Standard VGROW Tower 3.0
PLEASE READ THESE INSTRUCTIONS CAREFULLY
1. Below Table 1.1 attached with Standard VGROW Tower 3.0 checklist.
Please DOUBLE check on the items provided.
2. Step-by-step installation guide with pictures are provided.
3. ***Things to take note listed below.
4. Please inform our customer support ASAP for any missing/broken parts, so
that they can update your situation on time.
5. For any more doubts and questions, our customer support is ready to assist
you within working hours (Mon-Fri 9.00am-6.00pm)
6. Please stay connected with our customer support to ensure you a smooth and
satisfied progress.
No.
Items
Quantity
Check
1
Black host
X1
2
Pots
X11
3
Water tank
X1
4
Enhanced Potting mix
±2L X1
5
Net Cup
61 cups
Table 1.1 VGROW Standard Tower 3.0 Checklist

2
***How to dilute my dry fertilizer?? (Refer to Page 10)
***How to detect the amount of sunlight needed?? (Refer to Page 11)
For more item images, you can find them
in the installation guide.
6
Filter bag
61 pieces
7
Water pump
X1
8
Pump head
X1
9
Pak Choy seeds
1 pack
10
VFERT Bottle (Fertilizer)
500ml X1
11
White plate base + one screwed pot
1 set

3
VGROW Standard Tower 3.0
Step-by-step installation guide (13 steps)
STEP 1:Put the water pump into the WATER TANK.
STEP 2: Connect the water pump with its PUMP HEAD.

4
STEP 3: Connect the pump head with BLACK HOST.
STEP 4: Connect the POTS with White plate base + one
screwed pot.

5
STEP 5: Join them at the CONNECTING POINT one by
one. Total: 5 connecting points for each POT. Tightly secure
the POTS until level 6th
STEP 6: After that, put six level of the pots + white plate
base into the water tank through Black Host.

6
STEP 7: VERY IMPORTANT!! Gently press the white
plate base to ensure it is equally tight. The water pump cable
should be taken out through the corner hole of the white plate
base.
STEP 8: Connect the other six of the pots at the connecting
point one by one. Then, connect all of the POTS through
Black host.

7
STEP 9: Ensure the pots at level 6th and level 7th are tightly
secured.
STEP 10: Cover the black host with a piece of filter bag.

8
STEP 11: Cover the filter bag with a net cup.
STEP 12: Fill up the water tank until the arrow pointed level, then
turn on the electricity. You may turn on the electricity for 24 hours / from
8am to 8pm (at least 12 hours water flow).

9
STEP 13: Slightly shake the upper part of the tower to
ensure water flows equally on the pot.
After you have done all of the steps above. You
are happy to start your vertical farming journey.

10
Things to take notes: REMEMBER!!!
1. Check your pump once you have received your parcel.
It can be done by turning on your pump. If the vibration holds
for more than 10 seconds, then your pump is in a good
condition.
2. Never leave your water level less than half of the tank.
Always keep an eye on the water level. Normally, you may
need to refill once a few days.
3. Never leave your pump on while there is no water/not
enough water
It can BURN your pump easily!!!!
How to dilute your dry fertilizer:
1. Simply fill up 70% of your VFERT bottle with tap water.
2. Shake the bottle well until you don’t hear any “substance
noise”. This means your dry fertilizer has been diluted
completely.
3. Then, you may fill up the other 30% with tap water.
4. Directly pour VFERT into the water tank once a week.
(Kindly refer back to the Growing Manual on the proportion
needed per week.)
**May filter out the undissolved particles to prevent any blockages.